Question about 2005 GMC Yukon

3 Answers

Having problems getting gasoline into my Yukon, after putting only a dollar or so into my truck it kicks back as if it were full, takes forever to get gas, can you help?

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 460 Answers

There is an obstruction in the pipe where you insert the pump nozzle probably someone played a very unkindly prank. im affraid the only recourse is to have it looked at by a mechanic..good luck..

Posted on Nov 14, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 6,826 Answers

There is a vent tube either running beside the filer hose to the tank,or in side the filer hose,and it is blocked,or restricted,somewhere,some how,the dealer might have a bulletin on this model,call them to find out.

Posted on Nov 14, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Sounds like somebody put something in your gas filler tube. Take a flashlight and try to look inside. You probably won't be able to see but I would try that before removing the hose between your gas door and the gas tank. You could try feeling with a coat hanger but you may not want to push whatever it is inside your gas tank.

Posted on Nov 14, 2009

  • ianbhps Nov 14, 2009

    I had a another thought. You may want to check the vent tube that comes off the gas tank as well.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 hyundai accent is using up too much gas need help


city driving is 22-24 mpg depending on whether manual or automatic.

Driving style plays a big part in fuel economy. Anticipate braking, in fact try not to use your brakes. Accelerate like there is an egg under your right foot and you don't want to crack it. Also, it is better to keep the tank full as half a tank has lot of room for evaporation of gasoline.

Fuel Economy of 2001 Hyundai Vehicles

May 13, 2017 | Cars & Trucks

3 Answers

When putting gas in my 2004 Kia amanit the fuel nozzle kicks off. How do I locate and fix the problem


HI Bridgette,

Due to the different shapes of fuel tank filler necks in cars & trucks, it may be necessary to vary one or more things to allow fuel to flow uninterrupted until the tank is really full.

The main problem can come from the new "vapor recovery" gasoline pumps. These pumps and hoses actually recover gasoline fumes from your tank as the liquid gasoline displaces the air / fumes in the tank is it is being filled. If gasoline flow is started at full blast, it can splash back slightly, causing liquid to be pulled back by the pump - so it shuts off. So, start with a slow rate of filling and gradually increase flow rate to maximum over 5 to 10 seconds. If it still shuts off, try some of the suggestions below.

First, don't fill at maximum flow rate from the pump - that is, don't set the nozzle for wide open. Select one of the other "latches" on the handle instead of the fastest flow and let the tank fill entirely at this rate.

Second, you should experiment a bit with the length of nozzle that you push into the tank's filler neck. If you push it in too far or too little, the pump nozzle can do what you're describing.

Third, try twisting the nozzle slightly so that it doesn't hang straight downward - a little to the left or right may provide a solution.

Lastly, try a different gas station. Their pumps may not be so picky with your tank's filler neck.

Good luck!

Jun 14, 2012 | 2004 Kia Amanti

2 Answers

No heat


your blower motor resistor needs to be replaced if you only have one speed its a small inexpensive part runs about 15 dollars easy to replace.

Jan 17, 2010 | 2000 Oldsmobile Silhouette

1 Answer

On my wifes 2004 yukon, the engine warms up and the blower works fine, but it takes forever for the air to finally blow warmly. when it finally does, if we switch it to another location (floor or defrost),...


iwould check the selector motor,and also replace the thermostant,start with the stant first,the selector motor is what runs the door for hot or cold the motor is a common problem,if the temp gauge is showing a quick warm up temp then its the selector motor, if it takes a while to reach operating temp then replace the t-stant,also make sure the coolant is full in radiator,check when cold or warm,dont open when hot, hope this is helpful.

Jan 03, 2010 | 2004 GMC Yukon

1 Answer

2005 Yukon XL smells like gasoline fumes


you need to take dealership have your evaporative emission control system check.also check the fuel pressure regulator for gas leak.most of the time the o - ring will leak.cause gas fume smells

Dec 05, 2009 | 2002 GMC Yukon XL

1 Answer

Starter kick back


If this is a gas engine, check the ignition coil or plug wires. A simple test...

Start the truck at night, then look under the hood while it's running. Don't use a flashlight or your headlights; it should be dark !

If you see sparks anywhere around the engine, you've found the problem. Now you can turn on a light to see where they're coming from - probably from a cracked ignition coil.

Good luck !

Marco

Feb 05, 2009 | 1999 GMC Yukon Denali

1 Answer

Engine light on


If the engine light comes on on the car its the problem with the engine get it checked from the mechanic and look for what code its coming on car you can find the problem and then fix the issue with dealer ......................

Jun 01, 2008 | 2003 GMC Yukon

1 Answer

Check engine light is on


if you buy this car and the check engine ligh come on one hr after you bought it that means the problem was there allready
take it back and have them fix it right,
but if not go to autozone for a free diagnose and tell me what the codes are and we go from there

Jun 01, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
2005 GMC Yukon Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...