Question about 1997 Ford F150 Regular Cab

1 Answer

Leak developed in the back window. I dont know how to take the plastic trim off with out breaking it.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

There are clips that hold it in place most times you have to remove the inner shield then re-glue the otter shield in. go to your local glass shop and ask them how much it would cost. I have done them and they are all different but a lot of times they have short cuts and Can do it faster and cheaper than yo can as they have the tools and they can keep the shop warm enough for it to cure it correctly. sometimes they will just shellac it in place to stop it from leaking, I have replaced all of my own front windshields and they would remove it and replace it for 40 dollars. Believe me I would rather give them the money cause the guarantee it and normally get it done quickly.

Posted on Nov 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove interior rear side panels to remove the speakers on 03 Toyota prerunner ext cab


Make sure that any door rubbers are removed off the plastic trim.
Being very careful, grab a hold of front or back of trim and lift away from panel. These are clipped onto the panels with plastic clips,
Sometimes they break , but most of the time they come away just fine.
Dont pull too hard or the whole trim might snap

Feb 02, 2015 | Toyota Cars & Trucks

1 Answer

How to replace passenger window motor on a 04 Nissan altima


Are you sure it is the motor and not the switch? Motor requires the door trim to come off,careful to remove all screws,all padding and plastic barrier.Then you will have to drill out the rivets holding the motor to the door body.Nuts and bolts are needed to install the new motor.Work carefully and get some plastic trim removers,they are cheap and worth the coin.you are going to probably break the plastic pops that hold the door trim against the door.These are readily available at most parts stores. This is a reasonably simple job if you have the tools.Just double check those window switches first,I've seen more bad switches than window motors.Good Luck

Apr 27, 2014 | Cars & Trucks

1 Answer

How do I remove drivers door trim? I need to fix the door pull handle.


would be held on by plastic clips around the lower sides, and by screws (like under inside door handle) that may be covered by little plastic plates which you pry off to see the screw underneath. The armrests and pull handles also use large screws. Once you get all the screws out, slip a thin bar (thin screwdriver?) under the door trim around the bottom and gently pry outward to unfasten the clips. they break easily, so work carefully, you can also buy new ones at any parts store if you ruin any. they slip[ into slots on the backside of the trim panel. Oh, yes, need first to remove window handle, unless you have power windows, then when panel is loose, reach inside and disconnect the electric switches. Once trim panel is removed, carefully peel back only what you need to of the plastic watershield. when finished you can re-stick the watershield.Simple job, but sometimes a PITA>

Oct 04, 2011 | 1997 Chevrolet Tahoe

1 Answer

Need to replace sunroof..


you need to replace glass or is it leaking if leaking then you have to remove upper seat belt covers pop off remove bolt 14mm and the trims on upper pillars pry off carefully held in by clips remove covers on interior light at front where sunroof switches are there are screws by bulbs disconnect connector remove center light cover and screws disconnect connector with clean hands remove rbber trim around sunroof opening and plastic cover on each side of sunroof glass held on with plastic screw clips then remove four 10mm nuts lift sunroof glass out of car remove cover and screws from rearview mirror all plastic trims around headliner move pass seat forward most and flip back rest all way down roll pass window fully down then slide headliner out of car now you can remove electrical connectors and remove water flow hoses from sunroof unit remove 8 12mm nuts holding frame to roof remove through door you will see the track sunroof slides on remove nuts along problem is silicone between track and frame is deteriorated lift track clean replace silicone reattach frame to roof dont put trims or liner in till test connect switches and glass to frame make sure sunroof works and closes fully then go through car wash to see if leak is fixed

Jan 13, 2011 | 2001 Subaru Legacy

2 Answers

The front driver window made noise going up and then fell down.


It sounds like it came off the track. Take the panel off the door and inspect. Sometimes the rivets they use break, if that is all replace with small bolts.

Jul 16, 2010 | 2000 Jaguar S-Type

3 Answers

Ford 2004 F150, Lariat, crew cab I have a


I had the same problem with my truck,ieven took it to a window repair shop while driving home it started to rain lord a behold,I looked on the back sit and it was wet.After all that i found out that the water was comming in from the break lite on top of the roof.all you have to do is take the cover off and replace the seal around the cover because it is worn out or get some sealeant and place it around the inside cover.

Jan 05, 2010 | 2004 Ford F150

1 Answer

My son broke the power window lock in my 89 toyota landcruiser, I can no longer roll down any windows besides the driver's side. I need to know the best way to take apart the passenger door so I can pull...


I have a 1989 Landcruiser but without power windows so I will tell you what I know about mine.

First remove the arm rest. you will need a large phillips head screw driver for this. Then remove the plastic trim around the door handle. This is only one regular sized phillips screw. Carefull not to do this one up too tight when you put it back on or it will crack.

The door trim is held on by about 10 plastic plugs around the edge that just pop out. Put a large flat blade screw driver behind the trim up close to where each pin and with a little twiste is should pop off. The wood isn't that strong (masonite) so you need to be gentle.

I don't know how the window switch or the door lock works as mine are mechanical but I imagine there would be some spare cable so you can partialy remove the trim and get your arm in to remove the cables.

Once the trim is off the car you should be able to see how to remove the switch.

You will probably have to get a new switch from toyota or a wreckers.

Good luck :)

May 08, 2009 | 1992 Geo Storm

1 Answer

2006 hyundai sonada need to replace radio


Plastic trim removal tools are required for this job or you will break something. Recommend you refer this job to a Hyundai Dealer.

Mar 27, 2009 | 2006 Hyundai Sonata

1 Answer

How to remove trim from rear hatch door on 2001 Sienna


You need to remove the big plastic or vinyl rear hatch trim to get the side trims off. Remove the 10 mm bolt that holds the pull handle (if you have a pull handle), and then, using a flat tool, (like a stiff putty knife), insert the tool between the vinyl trim and the tailgate to loosen the plastic clips (there is like 18 of them); one the hatch panel is off, you will see that you can now remove the side trims.

Oct 26, 2008 | 2001 Toyota Sienna

1 Answer

Drivers door trim


The handle part of the door panel comes pops off with a butter knife or screwdriver etc. and there will be one or two screws in there. Just be as gentle as you can cause sometimes it leaves marks in the plastic. Good luck!

Jul 22, 2008 | 2005 Ford Focus

Not finding what you are looking for?
1997 Ford F150 Regular Cab Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...