Question about 1995 Ford F150 Styleside Regular Cab

1 Answer

I have a 1995 F150 4x4 with a 5.0 that caught fire right at the master cylinder (or that area). It didn't burn everything just a few wires and parts on the firewal and fenderwell. I just need a picture or something showing me what wires and parts are on that side of the engine compartment so that I can replace them. I have bought the Haynes repair manual but it doesn't have a blown up picture or anything showing me what's there. Any help would be greatly appreciated.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 424 Answers

Check to see if the 05s28 recall was performed. There is a recall to inspect the speed control deactivation switch on the master cylinder for leaking causing a fire. Contact Ford if the switch was the cause of fire. Good luck.

Posted on Nov 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi- 1995 jeep wrangler 2.5yj- clutch grinding won't go into gear - seems full of fluid but over filled it works good for a few months -does it again- repeated -works good-maybe master slave problem ?


1995 YJ if still stock all that is ONE PART, see FSM quote below.
is the fluid dropping, day by day, week by week???
y/n?
yes, then either the slave or mc are bad.
sometimes both can fail, (rust happens inside and is progressive)
what I do , is this. (if not wanting to change out both)
1: look at the MC, if it done leak down either side of the fire wall
it might be good (dont mean the piston seals good but its not leaking, so if fluid drops , (every week say) the the MC is ok
and for sure the slave leaks.

2: so where is your slave. have you looked,? (swaps happen)
most leak and can not be detected as that leak landed on the road to work.
for sure its just 2 parts, here, you know the clutch is ok.
because it works with fluid in the system and bled.
now ILL PASTE THE FSM words out of a real factory service manual.
they are clear.
FSM words, QUOTE:
CLUTCH HYDRAULIC LINKAGE REMOVAL
The clutch master cylinder, slave cylinder
and connecting line are serviced as an assembly
only.
The linkage components cannot be
overhauled or serviced separately. The cylinders
and connecting line are sealed units. Also
note that removal/installation procedures for
right and left hand drive models are basically
the same. Only master cylinder location is different.
(1) Raise vehicle.
(2) Remove fasteners attaching slave cylinder to
clutch housing.
(3) Remove slave cylinder from clutch housing (Fig.
9).
(4) Disengage clutch fluid line from body clips.
(5) Lower vehicle.
(6) Verify that cap on clutch master cylinder reservoir
is tight. This is necessary to avoid undue spillage
during removal.
(7) Remove clutch master cylinder attaching nuts.
Note that one nut is accessible from engine compartment
and one nut is accessible from under instrument
panel (Figs. 10 and 11).
(8) Remove clip securing clutch master cylinder
push rod to pedal and slide push rod off pedal pin.
(9) Disconnect clutch pedal position switch wires.
(10) If pedal pin is equipped with bushing, inspect
condition of bushing and replace it if worn or damaged.
(11) Remove clutch hydraulic linkage through engine
compartment.

Dec 02, 2016 | Jeep Cars & Trucks

1 Answer

ABS caught on fire


Typical of wire shorting out against the metal frame. Simply replace the burnt wire and you should be good to go.

Dec 06, 2013 | Cars & Trucks

1 Answer

I have changed the brake lines and the Master cinlender on my 1995 Lincoln town car , I have bleed the cinlender and the brake lines and still no brake what am I doing Wrong.


air leak at a connection or air still in brake lines. provided the brake master cylinder was installed right and proper vacuum is reaching the master. or a faulty master cylinder from the parts store. those are the only possible options. hope this helps, good luck

Mar 13, 2012 | 1995 Lincoln Town Car

2 Answers

I have a 1997 f150 ext. cab the other evening we were cooking out when we heard a muffled exsplosion luck haven it we were just up the drive from my truck. welooked toward the truck and we could see smoke...


You might want to contact Ford. There was a class action lawsuit regarding bad brake pressure sensor that caught fire. Gentleman in Iowa died in garage fire attributed to defect. Might want to contact a lawyer.

Mar 21, 2011 | Ford F-150 Cars & Trucks

2 Answers

Brake pedal goes to the floor under constant presure. New wheel cylinders, vacuum boost, master cylinder, shoes. Everything bled, and no leaks anywhere. Any thoughts?


DID you bleed in this sequence.... Right rear wheel, left rear wheel, right fron wheel, left fron wheel, ABS hydralic fittings, & finally the Master clyinder? If not you will have air in the lines

Dec 18, 2010 | 1995 Ford F250

3 Answers

Need to know were gas filter is thanks bill riley


For 1995 Toyota Corolla 1.8L EFI DOHC 4cyl the Fuel Filter is located under hood, driver side, rear engine area, passenger side of master cylinder, mounted in fuel line.

Good luck.

Mar 22, 2010 | 1995 Toyota Corolla

1 Answer

Master Cylinder replacement on 1995 Oldsmobile 88


Start with right rear then left rear,then right front then lft front,Would rebleed at master cylinder 1st.

Jun 18, 2009 | 1995 Oldsmobile Eighty Eight

3 Answers

Low / Soft Clutch Pedal, 1995 Rodeo 2W 2.6L


my rodeo had the same problem i corrected it by bleeding the slave cylinder. and is located on the driver side on the gearbox you will find it if you follow the line from the master cylinder down to the gearbox and if that helps but happens again it might have to be replaced.

Aug 01, 2008 | 1994 Isuzu Rodeo

Not finding what you are looking for?
1995 Ford F150 Styleside Regular Cab Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...