Question about 1999 Ford Explorer

1 Answer

Power windows will not work, i replaced the power switch control on driver door. still will not operate. i am not sure which fuse controls the windows

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 19,396 Answers

Hi.

Disconnect the battery and access the power distribution box, located in the engine compartment.

Inside the box you will find a 30Amps box in location # 4, that is the fuse for the power windows and electric roof.

Check also the fuse box behind the dash , there is a 7.5 amp fuse in location # 12, this controls power window relay, washer pump relay.

Power window relay and switches must also be tested.

Regards.

Posted on Nov 14, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: rear doors & windows

Check to see if you have child protection locks on them if that is the case turn them off? Please rate my response Thank you very much

Posted on Jan 29, 2009

  • 295 Answers

SOURCE: power windows only operate from the driver master

Check the ground circuits. Find out what wires are the ground suppllies. take a 12 volt test light from battery positive and probe the circuit if it lights up the ground is good is it does not bad ground. I would first check the wires in the door jam. where the harness from the car goes into the door. pull back the rubber cover I have seen tons of wire get damaged in there from the door opening and closing all the time. hope this helps.

Posted on Aug 01, 2009

  • 221 Answers

SOURCE: 1999 Olds Intrigue electric windows

The switch could be bad or needs to be cleaned.

Posted on Mar 12, 2009

468 Chevelle
  • 81 Answers

SOURCE: window switch for driver control and passenger switch window

sounds like you have a passenger window motor problem. Try hitting the right door panel hard, down near the speaker opening and pushing the switch at the same time. If it moves, the motor windings are and needs to be replaced.

Posted on Mar 26, 2009

  • 34 Answers

SOURCE: power locks and windows controls not working on

there are also fuses under the hood did you ck those also,

Posted on Oct 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power windows wont roll up or down on 2006 Cadlliac cts


With the electronic's involved ,your best bet would be to take to a qualified repair shop . The door 's have electronic control module inside that control door lock's an window operation . Hooking up a professional or factory scan tool an viewing input data an checking DTC'S - diagnostic trouble code's would be the first step any professional technician would do . You probably have no idea what these are ? Messing with these systems can render your vehicle unuseable if you do not know what you are messing with .

Power Windows System Components
The following components are used to control the power windows:
• Driver door module (DDM)
• Passenger front door module (PDM)
• LH rear door module (LRDM)
• RH rear door module (RRDM)
• Driver door switch assembly (DDSA)
• RH front power window switch
• LH rear power window switch
• RH rear power window switch
• LH front power window motor
• RH front power window motor
• LH rear power window motor
• RH rear power window motor
• Class 2 serial data link
• DR MOD PWR C/B 30 Amp circuit breaker
• DRIVER DR MOD 10 Amp fuse -- DDSA and DDM logic, DDM internal driver operation.
• PSGR DR MOD 10 Amp fuse -- PDM logic and internal driver operation.
• REAR DR MOD 15 Amp fuse -- LRDM and RRDM logic and internal driver operation.
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a power window switch built into the driver door switch assembly (DDSA) , or, from a power window switch mounted locally on its associated door. The driver door window can be operated only from the driver door power window switch built into the DDSA.
When the driver door module (DDM) receives a driver door window switch request from the DDSA, the DDM examines the request and inspects to see if it has received any messages from any of the other vehicle modules prohibiting the movement. If no prohibitive messages have been received, the DDM then applies power and ground to the driver door window motor to move the window as requested.
When a passenger door module, passenger front door module (PDM), LH rear door module (LRDM), or RH rear door module (RRDM), receives a window switch request from, either the DDSA or the window switch mounted locally to its door, the passenger door module examines the request and inspects to see if it has received any messages from any of the other vehicle modules prohibiting the movement. If no prohibitive messages have been received, the passenger door module then applies power and ground to its associated window motor to move the window as requested.

So do yourself a favor an take it to a qualified repair shop.

Nov 22, 2017 | Cars & Trucks

1 Answer

Diagnosing rear windows not working on a 02 Bonneville


Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door power window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally on its associated door. The driver door power window can only be operated from the driver door window switch built into the driver door switch assembly (DDSA).
When the driver door module (DDM) receives a window switch request from the DDSA, the DDM checks the Class 2 serial data to see if the status information is correct (i.e. ignition switch position) to permit window operation to occur. If the status information is correct, the DDM, either supplies power and ground to its associated window motor, or, if the request is for one of the passenger windows, sends a command via the power door serial data circuit to the passenger door module (PDM, LRDM, or RRDM) controlling the window. The passenger door module (PDM, LRDM, or RRDM) controlling the window then supplies power and ground to its associated window motor to move the window as requested.
When one of the local window switches mounted on one of the passenger doors is operated, the associated door module examines the request and checks to see if there are any messages from the DDM prohibiting the movement. If conditions are correct, and no prohibitive messages have been received from the DDM, the associated door module then supplies power and ground to its associated window motor to move the window as requested.

Do you know about computer controlled windows and door lock systems ?

Each door module has its own battery positive voltage supply circuit to use for power window operation, but they are all fed by the same 30 amp power window circuit breaker located in the rear fuse block. Each door module also has a seperate ground circuit to use for power window operation. These circuits are in the same dedicated connector as the window motor control circuits of each door module and are used exclusively for window motor operation.
Each door module also has a battery positive voltage circuit and a ground circuit that are used to power up the module ,as well as, to control mirror and door lock functions. Battery positive voltage to the DDM is supplied through the DRVMDL 10 amp fuse located in the rear fuse block. Battery positive voltage to the PDM is supplied by the PASS MDL 10 amp fuse located in the rear fuse block. Battery positive voltage to both the LRDM and RRDM is supplied by the RRDR MDL fuse located in the rear fuse block. Ground for the DDM is provided through a ground circuit to G200. Ground for the PDM is provided through a ground circuit to G201. Ground for the LRDM is provided through a ground circuit to G302. Ground for the RRDM is provided through a ground circuit to G301.
Window Motors
Each door module supplies battery positive voltage and ground, through the window motor control circuits, to its associated window motor. The window motors are reversible. The direction the window moves depends on which motor control circuit the battery positive voltage is applied to, and which motor control circuit the ground is applied to.To move the window in the Up direction, the module applies battery positive voltage to the window motor Up control circuit, and ground to the window motor Down control circuit. When a window movement in the opposite direction is needed, the module reverses the polarity and supplies power and ground to the opposite circuits to move the window in the reverse direction.

Feb 04, 2017 | 2002 Pontiac Bonneville

1 Answer

How do you remove the right front door panel on a 2004 buick le saber


Did you test it or are you guessing just because it won't open or close ? How To Install Remove Front Door Panel Buick Lesabre 00 05 1AAuto com both right an left are the same .
Power Windows System Components
The following components are used to control the power windows:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Front Door Module (PDM)


?€¢
LH Rear Door Module (LRDM)


?€¢
RH Rear Door Module (RRDM)


?€¢
Driver Door Switch Assembly (DDSA)


?€¢
RH Front Power Window Switch


?€¢
LH Rear Power Window Switch


?€¢
RH Rear Power Window Switch


?€¢
LH Front Power Window Motor


?€¢
RH Front Power Window Motor


?€¢
LH Rear Power Window Motor


?€¢
RH Rear Power Window Motor


?€¢
Class 2 serial data circuit


?€¢
Power door serial data circuit


?€¢
PWR WDO 30 Amp Circuit Breaker


?€¢
DRVMDL Fuse (10 amp)


Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation


?€¢
PASS MDL Fuse (10 amp)


Front Passenger Door Module logic and internal driver operation


?€¢
RRDR MDL Fuse (10 amp)


Left Rear Door Module and Right Rear Door Module logic and internal driver operation


Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.

Oct 30, 2016 | Buick Cars & Trucks

1 Answer

Power windows dont work


There is a circuit breaker for power windows .
Power Window System Components
The power window system consists of the following components:
?€¢
Driver Door Switch (DDS)


?€¢
Passenger Door Switch (PDS)


?€¢
Body Control Module (BCM)


?€¢
Rear door power window switches


?€¢
Power window motors in each of the doors


?€¢
PWR WDO Circuit Breaker


Power Window System Controls
The power window system will operate anytime the Retained Accessory Power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The driver master control switches are integrated into the DDS. When a power window switch is activated in the up or down positions the DDS supplies power and ground to the window motor control circuits to drive the window motor in the required direction. Prior to activating a power window motor the DDS will supply the control circuit with a low current bias voltage in order to determine that a short to ground condition does not exist and during window motor operation the DDS continues to monitor the motor current to verify proper window motor operation.
The DDS controls the passenger window by a serial message to the PDS. When a power window switch is activated in the up or down positions the PDS supplies power and ground to the window motor control circuits to drive the window motor in the required direction. Prior to activating a power window motor the PDS will supply the control circuit with a low current bias voltage in order to determine that a short to ground condition does not exist, and during window motor operation the PDS continues to monitor the motor current to verify proper window motor operation. (Scan tool support is available for this system
Check this circuit breaker
RETAINED ACCSRY PRW BRKR 30 amp. located in the left instrument panel fuse box . if the breaker is good check power B+ at the drivers door switch . connector 1 terminal b yellow wire . Sometimes the wires inside the rubber boot coming from body to door break .

Oct 29, 2015 | 2005 Chevrolet Impala

2 Answers

Power windows stop working


start with the fuses replace it anyway or put a 12volt bulb in place of fuse , when its loading down it will shine bright , when normal it will not shine much at all.
be sure all connections to battery are working check for a second positive cable with a f useable link

May 03, 2015 | Cars & Trucks

1 Answer

Which Relay/Fuse controls the power windows?


Did you check for battery voltage at the switch , with a volt meter before you replaced the main driver door switch ? Maybe you'll want to take this to pro ,instead of just replacing parts !
Symptom Chart Condition Possible Sources Action
  • No communication with the smart junction box (SJB)
  • Circuitry
  • SJB
  • REFER to Section 419-10 .
  • A single power window is inoperative - driver front power window is inoperative/does not operate correctly
  • Power window motor regulator and motor
  • Circuitry
  • Window control switch
  • Smart junction box (SJB)
  • Go To Pinpoint Test A .
  • A single power window is inoperative - passenger front, left rear or right rear
  • Power window motor regulator and motor
  • Circuitry
  • Window control switch
  • Go To Pinpoint Test B .
  • All power windows are inoperative
  • Smart junction box (SJB) fuse 30 (10A)
  • SJB circuit breaker 10 (30A)
  • Circuitry
  • Delayed accessory relay
  • Battery saver relay
  • Driver window control switch
  • SJB
  • Go To
PINPOINT TEST C: ALL POWER WINDOWS ARE INOPERATIVE Test Step Result / Action to Take C1 CHECK FOR CORRECT OPERATION OF THE INTERIOR LIGHTS
  • Turn on the interior lights.
  • Do the interior lights operate normally?
Yes
GO to C2 .

No
To continue diagnosis, REFER to Section 417-02 . C2 CHECK CIRCUIT 400 (LB/BK) FOR VOLTAGE TO THE DRIVER WINDOW CONTROL SWITCH
  • Disconnect: Driver Window Control Switch C504b.
  • Key in ON position.
  • Measure the voltage between the driver window control switch C504b pin 4, circuit 400 (LB/BK), harness side and ground.
    >
  • Is the voltage greater than 10 volts?
Yes
GO to C4 .

No
GO to C3 . C3 CHECK CIRCUIT 400 (LB/BK) FOR AN OPEN OR SHORT TO GROUND
  • Key in OFF position.
  • Disconnect: SJB C2280c.
  • Measure the resistance between the driver window control switch C504b pin 4, circuit 400 (LB/BK), harness side and the SJB C2280c pin 17, circuit 400 (LB/BK), harness side; and between the driver window control switch C504b pin 4, circuit 400 (LB/BK), harness side and ground.
    >
  • Is the resistance less than 5 ohms between the driver window control switch and the SJB; and greater than 10,000 ohms between the driver window control switch and ground?
Yes
Go To Pinpoint Test H

No
REPAIR the circuit. TEST the system for normal operation.

Mar 24, 2015 | 2004 Mercury Sable

1 Answer

Power windows on automobile


Hey. This is very likely power window switch and second one would be a relay. Look in ovners manual which relay is responsible for your windows and or doors. Let me know if you can't check it out

Mar 14, 2017 | 1990 Acura Legend

1 Answer

The windows on my crv wont work


at all stations?
all fuses, in both boxes. (did you read the operators guide to find them,
some cars have a circuit break (thermal) for windows,
and is located in the fuse box.
all this info is at alldata.com
ill look. ill respond , as you are a pro DIY person, can read schematics. if not , its just a guessing game.
IT IS a FUSE, not a breaker. but each motor in door has CB.
UNDER HOOD 40am Fuse #13
then fuse 23 underdash and fuse 8 same.
then the relay.same place.
and the relay is controlled by, master station (drivers)
the driver location doesnt need the relay to work.
the relay feeds power to all other window controls
so the master station is unique.
log in to alldata.com and see the pages on power windows.
here are some tid bits.
battery pull warning

Resetting the power window control unit is required after performing the following procedures: Disconnecting the battery, Removing the No. 6 (7.5 A) and/or the No. 23 (20 A) fuses from the under-dash fuse/relay box or disconnecting the driver's door wire harness.
and
window relearn/reset.
Control Unit Reset
  1. Turn the ignition switch ON (II).
  2. Move the driver's window all the way down by holding the driver's switch firmly down; when the window reaches the bottom, hold the driver's window switch firmly down for 2 seconds.
  3. Move the driver's window all the way up by holding the driver's switch firmly up; when the window reaches the top, hold the driver's window switch firmly up for 2 seconds.
  4. If the window does not work in AUTO, turn the ignition switch OFF and repeat the procedure.
  5. Check the window and power door lock operations

Jan 12, 2014 | 2006 Honda CR-V

6 Answers

Windows won't roll down


Does the rear window work from the passenger switch?

Oct 07, 2009 | 2003 Cadillac CTS

1 Answer

2003 F250 Power Windows won't work


check fuses 35 & 41 (10 amp, red).
it also shows an accesory delay relay in the fuse panel.
And fuse 601? 30 amp.

make sure you don't have lock-out on driver switch panel activated.

Power Window System
Features and Operation
NOTE: The accessory delay feature will allow power window operation up to 10 minutes after the ignition is off or until a door is opened.
If equipped with power windows, the window control switch (14529):
  • will operate the power windows only when the ignition switch is in the RUN or ACC position.
  • is located on each front door trim panel, and Crew Cab and Excursion rear door trim panel.
  • may be used to raise or lower the driver side, passenger side and rear windows from the LF control on the driver side, or the passenger window from the passenger switch.
  • includes a one-touch down (OTD) feature for the driver door window.
  • can partially lower the driver side window when the LF window control switch is depressed half way (first detent).
  • will completely lower the driver side window when the LF window control switch is fully depressed and then released (second detent).
Power Window System — Modes of Operation
There are two modes of operation for the power window system.
Manual Mode
When the LH window control switch is pressed to the first down position, the window will move down until one of the following conditions are met:
  • The LH window control switch is no longer in the first down position.
  • The LH window control switch is pushed to the OTD position, causing the windows to enter auto mode.
Auto Mode
Auto mode provides the OTD feature. The OTD feature is activated when the LH window control switch, for the LH window, is pressed to the second down position.
Auto mode will be terminated when any of the following conditions are met:
  • The LH window control switch is pushed to the UP position.
  • The LH window control switch is released (OFF position) and then moved to the DOWN position (first detent) or OTD position (second detent).
  • Note: Delayed accessory feature must be active.
The OTD feature is controlled by the window control switch.

---------------------------------------------------------
Condition Possible Sources Action
  • All power windows are inoperative
  • Fuse(s).
  • Circuitry.
  • LF window control switch.
  • Accessory delay relay.

May 23, 2009 | 2003 Ford F250 Super Duty Crew Cab

Not finding what you are looking for?
1999 Ford Explorer Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...