Question about 1995 Nissan Pickup

1 Answer

I am having to push my clutch completely to floor to get the clutch to engage. I have about 1 inch of play. What should I check first. 95 Nissan PU King

Posted by on

  • doctordatsun May 11, 2010

    do you mean DISengage? This is a self adjusting clutch. Check for signs of leaking around master and slave cylinder- it may be time to replace one of them.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,418 Answers

Under the hood you will find the clutch fluid reservoir check that for low fluid. It's possible you have a minor leak on the slave cylinder.

Posted on Nov 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car has difficulty going in gear even if pedel is fully down


The clutch is not fully disengaging. Adjust the clutch cable to obtain a 1/2 inch of free play at the top of pedal stroke. If clutch adjustment is not correct, damage to synchronizers or clutch release bearing will occur. Your clutch should begin to engage about an inch off the floor when releasing the clutch pedal.

May 25, 2017 | Cars & Trucks

1 Answer

How to adjust 95 geo tracker clutch


engaging?
you meant dis-engage im sure.
pedal up is engaged,
pedal at floor dis-engages it.
my guess, is the clutch drags unless i push the clutch pedal 100%
to the floor.
1: bad cable is 90% cause. non last this long.
2: no free play is way too loose.
3: broken lever on the pedal top. caused by #1

all fail modes covered here.
http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

Apr 23, 2014 | Geo Tracker Cars & Trucks

1 Answer

Clutch pedal travel


Your pedal height may be adjustable by a stopper bolt at top of pedal. You would have to check the specification for your car. Most important that the pedal has about a half inch free travel before clutch begins to engage. You need that free play to ensure the release bearing (the throw-out bearing) is not touching the fingers on the pressure plate when not engaged. If it always is touching, it will be rolling around constantly and will go out prematurely.
Your new clutch will allow gear engagement sooner as the clutch pedal is released. I mean gears will engage just as pedal is lifting off from floor. You should notice that difference-the old clutch would have taken longer pedal travel from floor before releasing.

Apr 15, 2013 | Cars & Trucks

1 Answer

Clutch pedal has about 1/2 inch of play before engaging, from the floor. How can I adjust this?


there is a very small amount of adjustment on the rod which pushes in the master cylinder piston. what you are talking about however, the engagement point, is that your clutch pressure plate and disc need to be replaced. they are worn out and not releasing until maximum movement of the slave cylinder. this will not be cheap.

Jun 10, 2011 | 2004 Saturn ION

1 Answer

1985 jeep cherokee how far from the floor does the clutch engage?


In just about all vehicles you should have about 1/2 to 3/4 inch free-play before clutch begins to release. Adjustment is done this way , Not from the floor up...

Sep 16, 2010 | 1985 Jeep Cherokee

1 Answer

Clutch stays down, has about half an inch of play below carpet level, still able to shift but have to use toe of shoe to pull pedal up. happens two or 3x a day


you have 4 cyl or V6 engine, how much free play you have on clutch pedal (take your hand press clutch in untill gets harder to push in) should only have about 1" free play, and also when you release clutch while in gear should start engaging about 1 1/2" up when releasing

Feb 04, 2010 | 1993 Toyota Pickup

1 Answer

Put in gear clutch feels good does not move like it's suppose 2 it's a stickshift


How is it suppose to ? What is 2 ?Does the clutch engages right away when you release the pedal or almost at the end (pedal up), did you check the freeplay on the pedal ? Should have free play, push clutch pedal by hand and you should move it a half inch before feeling resistance.

Aug 11, 2009 | 2004 Nissan Maxima

1 Answer

1997 hyandai accent gt clutch problem


hi considering age of car and that you have no leaks on hydraulics? may i suggest you try bleeding the clutch to rid of old fluid a couple of pumps may be suffice ? b/fluid does absorb moisture and heat over time hence recommendation tat fluid be changed at period specified in handbooks ie 12 monthly ?

May 15, 2009 | 1994 Hyundai Excel

2 Answers

Location of Turn signal flasher for 95 Nissan 4wd 4cyl MT


Found it!! - It is indeed under the dash, directly above the clutch pedal arm and attached to the brake support bracket. The original one was black and NOT round. It's about 1.5 inches long and 1 inch square. The three wires drop down out of the bottom and there is a connector release you have to push to release the wires. The flasher relay itself can slide off the mounting point, with a little extra pressure, pushing towards the left side (outward) of the truck. (left hand drive models).

Jan 28, 2009 | 1995 Nissan Pickup

2 Answers

2007 Nissan Xterra Offroad Cltch replacment


$2800?!?!?!?!?!!!!!!! HOPE THAT IS A MISPRINT
if it is feeling different then something is not right. the amount of travel should not change
you may have a slave cylinder problem or your clutch release fork has popped off the pivot ball

Sep 22, 2008 | 2006 Nissan Xterra

Not finding what you are looking for?
1995 Nissan Pickup Logo

Related Topics:

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...