Question about Cars & Trucks

1 Answer

My hitachi cordless has stopped working. pull the trigger nothing. then it turns, then gone. what could it be???

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 399 Answers

Clean the terminals for the battery mount

Posted on Nov 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I decrease the trigger pull on my Kimber


You need to buy a lighter trigger spring. Several websites sell them. Just Google it and find them.

Feb 04, 2015 | Cars & Trucks

2 Answers

Why won't my highlander start.Nothing happens when key turned to start. Starter not turning.


If you went straight to starter with jumper cables and you got nothing then , then pull and have starter bench tested. Also make sure you haven't trigger some kind of security on your system that would lock you out from starting. you should see a security light flashing if you did.

Jan 12, 2015 | 2005 Toyota Highlander

1 Answer

My excavator hitachi ex200-1 weak swing and when you swing then stop vibration begin on turn table when i stop to swing,and when i swing and lift cylinder raise,vibration on the turn table will contin


Not sure would need to have a good look ,but i suspect a safety valve isnt closing properly causing thumping within the hydraulic system which is the vibration you can feel,shouldnt cost a lot to repair providing the faulty valve can be located so return to the dealer as they will have a good idea as yours isnt the first to go wrong iam sure

Sep 24, 2012 | Cars & Trucks

1 Answer

Ignition switch on my c class mercedes has stopped working


check the shifter if it is an automatic and is not in park or neutral properly the the switch will not trigger, making the car think it is still in drive or reverse. Sometimes it is just to wiggle it a bit to trigger the safety switch, or can also be the steering wheel lock, sometimes there can be some friction on the unit and is just to let it off buy turning the wheel slightly to release it. you will have to do this simultaneously with turning the key as when you release the wheel the presser will return.

Jun 09, 2012 | Mercedes-Benz Cars & Trucks

1 Answer

My car is in a locked garage, no sign of entry at all. Last night around mid night my horn and flashers went off repeatedly like a car alarm. When I went to disconnect the battery, it stopped. What is...


This is a malfunction of the alarm system, possible that the processor was triggered. if there was some rodents or creatures that had triggered then it would have gone on till you went around to switch off.... it works for a time period.
Check the leads of the alarm unit, Then ARM the car and try to shake the car to see if there is any reaction to confirm.

Jun 13, 2011 | Ford Taurus Cars & Trucks

1 Answer

I have an 06 canyon. The check engine light keeps coming on. And now there is a warning ding going off with nothing displaying on info center. Brake lights stop work except for the third? Wats going on?


RE: check engine light, stop by any good parts store and have an OBII scan (fault scan). That will pull codes that will identify what triggered light. RE: Brake lights, check wiring in and around tail lights (especially if you have trailer wiring)

Mar 11, 2011 | 2006 GMC Canyon

1 Answer

Car won't start mechanic reset inersha switch care ran for 2 days wouldn't start again then they replaced the fuel pump car ran for 2 days now won't start again


Did the inertia switch get triggered again? On the side panel, down behind the hood-release, there is an access hole in the panel. (1.5in diameter?) Inside you'll find the switch. It's a round button; that acts kind of like the ground default switch on an outlet. If you can push it in; it's been triggered again. If not; well it should be fine.
What triggered it the first time? If it was an accident; there may be further damage.
If that's good to go: I'd have to ask whether the fuel filter was changed at the same time. Sometimes they can clog with debris from burnt-out pump.
I had pump go out in my Mystique. It didn't trigger the inertia switch; but it did stop working two days later, as well. It turns out we messed up the plug connecting to the pump. That would be worth checking as well. You need to pull up the rear seat cushion. Where you'll find a rubber cap with a wiring harness protruding from it. Lift that up you'll find the plug underneath. Unplug it and perform a visual inspection. If it all looks good, well you'll need to begin more advanced diagnostics.
Then again, as cars go; it may not have been the pump to begin with, just a coincidence. Or something else has gone afoul. Dang cars!

Good luck,

Alex

Nov 26, 2010 | 1999 Mercury Mystique

1 Answer

OUR 04 TRAILBLAZER, THE A/C STOPPED WORKING, IT WOULD WORK SOMETIMES AND BLOW COLD AIR NOW NOTHING COMES OUT, OR THE HEATER TOO.. LITTLE AIR WILL PULL THROUGH IF ON THE HIGHWAY, I CAN HEAR IT CLICK OVER...


a couple of things,1 blower motor fuse.2 blower motor gone out.3 switch on fan speed control switch not sending signal to fans.after checking the fuses.next check theswitch on control panel.set ac or heater.if fan still doesnt come on then replace it.when it work and then stops working there are a lot of possiblities that caused the prob relay too not fliping over inside staying close loop.hope this helps.

Aug 16, 2010 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...