Question about 1998 Toyota Corolla

1 Answer

I need help locating the top starter motor mount bolt. I have the bottom one removed and have all electrical disconnected, but I am stumped to find the top 64 mm bolt

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,056 Answers

Try to feel it with your fingers. It should be close to the starter itself. Unless somebody who have worked on that car before broke the head of the bolt.

Posted on Nov 14, 2009

Testimonial: "Thanks, It is behind the air intake manifold @ 5 oclock. 250 mm extension 14 mm socket, pulled out and went back in with ease. Torqued to 39N-m. "

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of "starter" for 1999 cadillac catera


Hi, if you have the 3.0 liter engine, see instructions below. If you have the 4.6 liter, the starter is under the intake manifold.

Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Starter electrical connectors Right hand catalytic converter Right side engine mount nuts Intake air resonator to the throttle body ducts
  3. Install an Engine Support Fixture to the right side of the engine.
  4. Raise the right side of the engine approximately 1.5 inches (38mm) to gain access to the starter motor bolts.
  5. Remove or disconnect the following:

    Engine mount from the bracket and cradle Engine mount bracket bolts and reposition the bracket Starter motor


  6. jturcotte_2359.gif

    Fig. Remove the starter motor and bolts


To install:
  1. Install or connect the following:

    Starter motor. Torque the bolts to 44 ft. lbs. (60 Nm). Engine mount to the bracket and front crossmember. Torque the bolts to 30 ft. lbs. (40 Nm).
  2. Lower the engine into position and make certain that the mount locator tab is fully seated in the front crossmember slot.
  3. Remove the special tools from the engine.
  4. Install or connect the following:

    Engine mount nuts. Torque the upper nut to 30 ft. lbs. (40 Nm) and the lower nut to 41 ft. lbs. (55 Nm). Intake air resonator to the throttle body ducts Catalytic converter. Torque the bolt to 25 ft. lbs. (34 Nm) and the nuts to 18 ft. lbs. (25 Nm). Starter electrical connectors. Torque the battery cable nut to 115 inch lbs. (13 Nm) and the starter solenoid nut to 35 inch lbs. (4 Nm). Negative battery cable

Oct 03, 2011 | Cars & Trucks

1 Answer

Need specifics on Starter motor replacement/ how to.



REMOVAL & INSTALLATION



0900c15280037ceb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Remove the starter electrical connections, noting their locations


0900c15280037cec.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Location of the two starter retaining bolts

  1. Disconnect the negative battery cable.
  2. Detach the air-flow sensor assembly connector and remove the breather hose.
  3. Remove the resonator retaining nuts and remove the air intake hose and resonator assembly as required.


NOTE Use care when removing the air cleaner cover because the air-flow sensor is attached and is a sensitive component.
  1. If equipped with Active-ECS suspension, remove the air compressor as follows:

  1. Detach the two electrical connectors, from the compressor.
  2. Disconnect the air line at the compressor.
  3. Remove the three mounting bolts, securing the compressor to the chassis.

  1. Raise the vehicle and support safely.
  2. Remove the engine undercover.
  3. Remove the heat shield from beneath the intake manifold on the 1.5L engine.
  4. If necessary, detach the speedometer cable connector at the transaxle end.
  5. Detach the starter motor electrical connections.
  6. Remove the starter motor mounting bolts and remove the starter.
  7. The installation is the reverse of the removal procedure. Tighten the starter mounting bolts to 22 ft. lbs. (31 Nm).
  8. Connect the negative battery cable and check the starter for proper operation.

May 06, 2011 | 2000 Mitsubishi Diamante

1 Answer

How to remove a starter on a 86 jaguar xj6 vanden plas starter does not function


The starter motor is located on the passenger side ( left ) side of the motor. it is held onto the motor with two bolts. Before starting the removal process you must disconnect the battery by removing the ground lead. Under the car disconnect the battery feed wires on the solonoid mounted on the starter. Also disconnect the white with red tracer wire on the solonoid. This is the wire that comes from the starter relay on the firewall. Remove the upper bolt first. You can get at it from the top of the engine bay and then remove the bottom bolt. This starter is heavy. The starters on the later cars were a lot lighter. The starter will clear the engine. Be sure to test the new starter before you install it. Installation is reverse of the removal.

Nov 22, 2010 | 1986 Jaguar XJ6

2 Answers

How to remove starter


Removal & Installation - Starter
  1. Before servicing the vehicle.
  2. Remove or disconnect the following:
    Negative battery cable Radiator air baffle assembly
    Electrical connections Torque converter cover Starter
To install:
  1. Install or connect the following:
    Starter. Torque the bolts to 35 ft. lbs. (47 Nm). Torque converter cover Solenoid -BAT- terminal. Torque the nut to 89 inch lbs. (10 Nm). Solenoid -S- terminal. Torque the nut to 27 inch lbs. (3 Nm). Radiator air baffle assembly Negative battery cable
  2. Perform a charging system test and verify the starter is operating properly
8e0154d.jpg

Fig. Showing the starter motor location and electrical connections
  1. Before servicing the vehicle.
  2. Remove or disconnect the following:
    Negative battery cable Radiator air baffle, for clearance if necessary Flywheel inspection cover bolts Flywheel inspection cover Electrical connections from the starter motor Starter motor mounting bolts Starter motor
To install:
  1. Install or connect the following:
    NOTE Before installing the starter motor to the engine, tighten the nut next to the cap on the solenoid BAT terminal. If this terminal is not tight in the solenoid cap, the cap may be damaged during installation of electrical connections and cause the starter motor to fail later.

    Starter motor Starter motor mounting bolts and tighten the bolts to 30 ft. lbs. (40 Nm) Electrical connection to the battery terminal on the solenoid and tighten the battery terminal nut to 13 ft. lbs. (17 Nm) Electrical connections to the S terminal on the solenoid and tighten solenoid S terminal nut to 27 inch lbs. (3 Nm) Flywheel inspection cover Flywheel inspection cover bolts Radiator air baffle, if removed
  2. Connect the negative battery cable

Hope helps, remember rated this.

Aug 12, 2010 | 2001 Pontiac Montana

1 Answer

How to change the starter in a 1998 Mazda 626


1993-98 626/MX-6/Probe Models

2.0L ENGINE

(see Figures 5, 6, 7, 8, 9 and 10)
  1. Disconnect the negative battery cable.
  2. Remove the fresh air duct and resonance chamber.
91a666b.jpg

Fig. 5: To remove the starter motor, first remove any obstructing components, then loosen the upper starter motor attaching bolts

78fd60e.jpg

Fig. 6: Remove both upper bolts before going under the vehicle to finish the removal procedure
  1. Label and disconnect the electrical connectors and remove the air cleaner assembly.
  2. Remove the intake manifold bracket.
1536d13.jpg

Fig. 7: Raise and safely support the front of the vehicle, then label and detach any plug-on wire connectors

59b31de.jpg

Fig. 8: Using the proper size socket or wrench, remove the battery positive wire retaining nut ...

9934705.jpg

Fig. 9: ...and the wire terminal from the starter
  1. Label and disconnect the wiring at the starter.
  2. Remove the starter mounting bolts and remove the starter.
a62a8db.jpg

Fig. 10: Remove the lower starter motor mounting bolt and carefully lower the starter and remove it from the vehicle
  1. Installation is the reverse of the removal procedure. Tighten the starter mounting bolts to 33 ft. lbs. (3 Nm) and the intake manifold bracket bolts to 38 ft. lbs. (8 Nm).

2.5L ENGINE
  1. Disconnect the negative battery cable.
  2. Remove the fresh air duct. Disconnect the electrical connector and remove the air cleaner assembly.
  3. If equipped with automatic transaxle, proceed as follows:
    1. Relieve the fuel system pressure. Drain the cooling system.
    2. Disconnect the accelerator cable from the throttle body. Label and disconnect the electrical connectors, vacuum hoses and coolant hoses from the throttle body.
    3. Remove the throttle body.
    4. Disconnect and plug the fuel supply and return lines.
    5. Disconnect the transaxle selector cable from the transaxle and remove the cable bracket.
    6. Remove the starter bracket.
  4. Label and disconnect the wiring at the starter.
  5. Remove the starter mounting bolts and remove the starter.
  6. Installation is the reverse of the removal procedure. Tighten the starter mounting bolts to 38 ft. lbs. (8 Nm).

Hope this help (remember comment and rated this help). TY for using Fixya.

May 12, 2010 | 1998 Mazda 626

1 Answer

I need a diagram to find my aluternator in my 1998 dodge strstus please.


2.0L DOHC Engine
See Figure 4
  1. Disconnect the negative battery cable.
  2. Disconnect the starter motor electrical connections.
  3. Remove the starter motor mounting bolts and remove the starter.


cb88b61.jpg Fig. Fig. 4: Exploded view of the starter motor mounting-2.0L engine
To install:
  1. Clean both surfaces of the starter motor flange and the rear plate. This is important since the starter grounds through its case and the transaxle flange to which it attached. Some remanufactured starters may have paint on these areas which should be cleaned off before installation. Install the starter motor onto the transaxle and secure with the retaining bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  2. Attach the electrical harness connectors to the starter.
  3. Connect the negative battery cable and check the starter for proper operation.

2.0L SOHC Engine With Manual Transaxle
See Figures 4 and 5
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with a insulator grommet which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Remove the air cleaner resonator.
  3. Remove the positive battery cable retaining nut from the starter.
  4. Disconnect the positive battery cable and alternator output wire from the starter.
  5. Disconnect the push-on solenoid connector from the starter.
  6. Remove the 2 bolts that attach the starter to the transaxle.
  7. Remove the starter from the vehicle.

14f147d.gif

Fig. Fig. 5: Starter motor wiring terminal connections-2.0L engine To install:
  1. Install the starter and the attaching bolts to the transaxle assembly.
  2. Tighten the attaching bolts to 40 ft. lbs. (54 Nm).

Clean all dirt and/or corrosion from the wire terminals before reconnecting the wiring to the solenoid.
  1. Reconnect the push-on solenoid connector to the starter.
  2. Reconnect the alternator output wire and positive battery cable to the starter and tighten the retaining nut to 90 inch lbs. (10 Nm).
  3. Install the air cleaner resonator.
  4. Reconnect the negative battery cable.

2.0L SOHC Engine With Automatic Transaxle; 2.4L Engine
See Figures 4, 5 and 6
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with a insulator grommet which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Remove the air cleaner resonator.
  3. Remove the 3 bolts attaching the Transmission Control Module (TCM). Do not disconnect the TCM wiring. Move the TCM to gain access to the upper starter mounting bolt.
  4. Remove the upper starter mounting bolt.
  5. Raise and safely support the vehicle.
  6. Remove the positive battery cable nut and disconnect the cable from the starter.
  7. Disconnect the push-on solenoid connector.
  8. Remove the lower mounting bolt that attaches the starter to the transaxle.
  9. Remove the starter from the vehicle.


2f4680e.jpg

Fig. Fig. 6: Starter motor wiring terminal connections-2.0L SOHC engine with A/T; 2.4L engine To install:
  1. Install the starter onto the transaxle and the lower mounting bolt.
  2. Tighten the mounting bolts to 40 ft. lbs. (54 Nm).
Before reconnecting the wiring to the starter solenoid, be sure to clean the wiring of any dirt or corrosion.
  1. Reconnect the positive battery cable to the solenoid post and tighten the retaining nut to 90 inch lbs. (10 Nm).
  2. Reconnect the push-on solenoid connector.
  3. Lower the vehicle.
  4. Reinstall the upper attaching bolt and torque to 40 ft. lbs. (54 Nm).
  5. Reinstall the TCM to its original location and install the mounting screws.
  6. Reinstall the air cleaner resonator.
  7. Reconnect the negative battery cable

Hope helped.

Feb 01, 2010 | 1998 Dodge Stratus

1 Answer

Howm do I replace a starter on a 1995 Nissan


Nissan 240SX/Altima 1993-1998 Repair Guide

Altima
(see Figures 1, 2 and 3)


ef972ea.jpg
Fig. 1: The starter is located to the left of the oil filter housing on the engine block


dfca7b3.jpg
Fig. 2: The starter motor is removed from the bottom side of the engine compartment


04c206e.jpg
Fig. 3: When installing, be sure to align the starter's mounting bolt holes with those in the engine block
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the starter support bracket, as required.
  4. Label and disconnect the starter electrical harness.
  5. Support the starter from beneath the vehicle using a jackstand.
  6. Remove the starter mounting bolts.
  7. Carefully lower the starter from the vehicle.
To install:
  1. Position the starter on the engine and support it using a jackstand.
  2. Install the starter mounting bolts and tighten to 30-37 ft. lbs. (40-50 Nm).
  3. Connect the starter electrical harness.
  4. Install the starter support bracket, as required.
  5. Lower the vehicle.
  6. Connect the negative battery cable.

Hope helped with this (remember rated this help) Good luck.

Nov 27, 2009 | 1995 Nissan Altima

1 Answer

2004 jeep liberty replacing the starter


2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Oct 04, 2009 | 2004 Jeep Liberty

1 Answer

BMW 328i Starter how to replaice


1999 BMW 328I 2.8L EFI DOHC 6cyl

Starter - Removal & Installation

The starter motor on some models is very difficult to see from the top of engine compartment as it is covered by the intake manifold. On these models, without removing the intake manifold, the starter motor must be removed from underneath the vehicle. Because the starter motor mounting bolts are not easy to access, a long extension with a universal joint mounted on a proper sized socket could be used. A three foot transmission extension is commercially available from tool vendors that has a 3 / 8 inch drive of the driven end and 1 / 2 inch drive on the drive end. If used with a non-binding impact universal joint and a proper fitting impact socket, the starter motor fasteners can be removed from underneath the vehicle.
Once the starter motor fasteners are removed, the starter motor may have to be moved side-to-side several times to loosen the dowel pin if it has corroded in place.

NOTE When the battery is disconnected, the radio code, on-board computer and clock settings will be lost. The radio code should be obtained before disconnecting the battery or radio. Once the battery has been reconnected, the radio will not function unless the code is keyed in.
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm) Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) E36 6-Cylinder Engines
Automatic Transmission Models
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Remove the climate control air intake duct at the rear of the engine compartment as follows:
    1. Release the grille clips at the rear and lift the grille upward from the rubber seal, then remove the seal.
    2. Remove the two self tapping Phillips screws from inside the duct to release the electrical harness housing.
    3. Press the electrical housing downward to expose and remove the two hex head self tapping screws on each side of the duct and lift the duct up and out of the engine compartment.
  5. Remove the intake manifold trim and valve cover trim covers.
  6. Disconnect the ignition coil electrical connectors and ground straps, label for reinstallation and place aside.
  7. Remove the two fasteners that secure the fuel injection electrical connector harness to the rail. Remove the harness and carefully place aside toward the back of the engine compartment behind the right side strut tower.
  8. Remove the intake manifold.
  9. Remove the electrical leads from the starter motor and place aside.
  10. Remove the starter motor mounting fasteners at the transmission bell housing, then remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket, then lift the starter motor upward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.
Manual Transmission Models
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Raise and safely support the vehicle.
  5. Remove the fasteners for the reinforcement mounted between the frame rails just behind the rear lower control arm bushing brackets. Mark the bar-s direction for proper reinstallation and remove the bar.
  6. Remove the fuel line cover located near the left side rear lower control arm bushing bracket.
  7. Release the fuel lines and reverse light wiring from their routing brackets.
  8. Note the routing of the starter motor electrical wires, remove the wire mounting nuts, and place the wires aside.
  9. Remove the top and bottom starter motor to engine-transmission mounting fasteners.
  10. Remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket and carefully lower the starter motor downward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.

Fig. A view of the starter motor mounting fasteners and dowel pin. The mounting bolts are threaded into the starter motor

cd45991.jpg

Fig. The starter motor mounting bolts are a different size than the transmission-to-engine mounting bolts

2cbfa11.jpg

I hope help you with this (rated this help) Good luck.

Sep 22, 2009 | 1999 BMW 328 Series

1 Answer

Starter replacement


  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If necessary for access, remove the splash shield.
  4. If equipped, unfasten the flywheel inspection cover bolts and remove the cover.
  5. Label and detach the electrical connectors from the starter.
89632p02.gif Unfasten the starter motor electrical connections. You may want to tag them first to avoid confusion
89632g34.gif Exploded view of the starter motor electrical connections
Click to Enlarge
  1. It may allow more room it you remove the right side cooling fan.
  2. Remove the starter-to-engine bolts, then carefully lower the starter from the vehicle.
89632p03.gif The starter is attached to the engine with 2 mounting bolts (see arrows)
89632p04.gif Unfasten the front mounting bolt (1) and remove any necessary shims (2), noting their locations for installation
Click to Enlarge
89632p05.gif Unfasten the long starter mounting bolt, then remove the starter motor from the vehicle
Before installing the starter motor, make sure the electrical terminals are secure by tightening the nuts next to the cap on the solenoid battery terminal and on the "S" terminal. If these terminals are not tight in the solenoid cap, the cap may be damaged during installation of the electrical connections and cause premature starter failure.
89632g33.gif

Oct 22, 2008 | 1994 Buick LeSabre

Not finding what you are looking for?
1998 Toyota Corolla Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...