Question about 2001 Ford F150 Styleside SuperCrew

1 Answer

Putting gears back into the pumkin without the gears locking up

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 557 Answers

Rears are very difficult that is why only a very few repair shops will touch them. You need some presision machinist tools to set it up or you will turn the gears into power in a very short time. Take it to a pro, not something you can be talked thru online.

Posted on Nov 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 98 ram 1500 2wd just had the rear pumkin gears


Sounds more like transmission problems.Check the transmission fluid.

Sep 06, 2014 | Cars & Trucks

2 Answers

Rear pumkin assembly bolts in front not back how do i get it out


remove the axles then the tail shaft then the bolts . You will need a chisel and hammer as the diff center will be stuck to the housing until you break the seal from the gasket sealant

Oct 26, 2013 | 2002 Chevrolet Tracker

1 Answer

When replacing my rear wheel bearing and oil seal the two small gears in the pumkins feel out I need to know how to put them back in


There should be 2 cone type washers with the gears, the washers go on the bigger part of them, they will set into the hole in the center. First, rotate the gear carrier so you can reach both sides, take both gears with the washers in place and lightly hold them at 180 degrees so they mesh with the side gears. You then rotate one axel slowly to roll the small gears into place [ this may take a couple times to get them lined up so the shaft will go back in]. When you install the locking bolt, it would be a good idea to clean the threads on both parts and use a thread locking compound.

Apr 18, 2011 | 1987 GMC VanDura

1 Answer

I put new tires on my zj an they are 245 70 16 in the front they are from a junk yard an the ones in the rear are 225 70 16 i drove bought 14 miles maybe an could smell gear oil i stopped an looked an on...


no way man he told you wrong, if you run different sized tires its like changing the gear ratio. one differential is gonna be faster than the other and chew it up. thats a big difference in tire size too so you did some damage. need to demand they fix it.

Mar 31, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

I want to check the grease in the rear end where is the plug?


take a look at the side of the pumkin or third member near the pinion gear

Mar 17, 2011 | 1998 Dodge Ram 1500 4WD

1 Answer

1997 ford f 150 xlt 4x4 it feels like its stuck in low gears it goes in all the gears and not in 4x4


Check vacuum pod on front axle at the gear hub or pumkin it will have a black plastic cover over it this pod engages the gears for 4X4. Remove cover and spray down with WD 40.

Mar 12, 2010 | 1997 Ford F150 Regular Cab

1 Answer

No problem. I'm just looking to find the rear end gear ratio that's in the pickup.


It will be stamped on the differential pumkin. That is the removable part if there is one, or the center if there is no removable part.

Mar 11, 2010 | 2006 Dodge Dakota

1 Answer

How do i change the spider gears in a 2004 chevy silverado 1500


Take off pumkin cover, on center pin in the diff there is a bolt on the botton of the bigger opening that holds pin in place, take the bolt out of the pin and tap the pin out. You have to tap out one side to get out one gear, then tap the pin back through and do the same thing for the other gear. Once you get the upper and lower gears out there are C clips that you have to take out so you can slide the axles out at the two middle gears will pop out.

Oct 30, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

2 Answers

2002 Saturn Lseries trouble putting into gear at starup.


It has to be shift lock solenoid (actuator). When this solenoid goes out it makes it so you can't put the vehicle into gear. Replace this and your vehicle will go back to normal. Good luck and let me know how it turns out. Thanks for using FixYa!

Jun 30, 2009 | 2007 Saturn VUE Green Line

3 Answers

85 f250 2wd, 6.9D, 4spd, Dana 60 rear


Look on the back of the wheels by going under the vehicle. and tell me if you see a light oil. I am sure yours is a sealed pumkin. If not the oil in the pumkin may have leaked out

May 24, 2009 | 1985 Ford F 250

Not finding what you are looking for?
2001 Ford F150 Styleside SuperCrew Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...