Question about 1993 GMC Sierra K2500

Open Question

1993 GMC 2500 6.5 diesel, looking for a diagram to tell which of the fusible links goes to what, there are 7 and I know 1 goes to the underhood light, any ideas? Thanks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: 04 Tahoe blowing fusible link in fuse box for starter

HI...
ON the fuse box cover.
IS there a especification for the funtion of the fuse. or the number of the location of the fuse.
If you can give me, I can try help you. as more I can.

Thank you for use fixya.

Posted on Jul 24, 2008

Ad
  • 462 Answers

SOURCE: I need to replace the fuel filter on my 2003 GMC

ITS A SPIN ON FILTER, YOU NEED TO DISCONNECT THE WATER SENSOR ON THE BOTTOM OF THE FILTER, THEN USING A STRAP FILTER WRENCH LOOSEN THE FILTER AND SPIN IT OFF.

CHECK THE FILTER HOUSING TO BE SURE THE INNER FILTER SEAL ISN'T ON THE HOUSING AND CAME OFF WITH THE FILTER.

REMOVE THE WATER LEVEL SENSOR AND DISCARD THE SEAL.

INSTALL THE WATER LEVEL SENSOR ON THE NEW FILTER. USING A LITTLE GREASE ON THE INNER FILTER SEAL AND ON THE OUTER O-RING TO HOLD IT IN PLACE, SPIN ON THE NEW FILTER.

OPEN THE VENT ON THE UPPER SIDE OF THE FILTER HOUSING. PUSH DOWN ON THE HAND PUMP QUICKLY UNTIL THE FUEL IS COMING OUT OF THE VENT. CLOSE THE VENT AND PUMP THE FILTER PUMP UNTIL IT FEELS SOLID. AT THIS POINT START THE ENGINE. IF IT STALLS PUMP IT UP AGAIN AND RESTART THE ENGINE. IF YOU HAVE AN ASSISTANT THEY CAN PUMP THE FILTER PUMP WHILE THE ENGINE IS RUNNING AND QUIT WHEN YOU FEEL THE ENGINE IS NOT GOING TO STALL. ABOUT 10 TO 15 SECONDS USUALLY WORKS.

CHECK FOR LEAKS.

BEFORE STARTING THE ENGINE USE BRAKE WASH TO REMOVE THE FUEL SPILLED DURING THE FILTER REPLACEMENT. ALLOW IT TO DRY BEFORE STARTING THE ENGINE.

RATE ME PLEASE.

Posted on Jul 07, 2009

  • 290 Answers

SOURCE: Need diagram for serpentine belt 97 GMC serria

go to 2carpros.com. look at column on your left;click on belt routing diagrams, follow the pages and there it is. good luck!

Posted on Sep 03, 2009

bschilz
  • 2049 Answers

SOURCE: 2006 Dodge diesel belt routing diagram

Here's a link to the diagram you need...

http://www.gates.com/common/part_locator/view_diagram.cfm?id=S8023

Posted on Sep 23, 2009

Testimonial: "Awesome! thank you so much for the quick response!"

  • 83 Answers

SOURCE: 2006 Dodge Ram 2500 diesel truck----need inside fuse box diagram

If you are looking for the fuse box diagrams or any other diagrams for your Ram, check promanuals.net for a factory service manual for around 20 bucks or so. It's an invaluable tool for my Ram 2500.

Posted on Sep 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1996 ford e150 new alternator good battery but won't charge was charging but quit is there a fuse or relay


There are a couple of fusible links and a regulator fuse . G 60amp located in the underhood fuse box. Is the charge indicator lit on the instrument cluster ? The fusible links connect at the starter relay on righ inner fender . Do you know what a fusible link is and what it looks like ? New alternator ? aftermarket or ford replacement ? Check for B+ voltage at wires on the alternator , to see which have B+ voltage look at wiring diagram at http://www.bbbind.com/free_tsb.html Enter vehicle info. yr . make , model , engine etc... System click engine , then charging system under subsystem . Click search . then click blue link .

Jan 08, 2017 | Ford E-150 Cars & Trucks

1 Answer

Where is the ignition switch fuse located on a


Most cars do not have a fuse for the ignition switch itself. Power goes directly from the battery to the switch. Everything after the switch is fused. It might have what is called a fusible link which is a pc of wire that melts off if the current draw is too high. Try to find a wiring diagram for your car on line and it will tell you if it has a fusible link

Oct 20, 2014 | 1993 Chevrolet Lumina

2 Answers

How remove f link from fuse box in 97 corolla


Hi. The fusible links are the big fuses located in the fuse box. The exact location of the fuses depend on the engine and on the version of the car. In 1997 Toyota built series
7 Corolla. At the end of 1997 Series 8 was introduced. in the year 1997 both models with different engines were distributed. There are up to 4 fusible links (big fuses ranging from 30 Amp towing protector to 100 Amps) See here.
Low amps fusible links are also in passenger compartment.
The fusible links are simply fuses and can get replaced using long nose pliers.

Below I have published the fuse diagrams covering Toyota series 7 (1993 to 1997) models.

The fusible links can be purchased here.
The site also includes schematics.

In case the car is a series 8 (late 1997), here service manual for series 8.

ginko_139.jpg

Here a fuse link for Corolla 1997, color may vary depending on amps, the one below is low amp current 30A, 100A is usually blue and 40A green, there may be black fuses with no color code:

ginko_140.jpg

Aug 27, 2011 | 1993 Toyota Corolla

1 Answer

Need diagram for 1993 gmc sierra 2500 truckfiring order


4.3 (VIN W AND Z) ENGINES= 1-6-5-4-3-2 --DISTRIBUTOR ROTATION: CLOCKWISE

5.0 (VIN H AND M), 5.7 (VIN K AND R), 7.4 (VIN N AND J) ENGINES
1-8-4-3-6-5-7-2 ---DISTRIBUTOR ROTATION: CLOCKWISEmichael_cass.jpg

May 23, 2011 | 1993 GMC Sierra C2500

2 Answers

1993 rodeo not running no power to fuel pump


if there is no power to the fuel pump check relays and fuses....UNDERHOOD FUSE & RELAY PANEL IDENTIFICATION Fig. 2: Underhood Fuse & Relay Panel Identification Courtesy of ISUZU MOTOR CO. Fusible Link Identification ? A - 80 Amp (1991-92 3.1L) ? A - 60 Amp Main-1 ? B - 30 Amp Main-2 ? C - 30 Amp (1993-94) ECM (3.2L) ? D - 30 Amp Condenser Fan (A/T Models) Relay Identification ? 1 - Headlight Relay ? 2 - A/C - Heater Relay ? 3 - Starter Relay ? 4 - A/C Compressor Relay ? 5 - Charge Relay ? 6 - Fuel Pump Relay ? 7 - ECM Relay ? 8 - Wiper Relay Fuse & Circuit Breaker Identification ? 1 - 15 Amp (1991) ECM, Fuel Injection System ? 1 - 15 Amp (1992-94 2.6L) ECM, Fuel Injection System ? 1 - 10 Amp (1992-94 3.1 & 3.2L) Heated Oxygen Sensor, Fuel Injection System ? 2 - 20 Amp (1991-92) Fuel Pump ? 2 - 20 Amp (1993-94 2.6L) Fuel Pump ? 2 - 15 Amp (1993-94 3.2L) Fuel Pump ? 3 - 10 Amp (1991) ? 3 - 15 Amp (1992-94) Turn Signal Lights, Hazard Warning Flasher Lights ? 4 - 10 Amp Horn, Door Locks ? 5 - Not Used (1991 3.1L) ? 5 - 10 Amp Charging System, Charge Warning Light WARNING: Always disconnect battery ground cable before servicing "high- current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician. Page 1 of 2 FUSES & CIRCUIT BREAKERS -1994 Isuzu Rodeo LS? 6 - Not Used (1991) (1992-93 2.6L) ? 6 - 10 Amp (1992-94 3.1L & 3.2L) A/T Interlock System ? 6 - 10 Amp (1994 2.6L) Heated Oxygen Sensor, Fuel Injection System ? 7 - 20 Amp Heater/Air Conditioning Blower Controls ? 8 - 10 Amp Air Conditioner Compressor Controls ? 9 - 10 Amp Right Headlight ? 10 - 10 Amp Left Headlight © 2008 Mitchell Repair Information Co., LLC.
62217_isuzfuse_1.jpg
Underhood fuse block swap out relay #7 thats the ECM relay.
Ground Circuits Using a DVOM, touch negative voltmeter lead to a good ground. Touch positive voltmeter lead to each ground terminal. With vehicle running, voltmeter should indicate less than one volt. If reading is greater than one volt, check for open, corrosion and loose connection on ground lead. See ECM GROUND LOCATION table for ECM ground location.
Page 1 of 1 SYSTEM/COMPONENT TESTS - 2.6L EFI -1994 Isuzu Rodeo

Mar 28, 2010 | 1993 Isuzu Rodeo

1 Answer

Need diagram for serpentine belt 97 GMC serria 2500 6.5L Diesel w/ AC


go to 2carpros.com. look at column on your left;click on belt routing diagrams, follow the pages and there it is. good luck!

Sep 03, 2009 | 1997 GMC Sierra

1 Answer

Need help replacing fusible link connector


It doesn't matter because they all carry +12V to the respective circuits. What does matter is which fusible link goes to which circuit (assuming they are different) but if you didn't cut them off, then they should still be connected to the correct circuits.

Jun 24, 2009 | 1994 GMC Safari

1 Answer

Duramax in a 1993 2500


sure if you have all the computers and wire harnes.

Oct 13, 2008 | 1993 Chevrolet C/K 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...