Question about 1991 Peugeot 405

1 Answer

How do u adjust a handbrake cable on a 406 - 1991 Peugeot 405

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Peugeot Expert
  • 274 Answers

Raise and support rear of the car
there is a small metal cover that bolts over the handbrake adjuster

Posted on Dec 07, 2009

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 53 Answers

SOURCE: My 92 Honda Civic Handbrake cable broke one

um might work but not for a very long time

Posted on Jul 28, 2009

johnjohn2
  • 5763 Answers

SOURCE: how do get to and adjust handbrake cable on my 960 volvo

make sure e-brk shoe adjuster is all the way closed. then start adjusting little by little until you can slide disc back on and have a little friction when you spin it by hand, also hope your replacing dics, old one sometime have lots of rust stopping disc from going on anyway good luck and hope this helps.

Posted on Oct 20, 2009

Testimonial: "very fast, thanks "

  • 2309 Answers

SOURCE: how to adjust handbrake on a 2004 passat

a word of caution, before adjusting the parking brake make sure the rear adjustment is working and properly set up

Posted on Nov 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace my hand brake cable on my ford falcon XH ute


wait a bit ....is it rear disc or rear drums on that ute

will assume its under dash hand brake pull lever tyoe

the disc setup may have single cables for each rear
rear disk brake cable is approx $ 150

if your XH it is close to the XE and XF set up drums
a complete one line loop cable outer and inner
with plastic grommets along the back chassis rail ( they break )
so the one inner cable works both rear handbrake shoes


hand brake cable is a shorty

undo the adjustment thread
just below the hand brake cable point up somewhere above the gearbox
(drums )
after new cable fitted
drums are adjusted with the old school way with the handbrake adjuster tool
handbrake cable adjusted

then the handbrake handle when pulled out to hold needs14 plus clicks
comes out a long way for some weird reason
on drums
if cable adjustment is done wrong onrear drums the handbrake cable will come loose in the drum as you drive along

26261095-l1jraapkfcyxqeqgczv0cruv-4-0.jpg

26261095-l1jraapkfcyxqeqgczv0cruv-4-3.jpg

26261095-l1jraapkfcyxqeqgczv0cruv-4-5.jpg

Aug 17, 2016 | Ford Cars & Trucks

2 Answers

Handbrake adjustment citroen nemo


Remove the boot around the hand brake or pull it back to expose the adjustment nut and locking nut on the threaded cable end, turn it clockwise to tighten the handbrake cables.

Aug 09, 2016 | Citroen Cars & Trucks

1 Answer

1.9vauxhall vectra C fitted new pads and hand brake cable now handbrake has too much travel same as before items were fitted


it looks like a common flaw in design
it can fail an mot if handbrake wont hold
with both wheel of the ground and hand brake fully applied do the wheels spin

handbrake cable system on a
1.9vauxhall vectra C says self adjusting

but this picture implys there is an adjustment point
source
Thread Handbrake adjust


you tube vectra handbrake system in action

Opel vectra handbreak



26219124-ygof5331xb1wvnadk5rotqyb-1-1.jpg

Jun 15, 2016 | Cars & Trucks

2 Answers

Adjusting hand brake


there is a cable adjuster under the center console if its got a rear ashtray just pull that out and look there.but you should remove the rear brake drums and check the shoes. and the handbrake fulcrum levers, they can sieze up. also make sure the levers return to the stops with handbrake off and the auto adjusters are working ok before adjusting the handbrake cable! it helps brake performance if you give the auto adjusters a bit of a tweak before putting the drums back on. manually adjust 3-4 clicks or until the drum goes back without binding.

May 29, 2013 | 2005 MG ZR

1 Answer

Cant find handbrake adjuster for peugeot 207


Just fixed mine, the handbrake adjuster is attached to the handbrake lever inside the consul, remove the blanking plastic section to the left of the handbrake, near the driver seat, the with a torch see in side to base of handbrake lever, you will see a vertical rod with a 10mm nut (black) adjustment is done here, quater turn at a time. my problem was the rear 2 cables had falled out of the Tee bar at the back, remove the plastic blanking plate in the rear cup holder see 13mm nut, undo this allows the consol to lift slightly, re insert cables etc, i the tied the 2 cables together with cable tie to stop them popping of the tee bar, so far so good

Jan 01, 2013 | Cars & Trucks

2 Answers

My handbrake needs adjusting in my Toyota Corolla 1994. Can u please explain how this adjustment is done.


Hello, My usual Brands are Ford products, but Foreign cars usually use simple, less expensive ways to do things. Assuming the brake pads are good, there should be a cable connected to the handbrake. You would usually pull the handbrake up to engage about 1/4 the way to engagement and lock it there.
Then you would go underneath the car and find the cable that stretches from the handbrake lever to a juction with a second cable. There should be an adjusting thread somewhere at this intersection.

With the rear wheels off the ground, you would tighten the nut on the threads of the handbrake cable until you hear rubbing in the rear brakes. Then get inside the car and pull back on the handbrake lever and you should not be able to move the rear wheels with the handbrake set. You then release the handbrake 100% and the rear wheels should turn mostly without noise.

Now if you can not find an adjustment nut under the car, it is possible the handbrake adjustment nut is under the handbrake cover/boot inside the car. Still use the same process of setting the lever 1/4 engaged and tightening the threaded cable until the rear wheels start dragging.

I hope this helps you.

Sep 28, 2011 | 1994 Toyota Corolla

1 Answer

Ford bantam handbrake adjustment


remove the back brake drums ,slacken handbrake cable then run a mini grinder around the lip on the edge of the drum .Then adjust the auto adjusters manully so when the drum is push on it just goes on ,tap with a hammer all around the drum to level the shoes and if need be adjust up a bit more ,then when finished re-adjust the cable so you have three notches on handbrake lever

May 31, 2010 | 2006 Ford Focus

1 Answer

How to adjust handbrake cable


HANDBRAKE CABLE ADJUSTMENT

1. Raise the vehicle and release the handbrake.
2. De-adjust the handbrake cable.
  • Remove the locking pin.
  • Slacken the adjuster locknut.
  • Slacken the adjuster until the levers on the callipers have returned to their stops.
3. Paint alignment lines on the lever and caliper
4. Tighten the adjuster until the caliper levers move from the alignment lines.
5. Apply the handbrake to equalise the cable.
6. Tighten the adjuster locknut to a minimum of three clicks and a maximum of six clicks.
7. Fit a new adjuster locking pin.
8. Lower the vehicle.

Jun 04, 2009 | 2002 Toyota MR2 Spyder

1 Answer

Hand break no good,??? big job ??? or D I Y ??? sorry on Peugeot 406 diesel estate


If fitted with rear discs, the handbrake shoes inside the disc will probably need adjusting as these tend to be ignored during service.

Mar 17, 2009 | 1987 Peugeot Liberte

2 Answers

Volvo s40


The handbrake adjuster is under the centre console behind the lever. If its coming too high, check that the levers at the rear brake calipers are free and moving back to their stop position - they are prone to seizing up on older or little used cars. They can usually be freed off with a bit of lube and working the lever back and forwards. If that dosn't work, unfortunately you'll need new calipers. Do not adjust the handbrake cable unless the caliper levers are at their stops as this seriously reduces handbrake efficiency!

Jan 08, 2009 | 2000 Volvo S40

Not finding what you are looking for?
1991 Peugeot 405 Logo

Related Topics:

657 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...