Question about 2005 Dodge Ram 2500 Truck
Thats a transmission code, u need to take ur car to a certified workshop to figure it out...
Posted on Nov 13, 2009
All code P0700 means is the Transmission control module has detected a problem in the electronic transmission controls or sensors and has asked the Powertrain contreol module to turn on the Check engine light, u need to have the Trans control module tested for trouble codes, u can't do this without a dealer scan tool.
Posted on Nov 13, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: Error Codes P0700 and P0605
0605 is for an Internal Control Module Read Only Memory (ROM) Error. This is typical of a malfunctioning computer. If the computer is bad, your retrieved codes are probably wrong anyway. May need to replace computer, drive, then see if if your check engine light returns.
Posted on Jun 08, 2009
P0732 Gear 2 Incorrect ratio
P1782 P/ES Circuit Out Of Self Test Range
P1787 2-1 Downshift Error
P0700 Transmission Control System (MIL Request) Malfunction
Here is the deal, u have some serious transmission related faults, in order to sort this out u will need to take this to the dealer, allot of testing is required to get to the bottom of this, if I had to guess I would say the trans is going to have to be overhauled.
Posted on Mar 19, 2009
(DTC) CODE # P0700....Transmission Control System (MIL Request)
Translation: Transmission Control Module (TCM) Malfunction or Failure.
P0700 Information Code
The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.
This code is for information ONLY. If this code is present, check for transaxle codes.
P1776: Solenoid Switch Valve Latched in Low/Reverse Position. The TCM monitors the L/R solenoid to ensure that the fluid transfer happens. It uses a Pressure switch to verify this. Usually this code is set by a switch that is stuck or a solenoid that is not mechanically operating.
A transmission shop would be better suited for this type of work.
Posted on Apr 11, 2009
p0700 indicates you have trans fault present..p1776 is a trans fault which means solenoid switch valve is latched in low/reverse position..solenoid switch valve is located in valve body of transmission,but for 2001-2004 LH vehicles you need transmission event data read to find out what TRS position the fault set..recommend chrysler dealer for this fault..also build code on solenoid pack in trans must be checked..if in a certain build code range,you replace solenoid pack..not the valve body..valve body must be removed to check build code on solenoid pack..i have seen this problem before..i am a dealer technician, and had one of these fault codes last week and solenoid pack was the problem..solenoid pack is about 375 dollars..total time with diagnostics was about 3 hours..
Posted on Jun 14, 2009
There is a TSB for this issue: It is in "limp" mode. It is not unusual for the Sebring - Should be covered by Chrysler.
TSB Number: 0801505
NHTSA Number: 10013731
Posted on Apr 21, 2010
Tips for a great answer:
Jun 28, 2017 | Cars & Trucks
Nov 25, 2016 | Suzuki Cars & Trucks
Mar 06, 2014 | 2008 Kia Sorento 3.3
Sep 07, 2011 | 2002 Dodge Grand Caravan
May 01, 2011 | Suzuki Forenza Cars & Trucks
Feb 21, 2011 | 2002 Dodge Intrepid
Jan 24, 2011 | Saturn Ion Cars & Trucks
Jan 17, 2011 | 2004 Jeep Grand Cherokee
Mar 31, 2010 | 2004 Jeep Grand Cherokee
Feb 15, 2010 | 2002 Dodge Stratus
1,151 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: