Question about 2003 Ford Excursion

1 Answer

Where do i find the iat sensor on the ford v-10

Posted by on

  • yadayada
    yadayada May 11, 2010

    the IAT is part of the MAF sensor.

  • yadayada
    yadayada May 11, 2010




1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Ford Master
  • 76,164 Answers

Sorry gave you wrong info, the IAT is located in the aircleaner box, here is a picture of it.

where do i find the iat sensor on the ford v-10 - a1eabf4.jpg

Posted on Nov 13, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2005 ford taurus with a p0113 code saying high circuit

p0113 means you are getting a very high voltage reading from the IAT sensor to the ECU. Usually this is because the IAT has become faulty or bad. Replace and clear codes it should go away.

Aug 16, 2016 | 2005 Ford Taurus SE

1 Answer

My 2004 fi50 has code po113 i just change the vct sensors

i moved you to F150 (ok/?) 5.4liter or what?
now you can get Ford answers and not Toyota.side show.
did you reset all DTCs after the service? (always 1st step)

VCT (or VVT in generic form)
is tricky.
in fact id never assume the sensor is bad first. (id clean them an believe them)
p0113 is IAT sensor open. (if unplugged key on, bingo)
are you using a scan tool that can see all FORD codes???
id bet not but if are, then there are many VVT codes.

Trouble Code Conditions: verbatum FSM.
Key on or engine running; and the PCM detected the IAT sensor signal was more than the self-test maximum 4.60v (Scan Tool reads under -46F). This is a thermistor-type sensor with a variable resistance that changes when exposed to different temperatures.
Possible Causes:
  • IAT sensor signal circuit is open (inspect wiring & connector)
  • IAT sensor signal circuit is shorted to VREF (5v)
  • IAT sensor is damaged or it has failed

my guess is doing service key on with IAT unplugged.

Jul 03, 2014 | Ford F-150 Cars & Trucks

1 Answer

I need to locate the iat for 2012 Ford Triton V-10 6.8 liter plus wire colors for the two wires that supply the iat

That sounds like a Mass Air Flow sensor. Why are you checking it? What are your symptoms? Make sure your air filter is clean.

Aug 18, 2017 | Cars & Trucks

1 Answer

I have a 2008 Ford fusion and I need to know what wire go to the Iat sensor

Trying to "soup-up" your tiny little 4-banger by by-passing the IAT? My recommendations are DON'T DO IT! You are opening a can of worms that you may not be able to afford in the not-so-distant future.

However, who am I to tell you how to waste your money?

The IAT signal input to the PCM is Pin #1 VIOLET/GREY at the MAF/IAT sensor connector.

Mar 06, 2012 | 2008 Ford Fusion

1 Answer

I need to know where my MAF/IAT sensor wires are on my 2002 V6 ford mustang

it's the sensor on the intake air duct come out of your air filter. the iat sensor is integrated with the maf sensor

Mar 13, 2010 | 2002 Ford Mustang

3 Answers

Where is the iat sensor on a ford escape 2001 v-6

Inside the MAF (Mass Air Flow) sensor.

Nov 06, 2009 | 2008 Ford Escape

1 Answer

I need to locate IAT sensor four my 2009 ford

The IAT is integrated with the MAF sensor on the 09 Fusion. The MAF is located near the air box on all three engines. on the driver's side, and will be held to some part of the intake tubing by 2 torx screws. 2.3L shown, 3.0 and 3.5 should be similar.

Oct 04, 2009 | 2009 Ford Fusion

2 Answers

I cant find the IAT sensor on my 98 ford explorer XLT v 6 SOHC

Try “” or your local library for diagrams and step by step instructions.

Mar 12, 2009 | 1998 Ford Explorer

1 Answer

Possible bad IAT sensor

i doubt it's the IAT in the air cleaner tube. Go to an auto parts store and ask them to scan your car for fault codes & see if one says a bad IAT.
It may be the start of your fuel pump in the fuel tank failing. Need to check pressure to see if maintains 40 psi. Gauge connects to fuel rail shrader valve.

Feb 19, 2009 | 1996 Ford Taurus

1 Answer

I need to located the IAT sensor for a 1999 FORD F-250 disel 7.3

should be in the air intake tube or filter box

Jan 17, 2009 | 1987 Ford Escort

Not finding what you are looking for?
2003 Ford Excursion Logo

Related Topics:

447 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides