Question about 2006 Triumph Tr 7

1 Answer

Fitting new shells inside engine 2600 cc . engine is in a triump 2000 mk 2 1971..

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Triumph Master
  • 22,326 Answers

I asume you done it by now ,nice motors these when new though well sought after as they went like the proverbial clappers

Posted on Oct 03, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Daewoo nubira 2000 oil light coming on and making a lot of noise no heating problem though

Dont start the engine ,jack the car up and drop the sump ,more difficult on this model than the astra of the same year ,what you have is clogged gauze filter on the pick up pipe .You will find also that you will have to fit new big end shells .This problem is caused by not changing the oil every 6000 miles and you get a build up of clag inside the engine ,with a oil change then the oil will clean the build up inside the engine and it congeals on the filter of the oil pump blocking it up .This problem i get a lot of with this model and its got to the point that if i get one in i will not now hold responsability if it leaves me and then does this self same thing .But what i do now is to drain some of the oil out then add a litre or so of diesel and run engine on idle for half hour to try to clean it out before i change the oil .You must change the oil regular

Apr 14, 2013 | Cars & Trucks

1 Answer

Hi can anyone point me in the right direction to find where the oil pressure switch is fitted on the Mk 5 golf Gti 2.litre petrol as would like to change the switch cos oil light intermittently comes on...

Hi Binny, The oil pressure sender unit should be close to the oi filter housing. If memory serves if should be in front of the engine (with you looking into the engine compartment from the front of the car. Regards John

Mar 28, 2012 | 2007 Volkswagen New Gti

1 Answer

Where can i find the engine number embossed on the engine block of Mazda MPV 2000 model?\r\n

mazda mpv 2000 model
tell me the cc of the mpv is it 2000 cc or 2500 cc

Oct 24, 2010 | 2000 Mazda MPV

1 Answer


you should not need a diagram. most gasket kits have the correct torque and order of torque for your fitting procedures. if unsure, put everything of in a line, then reverse to put it on . cheers goodluck

Jun 28, 2010 | 1992 Ford Escort 4 Door

1 Answer

How easy is it to fit big end shells on a 99 gti turbo ( the sump has already been off for a new oil pump

it is possibly cheapest/easier to get a recon short motor(no crank regrind,in shop for days......

Feb 23, 2010 | 2000 Volkswagen Golf

2 Answers

My 2000 Tacoma 6 Cylinder engine warning light came on? Had oil changed yeasterday. All fluid levels are fine. What is happening? Safe to drive? Bjorn

I have a 2000 Tacoma Extra Cab Pre Runner. When I put on my camper shell my check engine light comes on. Oil levels and tires are fine. I took my shell off and light goes off. I hauled alot of wood and the light did not come on. Why would the camper shell be trip-en my light? Ofcourse I am gunna get the code checked next week.

Nov 12, 2009 | 2000 Toyota Tacoma PreRunner

1 Answer

I have bought an engine for my fiat punto 53 plate punto from a salvage yard. I was told the engine was from a punto same year as mine. will this engine fit or is there different models?

hi, the engine you have brought should fit as most of them will fit even if the cc is different so i wouldnt worry to much about it.

The only thing you would have a problem with is if your engine is petrol and they send you a diesel engine.

As long as its the same fuel it wont matter to much if its a bigger cc engine then it will have more power and less if the engine was smaller but they will all fit into your car so i wouldnt worry to much. Even if the engine was out of a car 2 years older than yours or 2 or 3 years newer as they are all the same.

Just make sure you get some sort of warranty because you are buying from a scrap yard they havnt been driving the car around its just come into the scrap yard and they take it that the engine is fine so once fitted check for any noises or oil leaks etc.

You will also need to put your gearbox off your engine onto the new engine as the new one is from a scrap yard it might have the clutch and pressure plate still attatched to teh new engine as this is not a part inside the gearbox but attatched to the engine so if your car had no problems with the clutch then make sure you change this over from your engine onto the new engine.

Also make sure you give the new engine a full service change oil and filter etc.

Also worth doing is once the car is running buy a fuel cleaner that you put into the fuel tank this will then run through the fuel system cleaning all the injectors as the chances are the car has been sitting for a while and may have got bunged up slightly.
Make sure you buy the correct fuel cleaner that goes into the tank ie petrol or diesel ok.

Let me know if you need further assistance ok.

Aug 17, 2009 | 2006 Fiat 124

1 Answer

Knocking noise coming from air intake section on top of engine

The top section of the engine is called a '**** shell' there are baffles inside tha break away and knock. If you press down on this plastic section and the knock goes away. then you have to replace it. It unbolts usinh\g 10mm socket. You need a short one and a long one. also remove the IAC solenoid above the throttle body. **** shell is a dealer item only. also replace the gasket seal.
If the **** shell does'nt come, out gently use a pry bar between the throttle body and the cowl area, for more clearance.

Feb 21, 2009 | 2000 Ford Windstar

1 Answer

Mk 4 vw golf drivers seat large spring fallen out from under seat

You do not need the spring. It was only for keeping the seat back from rattling.

Nov 15, 2008 | 2000 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

500 Answers


Level 3 Expert

80339 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides