Question about 1998 Toyota Tacoma

Open Question

How to change alterbator belt on 98 Toyota Tacoma

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 261 Answers

SOURCE: 98 Tacoma exhaust manifold

the best way i know is to heat the bolts using asceteline and oxygen and then use an impact to break them loose.

Posted on Nov 15, 2008

Ad
MrScary66613
  • 1990 Answers

SOURCE: procedure to change serpentine belt 2006 toyota tacoma?

Here is your Solution!
You will need to Locate the Belt Tensioner. It has a Large Pulley on a Bracket that Has a Bolt in the Middle and a Smaller Pulley that Goes Under the Belt and Holds Tension on it. You will need to get a Wratchet, Socket, and Cheater Bar. Turn the Bolt On the Top Large Pulley with the Wratchet and Cheater Bar. This will Lower the Smaller Pulley So that you will be Able to Remove the Belt. Please Rate My Response! Thanks! P.S. the link below is for the Belt Routing Diagram.
http://www.mvreader.com/multiview/dayco/catalogSearch.php?autoCatalogSearch=1&make=TOYOTA&model=TACOMA&year=2006&year_from=&year_to=&engine=All&l=n

Posted on Feb 06, 2009

  • 1 Answer

SOURCE: how to change the check engine light on a 2000 toyota tacoma

i had the same thing, i had it tested at auto zone and they said it was the obd2. i was told the o2 sensor was not a big deal so i reset the check engine light by holding down the trip meter button while starting her up and it has not been on since.

Posted on Jun 23, 2009

  • 59 Answers

SOURCE: working on a 98 toyota tacoma v6 4wd 3.4l eng. I

Yes,need to make sure crank is at TDC as well

Posted on Oct 09, 2009

  • 7353 Answers

SOURCE: have p0130 and p0133 codes 98 toyota tacoma

I would check the O2 sensor, and if it checks bad, replace it, and clear the trouble codes. If the light comes back on, you may need to check further. .

Posted on Oct 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Number 4 cyl. misfire/ 2.4rz engine/98 toyota p.u. how to fix misfire of number 4 cyl.on toyota 98 tacoma p.u./2.4rz engine


check compression, check valve clearance, check injector for properly working, check for vacuum leak around this cylinder.

Feb 10, 2015 | 1998 Toyota Tacoma

1 Answer

Ive got to replace a timing belt on a 98 toyota tacoma, my problem is that the two marks on the top of my timing belt and cover are not exact. in therory the two cam shafts should be at the top aswell the...


You will probably have to take your timing belt off, allign the marks, then put your belt back on. Had the same problem. That's what I had to do. They have to be alligned. Check your book though. I think all has to be at 12 o'clock but I am not 100% sure.

Jan 13, 2011 | 1999 Toyota Tacoma PreRunner

1 Answer

I HAVE TOYOTA TACOMA PRERUNNER TRD-OF ROAD 2006 WITH 94000 MIL. WATH CAN OF MAINTENANCE SERVIS NEED TO DO


Replace the antifreeze with Toyota Lifetime, change the diff fluid, some dealers recommend tranny flush at 100K, change the serpentine belt. Be prepared, you have WS tranny fluid, the flush is $200+

Jul 27, 2010 | 2006 Toyota Tacoma

1 Answer

1996 tacoma belt replacement, all belts


Dear Belt Replacer,
Nothing special you need to know, just that to make sure you take the belts off and reinstall them in the correct order, also make sure that each belt has between half an inch and one inch of play when the final tension is set on each belt, thx, I'M HERE TO HELP!!!

Nov 22, 2009 | 1998 Toyota Tacoma

2 Answers

Have p0130 and p0133 codes 98 toyota tacoma


check the mass air flow sensor there maybe dirt on the filiment inside the sensor causing false readings. cleaning or replacing it may make the codes go away.

Oct 28, 2009 | 1998 Toyota Tacoma

1 Answer

Working on a 98 toyota tacoma v6 4wd 3.4l eng. I


Yes,need to make sure crank is at TDC as well

Oct 09, 2009 | 1998 Toyota Tacoma

1 Answer

Where is expansion valve located on 98 toyota tacoma


The expansion valve is located inside the evaporator box. the book gives you about 1.4 hours to change it but if your not sure about working on ac systems I would recommend using a licensed repair facility.

Aug 25, 2009 | 1998 Toyota Tacoma

1 Answer

98 Tacoma exhaust manifold


the best way i know is to heat the bolts using asceteline and oxygen and then use an impact to break them loose.

Oct 07, 2008 | 1998 Toyota Tacoma

Not finding what you are looking for?
1998 Toyota Tacoma Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...