Question about Dodge Ram

1 Answer

1987 318 2wd truck carburator keeps plugging up on back with black charcoil

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

Charcoal cannister is bad and so is purge. Either disconnect and plug system, or buy new cannister.

Posted on Nov 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine hard to start after sitting


Sounds like it could be a carburator issue. Fuel could be leaking out of the fuel bowl or back to the fuel tank. You can tell this if you have the breather off and *before trying to start the engine* operate the accelerator arm on the carburator as you look down into the carburator. If the fuel hasn't leaked back you should see it shoot some fuel into the carburator. Also could be a fuel pump problem where the pump lets the fuel leak back and there isn't fuel there to pump up to start the engine when it's cold. Also the 360 wasn't released until 1971 so it's pretty safe to say it's not a 1967 or not a 360.

Aug 27, 2014 | Dodge Cars & Trucks

1 Answer

Car idles high when parked


open the boot from the air filter and MAP SENSOR a black box with small electric connector on, spay small jet of carburator cleaner on sensor( small resistor/ termistor / platinum filament) to clean the dust or deposit dirt. plug back and test. if not fix = open the boot intake hose to engine and where is accelaration cable or electronic controler and inspect the metal disk (air intake ajustment) for deposits and if close ok, if are black deposits = spray carburator cleaner and use the finger to remuve the edge of gums created = more opening = more RPM on idle.

Jul 29, 2014 | Cars & Trucks

1 Answer

Heavy black smoke from b14 engine what is the possible cause ?


Keep in mind the fuel strategy of the fuel injector is what the call PWM(pulse width modulated) so low fuel pressure can cause rich black smoke.coolant temperature sensor that is reading under temperature can cause black smoke and so can the MAF (mass air flow sensor) use carburator cleaner or brake cleaner and clean MAF outside of the vehicle and see if that helps

Feb 26, 2012 | 1996 Nissan Sentra

1 Answer

1990 jeep yj 4.2 straight 6 carburated will turn over but will not start


First try shooting some starting fluid in intake manifold, and if fires up but still won't keep running, my guess next would be your looking and checking out your fuel pump. You can check that out my removing a line and see if fuel is pumping out of the out put of fuel pump. Because it it carburated its pretty easy to trouble shoot. It's going to be in most cases spark plugs , fuel pump.

May 08, 2011 | 1990 Jeep Wrangler

2 Answers

Hi i have a 2000 bonneville ssei supercharged 3.8 my car keeps choking up when i push on the gas pedel and on the highway on cruise at 80kms keep sputtering and get a black smoke from my exaust and...


i had a 91 gmc car, it was fuel injected &(if it was carburated) ran like the choke was stuck,i changed the thermostate sensor & relay(relay cost more)sounds like your car.the computer was getting information that the car was cold.if you can find a manual for your car check trouble shooting. i dont want to plug a company but HAYNES makes a quality manual.hpe this helps

Apr 09, 2011 | 2000 Pontiac Bonneville

1 Answer

How can you adjust the carburetor on a 1987 GMC safari van V-6


If the carburator has never been rebuilt, or the plugs that were installed at the factory have never been removed, you need to remove those plugs, there is one for each idle mixture screw, at the front of the base plate on the bottom of the carburator, 1 for the TPS adjustment on the driver side front of the carburator, and one for the mixture control solenoid on top of the carburator, in the middle, towards the front.

May 22, 2010 | 1987 GMC Safari

1 Answer

1987 dodge ram 50 sport bogging at 55mph


The carburator needs to be retuned under a load to correct the problem. Take the truck back to the place were the carburator was worked on, and have them to check the carburator out for correct adjustments. Hope this will help you !!

May 11, 2010 | 1987 Dodge Ram 50

1 Answer

1987 318 2wd pickup carburator keeps plugging up on back side with black charcoil


anything that looks like chacoal is ussualy a sign of the engine burning oil

Nov 14, 2009 | Dodge Ram Cars & Trucks

3 Answers

Carburator vacuum lines


well i had my motor changed and got it back in but now cant remember where all the plugs and vaccums go ! is there something i can go to show me?

Sep 22, 2009 | Cars & Trucks

1 Answer

Misfires, runs rough, black smoke-90 blazer


if it's carburated, make sure your butterflies are opening.

Apr 27, 2017 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...