Question about 1998 Mercury Villager
Motor may be bad. Have to remove trim panel for access. Cheap on ebay.
Posted on Jan 16, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: power windows
I had the same problem alot with a 95 Windstar. you need to replace some relays in the fuse panel under the dash. it should be labeled on the cover. unfortunately i've since sold the van... but i believe you need to replace the one touch down relay.
Posted on Mar 18, 2009
The problem is most likely a bad dual climate control valve. This component is located on the right side near the radiator under the hood. It will have several coolant hoses hooked to it and 2 silver cylinders protruding from it. You can clamp off the heater hoses at the heater core and see if both sides cool then and this will tell you that the valve is letting coolant thru when it shouldn't be.
This will narrow it down to either the valve or the control head inside the car,or wiring in between them. The only way to narrow it down further is if you have a scan tool that could access the climate control data. Have seen several of these valves cause this concern and have only seen one control head cause it.
Posted on Apr 02, 2009
That is correct, the air blend door actuator. "flapper valve" may need to be replaced or cleaned and free from binding up. Good luck and hope this helps. If there is an Auto Zone in your area, they can order the part you need and give you the step by step instructions to removing the old actuator and replacing it if it's damaged. Good luck and keep me posted, be glad to help.
Posted on Aug 22, 2009
There is a "blend" door on some models with automatic climate control and/or dual zone heat and air. If your model has this option, this might be the source of your problem. Possibly the blend door is stuck and can be freed easily if you're lucky. I have heard of some repairs for this problem to be quite costly, so definitely check around and get several diagnoses from reputable sources before jumping into this.
Posted on Jun 20, 2010
Tips for a great answer:
Dec 17, 2016 | 2008 Chevrolet Equinox
Apr 25, 2016 | Ford Mustang Cars & Trucks
Jul 29, 2012 | 2003 Chevrolet TrailBlazer
If this occured after trying to close the shade while the moonroof was opening, it is possible that the plastic tab that locks into the vent (and subsequently the rest of the moonroof) has been bent. I was having a similar problem where my vent would only go up on one side and stay closed on the other (and it would sometimes get stuck open). It would also prevent the rest of the moonroof from opening up. If this is the case, from what I can tell, there is no easy fix for this. Upon researching this problem, you are the only other person asking about it and zero fixes. For the time being, the vent can be closed by lifting up on one side to "unlock" the stuck tab and you should be able to put it down. After that, you should look up instructions to remove your moonroof glass to see if you can inspect the affected area to determine the cause. Here is a link that shows you how to remove the moonroof glass, but does not address the exact issue you describe.
Jun 17, 2012 | 2005 Subaru Outback
Apr 12, 2012 | 2003 Buick Rendezvous
Feb 06, 2010 | 2000 Chevrolet Silverado
Jul 24, 2009 | 1999 Chrysler Town & Country
May 23, 2017 | 1998 Mercury Villager
61 people viewed this question
Usually answered in minutes!