Question about 1992 Eagle Talon

2 Answers

Dont start bangs and pops back fire

My name is john my car was running fine its a 1992 eagle tayon itwas running ruff now it no start and it pops and back fire dont run it starst for a sec then bangs

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

I'm Very sorry to have to tell you that your engine has jumped time.In other words timing belt or chain depending on what engine you have has sliped ,cracked ,or broken ,the cam shaft must rotate in the exact correct position with the crank shaft ,or ya get the symptons you have now.I hope this helps you ,good luck.

Posted on Nov 14, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Sounds like your timing is way off. First I would check your fuel pressure at the fuel rail and also check for spark to make sure you are getting plenty of good strong spark.
Your 02 sensors tell the engine how much fuel to give. Lean/Rich mixtures

If 02 sensors are bad, car will act the same way. Does sound like timing though which is controlled by your car's computer.

You can go to and register for full free online repair manual.

If you have a testing light, you can connect it to #1 plug wire, then aim at crankshaft pulley while someone else turns car over. Then you can see if the timing is off.

Posted on Nov 14, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Bad misfire

run the fault codes as misfire can be from injectors , low fuel pressure and ignition problems
all temp gauges will show a rise on stopping an engine as there is still residual heat in the block and heads with no water circulation and cooling
the fire from the exhaust indicates an exhaust valve is not closing properly so a compression test would be in order to check for valve problems or hydraulic follower problems

Aug 05, 2015 | Cars & Trucks

1 Answer

Starts but runs ruff then dies

Hi Glean, Sounds as if you have a problem with the fuel pump or possibly the air flow sensor. Take the vehicle for a scan and if no fault codes show up suspect the pump. Regards John

May 18, 2012 | 1995 Nissan Maxima

1 Answer

I got 1992 Chevrolet C1500. Have changed plugs, wires, distributor cap and rotor button. Have also changed fuel filter. After it warms up it starts skipping and running ruff. What can I try now?

Sounds like throttle position sensor or mass air flo sensor.Both of these can be checked by hooking up to computer.You dont want to ramdomly start changing sensors can get costly.

Feb 12, 2011 | 1992 Chevrolet C1500

1 Answer

What is the firing order on engine left 2 right and coil packs front to back

1992 Eagle Talon FWD 2.0 liter DOHC VIN "F"


Hope helps (remember rated and comment this).

Aug 31, 2010 | 1992 Eagle Talon

1 Answer

Head gasket job

wow .. nice mechanic ...

Dec 17, 2008 | 1992 Mercury Grand Marquis

1 Answer

My jag xj sport v8 3.2 will not start

give the battery a full charge....un clip the air filter housing and leave it resting in place, put your foot to the floor on the gas pedal and keep cranking til it starts up,dont release the ignition key til it fires up,it will pop and bang and then when it fires up will smoke for a little bit (couple of mins) and then it will be fine.
If that doesnt work you will have to remove all 8 plugs,clean them,pour about 2 teaspoons in each cylinder before replacing plugs then do the same as above.
What happens with these engines is the cylinders get a bit too much fuel in them and it washes the oil away down the bores thus losing comression so it wont start.Instead of starting it up and switching it off briefly,let it run a bit and then give it a little rev before switching off...hope this helps

Dec 03, 2008 | 2006 Jaguar S-Type

1 Answer


What the firing order for a 92 Eagle Summit with a 2.4 Mitsubishi

Jul 30, 2008 | 1992 Eagle Summit

Not finding what you are looking for?
1992 Eagle Talon Logo

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts


Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Stewart Dibbs

Level 2 Expert

361 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides