Question about 1996 Chevrolet Beretta

1 Answer

1996 chevrolet beretta 2.2 l sfi ohv 4cyl i keep burn up alt. on the car and the + ter. that bolt up to the big post on the alt. is getting hot

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

This might not solve your problem but with the chevy beretta there is a fusable link(8 guage wire) that connects from the battery to the alternator. The wire is there so if there is a surge through the electrical system that fusable link gets burned and not your alt. If your alt. is getting burned up you possibly have a fusable link that is to big and is allowing to much surge go into the alt. I had the opposite problem with mine. I had a to small of a wire so the fuseable link kept burning up. We spiced it three times before it stopped burning up. I hope this helps

Posted on Feb 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crank shaft senser locacated @ on a 1995 chev beretta


On 1995 Chevrolet Beretta 2.2L SFI OHV 4cyl the Crankshaft Position Sensor is located under hood, passenger side, rear engine area,mounted on engine under intake manifold.

I hope this helps; remember to rating this and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment.

Have a nice day and thanks for using FixYa.
Jose.

Oct 17, 2011 | 1995 Chevrolet Beretta

1 Answer

Where is the crank senser located on a 1995 chev beretta


On 1995 Chevrolet Beretta 2.2L SFI OHV 4cyl the Crankshaft Position Sensor is located under hood, passenger side, rear engine area,mounted on engine under intake manifold.

Hope this helps, and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment. Have a nice weekend and thanks for using FixYa.

Jose.

Oct 14, 2011 | 1995 Chevrolet Beretta

1 Answer

Where is the computer located in a 95 beretta 2.2L


For 1995 Chevrolet Beretta 2.2L SFI OHV 4cyl the Engine Control Computer is located in front seating area, passenger side, behind dash, mounted on passenger side of glove compartment cavity .

Hope this helps (remember to rate this ansrwer)

Jan 10, 2011 | Chevrolet Beretta Cars & Trucks

2 Answers

1997 cavalier head gasket replacement with a 2.2. Also need the torque specs and sequence for the head bolts


Go onto Autozone.com and sign up for their online repair. It is free to use but you have to register.

Nov 16, 2010 | 1997 Chevrolet Cavalier

1 Answer

Engine torque specs for 1996 chevy cavalier 2.2l


For 1996 Chevrolet Cavalier 2.2L SFI OHV 4cyl the check the next Head Bolt Torque sequence...

------------ front | 8 4 1 5 9 | of | | engine | 7 3 2 6 10 | ------------

Step 1: torque long bolts 8,4,1,5, & 9 to 46 Ft/Lbs torque short bolts 7,3,2,6, & 10 to 43 Ft/Lbs
Step 2: torque all bolts an additional 90 degrees Recheck final torque in sequence

*** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

Hope helps (remnember rated this).

Jul 15, 2010 | 1996 Chevrolet Cavalier

1 Answer

Where is flasher relay located on 96 cavalier


For 1996 Chevrolet Cavalier 2.2L SFI OHV 4cyl, the Flasher is located front seating area, driver side, under dash, above kick panel, mounted in bottom of convenience panel.

2d9673f.jpg

Fig.: Turn/hazard flasher location-1996-00 vehicles

Hope helps with this (remember rated this help) TY for using Fixya.

May 27, 2010 | 1996 Chevrolet Cavalier

1 Answer

1996 gmc sonoma 2.2 engine


For 1996 GMC Truck Sonoma 2WD 2.2L SFI OHV 4cyl
The EGR Valve is located under hood, center, rear engine area, mounted top rear driver side of engine.

c30f299.jpg

Fig. 11: Unfasten the EGR valve retaining bolts...


b24c0c0.jpg


Fig. 12: ...then remove the EGR valve from the vehicle


I really hope help with this (remember rated and comment this post).


Mar 10, 2010 | 1996 GMC Sonoma

1 Answer

I need a diagram for a 1993 chevy beretta that will show me where exactly is fuel pump relay switch


1993 Chevrolet Beretta 2.2L SFI OHV 4cyl
The Relay - Fuel Pump is located under hood, passenger side, upper firewall, mounted in corner relay block.

Open the hood on the back firewall is a screw that takes off the plastic molding goes across the entire letgh of the fire wall. it comes off in two pieces behind this is the fuel pump fuse and relay switch.

Hope helped.

Feb 18, 2010 | 1993 Chevrolet Beretta

1 Answer

It does'nt heat ,I flushed heatercore,chaged thermostat,bled the radiator, car does'nt overheat. hoses to heatercore by firewall are cold other hoses are hot.


Need to check the valve that opens and closes the heater hoses and allows the water to travel to/thru the heater core. 1992 Chevrolet Beretta 2.2L SFI OHV 4cyl The Temperature Switch is located: Under hood, center, upper engine area, next to water outlet, driver side of block, mounted below coolant temperature sensor

Dec 07, 2009 | 1992 Chevrolet Beretta

1 Answer

I need to know the timing marks about a 98 cavalier 2.2


1998 Chevrolet Cavalier 2.2L SFI OHV 4cyl

2621f82.jpg

Fig. 1: The timing marks on the sprockets should be in alignment. If not, turn the crankshaft until the marks are aligned

c468191.jpg

Fig. 2: The timing chain tensioner is retained by a Torx head bolt (1) and a regular hex head bolt (2)

a5bfd58.gif

Exploded view of the timing chain and sprockets-2.2L OHV engine
( Where A = Timing Marks ).

I hope help you with this, good luck (remember rated this help).

Sep 16, 2009 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1996 Chevrolet Beretta Logo

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...