Question about 2006 Dodge Stratus

1 Answer

But a new timing belt on and dont no the timing marks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 22,156 Answers

White paint the gearwheels before you take the old one off??-------remove no 1 plug and use a long thin screwdriver to locate TDC no1 ,you may not be able to engine right round because of valves ,then remove rocker cover and look at valves on no 1 ,they should be fully closed then bring piston to tdc no1 ,there it is simple .then look for the timing marks ,which could be on the end of the cams ,a groove that has to level with the head ,or a lug on one the cam bearings

Posted on Nov 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing belt marks on 1.5 in picture


did the belt break or is this regular maint??? it is an interfearance
head , if it broke the valves will all be bent end of that story.
if you have it apart be very careful turning things (you will hit valves) if old belt is still on ,take a paint marker , mark the belt and cam gears and the crank with one dot one the belt edge and gear face. remove belt ,lay new belt edge to edge and transfer marks exactly onto new belt slip new belt onto cams n crank verify everything is matched to old marks if tensioner is adjustable dont make it to tight or it will "sing" this way if it was running when you shut it off it does not matter where the timing belt marks are because nothing should be out time.

Mar 06, 2015 | 1999 Daewoo Lanos

1 Answer

How to reroute the drivibg belt or fan belt


Hi,just inline the crankshaft to the top dead centre marks,then check that the camshaft marks line up,if they dont line up then turn the crankshaft pully again untill the camshaft marks line up,slacken the timeing belt pully adjuster take belt off and replace with new one,tighten the pully adjuster back up,now put a spanner on the crakshaft pully and turn clockwise untill the top dead centre marks and the camshaft marks inline if they dont then slacken the ajusting pully inline marks again and try again,if marks do inline ok then you are ready to start the car.
hope this helps good luck.

Feb 25, 2015 | Cars & Trucks

2 Answers

The timing belt tensioner failed on my 2000 saturn Ls2 now the timing is off how do i get it back 2 tdc i got new belt n all pulleys but dont want 2 take belt off b4 i know how 2 get the timing back t


Remove Belt.Turn crankshaft pulley mark to line up with mark on housing TDC. Turn camshaft gear mark to line up with mark on head or block housing. More than one mark on cam gear ? If so turn camshaft till number four cylinder inlet and exhaust valves are just rocking this is the mark to use. ( same can be used on a six cylinder engine rocking number six valves ) fit new parts, tension belt, (TIP) now turn engine twice by hand , recheck that timing marks line up . saves a lot of time if you find they don't later.

Sep 16, 2014 | Cars & Trucks

1 Answer

2003 ford ranger need timingmarks my beltbroke


I've never done one on a Ranger, but most timing gears have alignment marks that you line up before you install the belt. Don't forget to replace the belt tensioner while you're at it.

Jul 06, 2014 | 1993 Ford Ranger SuperCab

2 Answers

Timing belt replacement. what are the mark settings on the pulleys?


If you dont know the marks on an engine when replacing the timing belt. There are usually marks on the pulleys and housings to line up. Put the engine on top dead centre TDC from the crankshaft marks before looking for the other marks. If you cant find them Use white out to place your own marks on the pulleys and housings before removing the old belt . To be sure nothing gets out of line mark any pulley that has teeth. It can be useful to take a few digital photos . When fitting the new belt make sure your marks line up again.

Mar 03, 2011 | 1992 Geo Storm

2 Answers

1997 pathfinder i need a water pump do i need to


yes you will have to remove the timing belt and crank pully. It is not as bad as it looks. You might as well, while you are in there, change the thermostat and new Timing belt and tensioner pully.
The trick I use, (and I have done hundreds of Timing belts) I use a good paint pen to mark the timing belt and gears. make sure to mark it so you know what marks are for what cam and crank. and which direction it goes. then on the new belt crefully transfer the marks. then it goes really smooth and there is no guessing hoping it is properly lined up on the factory marks. and you dont have to line every thing up before you take off the belt either. just mark it and remove it where the motor stopped..If you do it this way, you dont have to worry about trying to line up the cams and crank to there respective marks, just the ones you made, then there is no mistake.

Feb 14, 2010 | 1997 Nissan Pathfinder

1 Answer

Timing belt installation alfa 156


remove the fan belt first them start removing the bolts holding on the timing belt cover. once its off you have remove the large pully at the bottom of the engine. Mark up the small pully on the bottom and the two at the top to get your timing, make sure they dont move. release the timing belt tentioner and remove the old belt. you kit should have a new tentioner, idle pully and belt. above all mark sure your timing marks dont move, or your in trouble when you start the car.

Aug 30, 2009 | 2000 Alfa Romeo 156

2 Answers

TIMING BELT MARKS DONT MATCH AFTER ENGINE TURNED OVER


dont worry about that you will have to turn the motor over 40 to 50 time before those timing belt marks line up again if your pulley marks line up correctly thats all you have to worry about

May 29, 2009 | 1994 Toyota Land Cruiser

1 Answer

I need to put a timing belt on a daewwoo lanos


Go to mechanic and ask him to put a new timing belt, its the aftest way.

May 19, 2008 | 1999 Daewoo Lanos

Not finding what you are looking for?
2006 Dodge Stratus Logo

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...