Question about 2000 GMC Jimmy

1 Answer

How do I change a flasher on a 2000 GMC Jummy?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 5,081 Answers

There are a row of Allen head and 9/16 nut screws on the bottom panel below the steering wheel and middle panel, remove those.
Gently pull down lower panel, upper panel will pull out as well slightly. The hazardflasher (left) and turn signal (right) are just to the left of the lighter assembly. (Silver)Relays are difficult to pull out, if you gently use wide mouth pliers , rock them out. Replace and test, before reinstalling panel.

Posted on Nov 14, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to fine the signal lights flasher on a 2000 GMC 3500 van


2000 GMC Truck Savana 3/4 ton Van 4.3L FI OHV 6cyl

The Flasheris located: Front seating area, driver side, under dash, below steering column, mounted in relay block

Aug 12, 2017 | GMC Cars & Trucks

1 Answer

Gmc jimmy stuck 4wd

4x4 actuator faulty or stuck

Dec 17, 2013 | Cars & Trucks

1 Answer

2000 GMC Jimmy, Sigal flasher clicks away when no in the on position,signals seem to work ok when requested,when stepping on brake it seems to get more rapid at i need a new flasher?

try taking out the flasher relay and putting dioelctric grease on connections this may help it will not solve problem completely. I have the same issue

Feb 16, 2013 | 2000 GMC Jimmy

1 Answer

Gmc jummy electirc proble about fule come but injucter is not working

with the key on you should have power on one wire at each of the injectors and the ground circuit is controlled by the computer.with a voltmeter you see battery voltage on one wire and you see the ground voltage can see this best on a meter that has a graphing meter on it.

Oct 31, 2011 | 1998 GMC Jimmy

1 Answer

I have a 2000 jimmy full load vehicle the flasher keeps ticking after it is turned off everything works as it should but it just keeps ticking

This is common problem. The problem is caused by a bad function switch in the dash, It shorts and coauses flasher to click from time to time. The only fix is to change the switch assembly on column and your clicking will stop. good luck

Oct 15, 2009 | 2000 GMC Jimmy

1 Answer

Flasher clicks all the time. I have replaced the flasher, but still hear this clicking from the flasher. This is a 2000 GMC Jimmy.

there is a short in the switch in the steering coumn. unfortunately this assembly is very expensive. your problem is quite common you are not alone. you cannot fix it unless you replace the switch assembly

Aug 29, 2009 | 2000 GMC Jimmy

1 Answer

2000 GMC 3500HD Warning Flashers will not work

yes it is in the turn signal switch assembly. I see that Carquest has them and probably sure NAPA will as well.

Jul 30, 2009 | 2000 GMC Jimmy

Not finding what you are looking for?
2000 GMC Jimmy Logo

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides