Question about 2000 Chevrolet 3500

2 Answers

Got a 2000 chevy 3500 express van how do i get the old ignition switch out to replace it

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 5,081 Answers


Ignition Switch Replacement - On Vehicle

Removal Procedure

Caution: This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:

• Air bag deployment

• Personal injury

• Unnecessary SIR system repairs

In order to avoid the above conditions, observe the following guidelines:
• Refer to SIR Component Views in order to determine if you are performing service on or near the SIR components or the SIR wiring.

• If you are performing service on or near the SIR components or the SIR wiring, disable the SIR system. Refer to Disabling the SIR System.

Disable the SIR system. Refer to Disabling the SIR System in SIR.
Remove the steering column trim covers from the steering column. Refer to Steering Column Trim Cover Replacement - On Vehicle .
Disconnect the steering column electrical connectors.

Remove the wire harness assembly (1) from the steering column and the wire harness strap (2).

Slide the 2 connectors (2) of the turn signal and multifunction switch assembly out of the bulkhead connector (1).



Remove the key alarm connector (1) from the lock module assembly (2) in the following way:
Rotate the key alarm connector (1) 90 degrees.
Pull the key alarm connector (1) out of the lock module assembly (2).
Remove the passkey connector from the lock module assembly (2).

Remove the connector (2) from the electric park lock (1), for vehicles equipped with floor shifters.

Slide the ignition and key alarm switch assembly (3) out of the lock module assembly (1).

Installation Procedure

Slide the ignition and key alarm switch assembly (3) into the lock module assembly (1).

Install the key alarm connector (1) into the lock module assembly (2).
Push the key alarm connector (1) into the lock module assembly (2).
Rotate the key alarm connector (1) 90 degrees so that the key alarm connector (1) locks into place.
Install the passkey connector into the lock module assembly (2).




Snap the electric park lock (2) onto the lock module assembly (1), for vehicles equipped with floor shifters.

Reconnect the connector (2) to the electric park lock (1), for vehicles equipped with floor shifters.

Slide the 2 connectors (2) of the turn signal and multifunction switch assembly into the bulkhead connector (1).

Attach the wire harness assembly (1) to the steering column wire harness strap (2).

Posted on Nov 13, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

Remove the steering wheel , need a puller and locking ring tool, disconnect batt, turn the key to tho on position, and remove bolt that holds the tumbler in,

Posted on Nov 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram chevy van


Fixed Problem (it was my van) no power to ignition wire at starter. Replaced Ignition lock cylinder. just worn down. (Delivery van 50-60 starts a day). 160k miles.

Apr 25, 2013 | 2000 Chevrolet Express Cargo

1 Answer

2000 chevy express 3500 van with a 350. Hard time starting. When it starts runs beautiful! Will only start after several taps of the key as if you where setting timing. Not with key fully turning over....


sounds like the check valve in fuel pump is allowing fuel to drain back out of lines. this would require ystem to prime up each time it is cranked. check fuel pressure it should hold with key off if it leaks down this is problem and pump will need to be replaced

Jun 06, 2011 | 2000 Chevrolet Express Cargo

1 Answer

I have a fuse blowing constantly on my van


you are on a search and destroy mission, i recommend you buy a manual with wiring diagram, at least it will tell you what is hooked on that circuit, thenits a matter of testing wiring, i suspect you have a short somewhere

May 24, 2010 | 2000 Chevrolet Express Cargo

2 Answers

2001 chevy express van 3500 while driving security light comes on dash then engine shuts down , once pulled off the road it will start back up.. did this 3 times on hour drive.. feels like gas pedal just...


You need to get the codes from the theft deterrent module.Usually a B2960.This will help in the diagnosis of the problem.Hope this helps.Good luck.

Apr 07, 2010 | 2001 Chevrolet Express

1 Answer

2000 chevy express 1500 van having starting issues


Start with fuel system. Listen for fuel pump humm at fuel tank No humm check wiring to pump for power. Then check for spark at plugs and wires. Remove wire from coil and hold near engine and see arch when you crank. No arch. Replace ignition Modular inside distributor cap or cap or rotor

Feb 04, 2010 | 2000 Chevrolet Express Cargo

2 Answers

2004 chevy 3500 express passenger van transmission


if ur replacing it remove front grill disconnect both lines and carefully remove retaining clips from radiator if replacement is original eguipt mount & reconnect --if its a universal follow instructions usually cut off fittings and use clamps and hose to hook up

Oct 27, 2009 | 2004 Chevrolet Express

Not finding what you are looking for?
2000 Chevrolet 3500 Logo

886 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...