Question about 2003 Chevrolet Suburban 1500

1 Answer

Just replaced front wheel bearing hubs assy. What is the torque spec for the nut? 1500 series Z71 4x4.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,036 Answers

THE HUB AND BEARING ASSEMBLY MOUNTAINING BOLTS TORQUE IS 133 FT LBS.

Posted on Nov 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front right wheel bearing


This is a hub and bearing assy. You will need to remove the axle nut, brake rotor, caliper assy. There are 3 or 4 bolts that attach the hub assy to the knuckle assy. Most of the time, the hub assy will come out easy and sometime it comes out very hard. Make sure you torque the axle nut to the proper spec, so the bering will not fall apart and will last. Buy a quality hub and bearing assy, so you dont have to do it again.

Nov 03, 2013 | 1995 Oldsmobile Aurora

1 Answer

How to assemble a front wheel bearing on a 2003 GMC Sierra 1500 4x4


The front wheel bearing is a hub and bearing assembly. To remove you will.... 1. Remove the tire 2. Remove the axle nut. You can put a punch in the fins of the rotor to keep the assembly from turning while you rmove the nut. You can can do the same thing when you torque the axle nut. 3. Remove the caliper and rotor. 4. Unplug the abs sensor if equipped. 5. Remove the three bolts that hold the hub to the knuckle. 6. Rmove the hub. If you need torque specs let me know and i'll get them for you. It is absolutely critical that you torque the axle nut to the proper spec!

Oct 08, 2011 | Cars & Trucks

1 Answer

Torque specs 98 riv replacing wheel hub assy


Hello blboyer0,

The torque for the axle nut is 107 ft. lbs. The hub bearing bolt should be torqued to 70 ft. lbs.

I hope this helps.

Regards,

netvan

Aug 07, 2011 | 1998 Buick Riviera

1 Answer

How do i change the driver side front hub assembly


The vehicle will need to raised on the left (drivers) side and supported. Remove the tire, then the brake caliper assy. Remove the rotor, then remove the axle nut located in the center of the hub assy. Remove the hub/bearing retaining bolts, and then the hub assy. Some times it is corroded into the steering knuckle assy. and will not seem to come out. If this happens, install the axle nut, and wearing safety glasses, pound onto the hub flange from the inside to the outside, until it comes out of the knuckle assy. Then remove the hub assy. Clean the knuckle hole where the bearing with 120 grit sand paper, so the hub/bearing assy will go into the knuckle without damage. Torque the axle nut to specs. Clean the inside of the rotor, where the hub meets it, so it sits flat against the new hub. Install the rotor, caliper assy. Install the wheel and torque the lug nuts to 100 ft pounds. Road test about 5 miles and recheck the lug nuts.

Jan 19, 2010 | 1998 Ford Explorer

1 Answer

I think my front Drivers side wheel bearing is going out on my 2004 dodge ram 1500 4x4. It is an ABS system. What should I do to replace this? I wouldnt mind doing it myself if its the cheaper route.


Remove the wheel, the brake caliper with the mounting bracket and pads all together, the brake rotor, and the axle nut. Make sure the axle is free inside the hub splines by pushing it in a bit. I believe this truck has 3 bolts for the hub/bearing assy. They remove from the inboard side of the knuckle, then the hub/bearing assy comes out. It may be corroded in the knuckle, so some force may be required to get it out. To reassemble, reverse the steps, being careful to torque the axle nut to the proper spec. Also pump the brake pedal before you road test to verify the noise is gone.

Jun 27, 2009 | 2004 Dodge Ram 1500

2 Answers

Torque specs


the center bolt for cv axle!103ft-lbs,hub bearing assembly bolts!77ft-lbs

Apr 26, 2009 | Chevrolet Blazer Cars & Trucks

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
2003 Chevrolet Suburban 1500 Logo

742 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...