Question about 1997 Chevrolet Blazer

1 Answer

Just changed distributor cap and rotor, plugs and wires, Ignition control module, and coil on a 91 balzer. It ran after new parts, but stalled, and won't start agian. no spark form distributor to plugs. All of the plugs and wires work, tried 3 caps, and 2 rotors

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 399 Answers

Check the gaps on plugs also distributor also condensor in distributor

Posted on Nov 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Ignition mystery! 1994 GMC Suburban 2500 5.7 mtr. No spark to spark plugs. Have spark from coil to distributor. Have changed coil wire, cap, rotor, ignition module, and coil. have 12.5 volts going to...


I guess you could have the ignition analyzed on an oscilloscope. Maybe a tech could see something then.
I always heard the only gap was the spark plug gap-the rotor has no gap-are you sure you got the correct rotor? And does it touch the top distributor cap coil wire tower?

Let us know. It is a mystery worthy of a solution.

Sep 21, 2013 | Chevrolet Suburban 2500 Cars & Trucks

1 Answer

I am not getting any spark in my ignition system from a 1991 capri xr2. I have changed the coil, rebuilt the distributor, changed the cap and rotor button, and changed the spark plugs and wiring. It ran...


Did you replace the igniter (inside the distributer) and the ignition control module (on top of the distributer. Sometimes the control module gets overlooked...

Nov 09, 2010 | 1991 Mercury Capri

1 Answer

My 2003 gmc v6 just had its plugs and wires and distributor cap and button changed and i put the distributor button on wrong, it ran fine 4 a mon. or 2 and one of the screws came out of the button and...


The distributor cap and/or the ignition rotor most likely have a crack somewhere and the distributor cap should be replaced along with the ignition rotor. The ignition module could have been damaged as well as the ignition pick-up coil/stator and if replacing the distributor cap and ignition rotor does not solve the problem then the ignition module or the pick-up coil/stator assembly inside of the distributor is also most likely damaged and the distributor will need to be replaced. There is a certain procedure for removing and replacing the distributor, and the ignition timing is not adjustable and it is not set using a timing light or with the engine running, and if you do have to replace the distributor Let me know if you require the procedure to properly remove and replace the distributor or if you require any further assistance.

Aug 17, 2010 | 2003 GMC Sierra 1500

1 Answer

1999 silverado 4.3 cranks but no start can hear fuel pump, swaped out coil and crank sensor w/ known good parts no change, engine did start once after coil was changed ran rough and stalled and wont...


First check to see if full battery voltage is even getting to the "Pos" (+) positive side of the ignition coil when the key is in the "Run" position, and also that full battery voltage is getting through the "Pos" (+) or positive side of the ignition coil and over to the distributor ignition module

The ignition module and the pick-up coil/stator located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil, and a faulty ignition module can cause any one of these systems to malfunction.

That does sound like a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores. If the ignition module does test out alright then the problem could still be in the pick-up coil/stator, (it can be tested using an ohm meter by dis-connecting the wire connector from the pick-up coil/stator and the ohm reading between the two wires from the pick-up coil/stator should be between 500 and 1500 ohm's, and both of the wires from the pick-up coil/stator should show an open loop or an infinite reading between each wire and ground) and if the pick-up coil/stator is found to be faulty then replace the entire distributor, or the distributor will have to be dis-assembled to install a new pick-up coil/stator.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

To replace the distributor follow this procedure;

The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.

There is a mark or notch on the distributor housing that the rotor should be pointing to when the engine is on top dead center. This "static" timing is all that matters and the computer will be able to control the timing as long as the ignition rotor is in that position when the engine is at top dead center.

Removal;

1. With the engine at top dead center.

2. Look under the distributor cap and find where the number one terminal runs under the distributor cap, and where that position on the distributor cap corresponds with the distributor housing, and it should match up to a mark or a notch on the distributor housing indicating the number one position.

3. With the engine on top dead center the ignition rotor should be pointing to the number one mark or notch that is on the distributor housing, Then make a reference mark of the position that the ignition rotor is pointing to (out on the engine or firewall) and the more precise you mark the position, the easier the installation of the new distributor will be. This will be reference mark #1.

4. Remove the distributor lock down bolt, (the lock down clamp will most likely be attached to the distributor and if so it should not be removed from the distributor) then slowly lift up on the distributor about three inches and note the direction that the ignition rotor turns, and when the ignition rotor stops turning then mark the position that the ignition rotor is pointing to (out on the engine or firewall) and then lift the distributor striaght up and out, and remove the gasket or any left over gasket material from the intake manifold. The more precise you mark the position the easier it will be to install the new distributor and an assistant might be helpful. This will be reference mark #2

Once the distributor has been removed it is important that the engine does not get cranked over by the starter or the crankshaft turned at all, or the reference marks will become useless.

Installation;

Be sure that the new distributor is complete with a new module and that there is a new gasket in place on the distributor.

1. Lower the distributor with gasket down into the distrbutor well and align the ignition rotor with the #2 reference mark and when the distributor gear engages the drive gear on the camshaft then the ignition rotor should turn to the #1 reference mark as the distributor sets all the way back down flush on the intake manifold.

2. Install and tighten the lock down bolt, and If the distributor is properly installed then the ignition rotor should be pointing to the #1 reference mark and the #1 position on the distributor housing with the engine on top dead center.

Replace the distributor cap and connect the spark plug wires, and see if the engine will start, if the engine does start and the check engine light does not come on (assuming that it was not on before) then the distributor is properly installed and there is no further timing requirements.

Let me know if you require any further assistance.



a4e111e.jpg

71a37c7.jpg

91bcf9e.jpg

Jul 31, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

1989 GMC engine turns great , no spark at coil or plugs, had coil tested and repalced- new rotor and cap. not sure where to go next


Check your fuses (ECM) and also recheck your wire leads to the coil. Your ICM (ignition control Module) may also be bad, it's located in your distributor under the rotor. You can have that tested also to make sure it's working 100%, there common to go bad from corrosion caused by condensation under the distributor cap.
Thank you for using Fixya and good luck.

Mar 20, 2010 | 1989 GMC K1500

4 Answers

I want to replace spark plugs (8) and wires on my '84 GMC pickup


get a 20 dollar haynes or chiltons manuel and find the module and coil. always change the ignition module and coil every 4 no more than -5 years to be safe.

Feb 10, 2010 | GMC Sierra 2500 Cars & Trucks

5 Answers

1988 chevy 350 problem


The crank angle sensor maybe bad. It sends a signal to the computer so the spark plugs fire up.

Sep 09, 2009 | Cars & Trucks

2 Answers

No spark, just put in a new coil, distrbutor isnt dirty or wet, sombody told to check out the littl box's on the fender well, what are these to box's and what is there purpose? Mike 77 cj-5 304 3spd I...


I had the same problem with my 85 cj7 this week, I relpaced the ignition control module, plugs, wires, cap, rotor and the the coil; still had no fire to plugs. the problem turned out to be my distributor, replaced it today and she fired right up. Most likely it was the pick up module in the distributor that went bad.

Nov 30, 2008 | 1983 Jeep CJ7

Not finding what you are looking for?
1997 Chevrolet Blazer Logo

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...