Question about Chevrolet Chevette

1 Answer

Id trans. borg warner basic-2 casting #13-52-065-908 also basic-1b what was this installed in?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Mostly came in s-10 or simular vehicle.Not vey heavy duty.I just bought one thinking I got a good deal,but as it turns out this is not a real desirable transmission.

Posted on Mar 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a borg warner 4sd trans it is locked up there is no shifter on it but cant move the lingage i tried a hammer no luck thanks paul


Based on your limited info, I will surmise that this transmission is not mounted and has been sitting around- I will also surmise that you are either talking about the super T-10 or 2nd gen. superT-10 4-speed manual tranny.
Predicated that the aforementioned is accurate, I will guess that the gear oil over time leaked out and the synchronizers, gears, main-shaft, or other internal part(s) have seized up.
You need to open it up and see what is or is not happening internally- but please, do not use a hammer or any other device to hit the transmission levers or transmission body- you'll crack the casting.

Feb 12, 2017 | Cars & Trucks

1 Answer

Resistance specs on borg warner E 262 coil packs


I don't know if this is feasible, but connect two in series for 12 kilohms?

Feb 11, 2015 | Ford Cars & Trucks

1 Answer

How can I install an AMC 360 engine into my 1965 rambler classic with a 287 engine?


what I did was removed the 287 engine installed an AMC 360 .In order to do this you have to get an borg warner m11 bell housing from 67 to 71 .amc used borg warner transmissions until than. So you put the m11 bell housing on to the m8 transmission and get the motor mount for the AMC 360 engine

Feb 10, 2015 | AMC Cars & Trucks

1 Answer

I would like to know if I can install an borg warner m8 tail section onto an borg warner m12 transmission that way I would not have to change from the torque tube subsention


I just found out that all that you have to do is . You have three options to go with one change the bellhousing from a borg warner m12 transmission. two use and borg warner m12 transmission but use the yoke head from the m8 onto the yoke of the m12 yoke .Three use a chryler/amc tf727 torque command transmission.Use the yoke from the m8 weld the head on to the spline of the 727transmission weld the m8 tail section onto eather transmission and that way you can keep the torque tube suspension on your classic 770 with the 287.Your rear end should be an AMC 20 to stand the torque from the AMC 360 engine with about 350 hp .last but at lease get the trany mounts.

Feb 10, 2015 | AMC Cars & Trucks

1 Answer

Id trans. borg warner basic 2 casting #13-52-063-914


ok what are you looking for on the tranny if you need the numbers there is a plate on the tranny or numbers stamped on it

Jan 24, 2013 | Chevrolet Chevette Cars & Trucks

1 Answer

No clutch pressure on a hydraulic clutch system borg warner transmission 4 cyl. 5 speed


look for leak....under the dash on the floor if its wet there its the master. Just follow rod from clutch peddle to master. Check the line and not sure if your slave is on the outside of the trans look there or if its in the trans see if its wet coming out of the bell housing (where trans meets engine) and replace that part and bleed system

Mar 01, 2011 | 1995 Isuzu Rodeo

1 Answer

Im wondering what different transfer cases came in the 91 4x4 f250? mine has borg warner stamped on it


There were 2 Borg Warner Transfer cases in you years truck. A13-56, and a 1345; both are Borg Warner cases.

Sep 01, 2010 | 1991 Ford F250

1 Answer

How to get 99 blazer out of 4 wdlo to 2 wdr hi when push button wont work.


This has a Borg Warner 1350 series transfur cast. cLimb under the truck with a 10 mm socket and rachet and remove the 3 bolts holding the electric transfur case motor, Looks like a soda can. Once removed ,you will see what looks like a try-angle shaft turn it twards the right. You have just moved the low-high fork. Put the motor back on and pull the 4x4 fuse until you change the 4x4 motor

Jun 19, 2010 | 1999 Chevrolet Blazer

2 Answers

Isuzu rodeo manual trans id


cheap truck 4cyl borg warner 6cyl mua

Jan 15, 2010 | 1991 Isuzu Rodeo

2 Answers

What model of transmission does a 1995 Jeep Cherokee with a 4.0 L engine have?


Most common automatic is an AW4...its pretty much based on the old Borg Warner unit (If I remember correctly AW is asian warner or something close to that.)
If it's stick, It could be one of a few but can be ID'd by the vin# or the tag on the unit itself.

Aug 04, 2009 | 1995 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...