Question about 1997 Chevrolet Cavalier

2 Answers

Need location of thermostat ,over heating.

Need location of thermostat on 2.2 motor.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

On the 2.2 engine it is located on the lower radiator hose water pump side.

Remove the two retaining bolts for on the housing
Separate the housing halves to access the thermostat
Pull the thermostat out to remove it from the housing
The thermostat has an O-ring which goes around the center
Thoroughly clean the mating surfaces of the thermostat housing

When adding coolant, it is important that you use GM Goodwrench DEX-COOL® (orange colored, silicate free) coolant meeting GM specifications. On these vehicles, if silicate coolant (green) is added to the system, premature engine, heater core or radiator corrosion may result. In addition, the engine coolant will require change sooner; at 30,000 miles or 24 months.

Good luck and hope this helps.


Posted on Nov 14, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 312 Answers

If you follow the top hose from the radiator to the motor you'll notice a housing where the hose meets the motor. Disconnect the hose and remove the two bolts holding the housing in place. Remove the housing and the thermostat is underneath. When you replace it make sure the old gasket is completely removed and replaced with a new one. If pieces of the old gasket remain you will nto get a good seal and will eventually end up with leaks.

Posted on Nov 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Are there two thermostats for a 2012 Chrysler 200 with a 2 .4ltr engine and where are they located


There are two separate thermostats in your application, a primary and a secondary. The primary and secondary thermostats have different temperature profiles in terms of their opening temperature because they are located on different areas of the engine. The primary thermostat is located on the front of the water plenum in the thermostat housing/coolant inlet. The secondary thermostat is located in the cylinder head under the water plenum. The adapter that you are referring to does exist and I believe it is associated with the secondary thermostat.Here is a link to the first one. https://www.autozone.com/cooling-heating-and-climate-control/thermostat/duralast-thermostat/335455_381037_13514_93207 Here's the second thermostat. https://www.autozone.com/cooling-heating-and-climate-control/thermostat/duralast-thermostat/335477_381036_1620_93207

Nov 23, 2017 | Chrysler Cars & Trucks

2 Answers

No heat


If you have no heat in your vehicle then it is probably the heater core which is just a small radiator that sits behind the glove box. The thermostat itself is probably located where your top radiator hose connects to your engine. It is an easy and cheap fix, just pull the hose away after undoing the clamp and you should see it. If it is not there, then it will be in the bottom hose. Hope that helps you out.

Apr 20, 2013 | 1997 Buick LeSabre

1 Answer

Where is the thermostat located?


Follow the top raditor hose to motor. Sometimes it following bottom. But some of time its following the top.

Feb 11, 2012 | 2006 Buick LaCrosse

1 Answer

Does not blow hot air in the heater setting.


the two easiest things that are the most common cause of no heat are: 1 be sure you have plenty of coolant in the radiator, 2 it may be a stuck thermostat, if the coolant is full i would go ahead and change the thermostat, follow the top radiator hose to the engine, this hose will end at the waterneck, the thermostat is located in the waterneck, usually secured to the intake manifold with 2 bolts, remove these 2 bolts and gently pry the waterneck off, the thermostat will just sit in this opening, be sure to put the spring side of the thermostat down (facing the motor), use a new waterneck gasket when reassembling, this should solve your problem

Jan 22, 2011 | 2003 Chevrolet Impala

1 Answer

Econoline ford 1997 blower works fine but no heat


If the engine is getting warm, then you have one of 2 problems. First is a warm/cold air door motor located under the dash. Second would be a clogged heater core that would need flushed. If your motor is not getting warm then you need to replace your thermostat.


Ptake a moment and rate my answer ............Thanks

Dec 01, 2010 | 1997 Ford Econoline

2 Answers

Replace thermostat. Engine temperature gauge hardly moves and heat into passenger compartment luke warm. Unable to locate thermostat in engine compartment.


The thermostat is where your lower radiator hose meets the engine block. There are three bolts to remove to get to it, if your engine is a V6

Nov 29, 2010 | 1991 Nissan Pickup

2 Answers

No heat


your blower motor resistor needs to be replaced if you only have one speed its a small inexpensive part runs about 15 dollars easy to replace.

Jan 17, 2010 | 2000 Oldsmobile Silhouette

2 Answers

No Heat


Hi, the flaps that direct the air for either hot or cold air works with servos situated against the heater box. The grinding noise was the gears on the inside of the servo stripping. After numerous reset processes (switching the car on and off), the servo was reset to its normal state which is in the cold direction. You will have to replace the servo in order for the heater to work again.

Oct 01, 2009 | 2003 Mitsubishi Galant

1 Answer

2003 Toyota Avalon error code p0128 thermostat location


Follow your upper radiator hose to the motor. It will be clamped to your thermostat housing. Unscrew the 2 or 3 bolts holdng the housing down and your thermostat will be right there. Replace thermo. and gasket then reaffix housing and hose. LET MOTOR COOL DOWN BEFORE CHANGING and hour+!!

Jun 12, 2009 | 2003 Toyota Avalon

1 Answer

Thermostat needs replacing


look at the top radator hoses it gos to the top of the motor and were it hooks up to the motor there should be 2 to 3 bolts pull them and there your thermostat.

May 10, 2009 | 2004 Dodge Stratus

Not finding what you are looking for?
1997 Chevrolet Cavalier Logo

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...