Question about 1999 Dodge Durango
That is quite a labour intensive job..i know when i worked for a dodge dealership we charge out 10 hours and it would take every bit of that...please keep in mind, that's with air tools too and everythin available to you...maybe this one is best left with the experts...
Posted on Nov 14, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Location of heater core
It is under the dash in the middle of everything. You have to fully tear down the dash. allow at least 8 hours and also get a camera and take a lot of pictures. You can put parts in zip-lock bags and lable as you go.
You can get great info on dodgeforum.com
Posted on Sep 19, 2008
SOURCE: 1999 dodge durango heater core
It's a big job. Drain the coolant down, recover the freon in the ac system and disconnect the lines and heater hoses. Lower the steering column, remove the instrument panel assembly, remove the heater housing. Split the case halves on the housing and there you are. Usually around 500 to 700 dollars at a dealership.
Posted on May 29, 2009
This is provided you have confirmed that a plugged or partially plugged heater core is your problem, and not a vacuum problem, or heater control valve or similar is not defective. Yes it certainly sounds like some blockage/restriction there, but may I advise you to try this first, as it may save a lot of money, time, & aggravation. Go to Rona, Home depot, or similar hardware store & buy a drill pump. (about $25.00 in Canada) but there are cheaper ones around.
Remove your heater hoses at the firewall (when engine cold) and you will see the 2 copper ends of your heater core to attach drill pump to. Put one end of the pump (pressure side) on one fitting, of the core and the other hose from pump suction side, into a jug of CLR (calcium ,lime, rust, remover.) The other connection/fitting from your heater core will need a piece of hose going from it, into a pail, or another jug, same size as CLR to retrieve liquid when it flows through. Circulate the CLR through the core a few times, then let it sit in the core for a while. Then reverse the hoses at the core & circulate it through the other way a few times & let it sit in there as well. I let mine fill the core, then I plugged line where CLR would flow out of heater core & then let it sit all night in there to dissolve as much calcium etc., inside as it could. Then next day, I ran pump in both directions/fittings, again to flush everything out. Then I re-attached my heater hoses. My heat increased at least 75% at idle, because it had removed a lot of the restriction in the core.
Make sure you take all safety precautions, such as eye protection in case CLR splashes in your eyes, and make sure engine is cool, pressure is relieved via removal of rad cap & to avoid burn from hot coolant when hoses removed. My guess is that your into $20-$25 tops, and a whole lot less work. Let me know how it goes.
Posted on Oct 05, 2009
Tips for a great answer:
Oct 21, 2015 | 1999 Dodge Durango
Jan 23, 2011 | 1999 Dodge Durango
Dec 18, 2010 | 1998 Dodge Durango
Feb 17, 2010 | 1999 Dodge Durango
Dec 09, 2009 | 2000 Dodge Durango
Sep 28, 2009 | 1999 Dodge Durango
Aug 24, 2009 | 1999 Dodge Durango
May 29, 2009 | 1999 Dodge Durango
540 people viewed this question
Usually answered in minutes!