Question about 2007 Ford Explorer Sport Trac

1 Answer

Wnen I press the 4x4 low range button the light flashes a number of time and then goes out. the transfer case does not engage

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 513 Answers

Have you tried putting it in nutruel then try it

Posted on Nov 13, 2009

Testimonial: "That worked. Thanks for your help. I just got the car and it didn't come with a owners manual."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Silverado 4WD. Service 4WD dash light comes on after engaging 4WD and acts up by engaging itself randomly for several days, then goes back to normal.


Check connection at the 4X4 control module , check power and grounds . Do you know how to do basic electrical testing ? Does your truck have manual or automatic trans mission ? Which transfer case does yours have ?

The NVG 263 transfer case features a three button shift control switch located on the instrument panel. When the ignition is in the RUN position, the transfer case shift control module (TCCM) starts monitoring the transfer case shift control switch to determine if the driver desires a new mode/gear position. At a single press of the transfer case shift control switch, the lamp of the new desired position begins flashing to inform the driver that the TCCM has received the request for a new mode/gear position. The lamp continues to flash until all shifting criteria has been met and the new mode/gear position has been engaged. Once the new mode/gear position is fully active, the switch indicator for the new position remains ON constantly. In the event that the TCCM can not or will not complete the shift, the indicator returns to the previously selected position; this is a Transfer Case Shift Control Switch Indicator Flashes, then Returns to Previous Mode condition.

The NVG 263 transfer case provides the driver with 4 manual mode/gear positions:
• 2HI - 2 Wheel Drive high range
• 4HI - 4 Wheel Drive high range
• 4LO - 4 Wheel Drive low range
• Neutral
Have it check for DTC'S - diagnostic trouble codes ?

DTC B0790
DTC B2725
DTC C0306
DTC C0327
DTC C0359
DTC C0379
DTC C0550

Your best bet would be take it to a qualified repair SHOP

Dec 28, 2016 | Cars & Trucks

1 Answer

4x4 will not engage


this may assist you engage in 4x4 and reverse for a few meters, normally this does the trick on the transfer case if not then either the electrics/switch to the transfer case is not not functioning or the transfer case itself.

Feb 03, 2014 | GMC Sonoma Cars & Trucks

1 Answer

I have an 2004 chevy blazer 4x4 and the four wheel drive does not engage on the fly and it also will not engage when in neutral. Four wheel low will work but when you press 4 wheel hi it blinks twice and...


Which of these does your vehicle have ?
The NVG 233 transfer case features a 3 button shift control switch, located on the instrument panel.
The NVG 236 transfer case features a 4 button shift control switch located on the instrument panel.
Do you know what DTC'S - diagnostic trouble codes are ? Both of these 4X4 systems can set DTC'S , Having a professional or factory scanner is what is needed to check for these codes . Not a OBD 2 code reader or autozone , advance etc... The four button system can set a bunch of them .
DTC B2725
DTC C0300
DTC C0305
DTC C0308
DTC C0309
DTC C0310
DTC C0315
DTC C0323
DTC C0324
DTC C0327
DTC C0362
DTC C0367
DTC C0374
DTC C0376
DTC C0387
DTC C0550
DTC C0611

The NVG 233 transfer case features a 3 button shift control switch, located on the instrument panel. When the ignition is in the RUN position, the transfer case shift control module starts monitoring the transfer case shift control switch, to determine if a new mode/gear position has been selected. At a single press of the transfer case shift control switch, the lamp of the new position begins flashing to inform the driver that the transfer case shift control module has received the request for a new mode/gear position. The lamp continues to flash until all shifting criteria has been met and the new mode/gear position has been reached, or has engaged. Once the new mode/gear position is fully active, the switch indicator lamp for the new position remains ON constantly.
The NVG 233 transfer case provides the driver with 3 manual mode/gear positions:
• 2HI - 2 Wheel Drive high range
• 4HI - 4 Wheel Drive high range
• 4LO - 4 Wheel Drive low range
Any of these mode/gear positions may be selected while driving the vehicle. However, the transfer case will not allow a shift into, or out of, 4LO unless the following criteria has been met:
• The engine is running.
• The automatic transmission is in Neutral, or the clutch pedal is applied on manual transmissions.
• The vehicle speed is below 5 km/h (3 mph).


Finding out what if any codes are stored should be your first step .

Feb 22, 2018 | 2001 Chevrolet Blazer

1 Answer

94 explorer, manual trans. last night while driving, 4x4 and low range lights flash on then off. when I shifted into 5th getting on freeway, lose all drive power as if clutch suddenly went out. 4x4 light...


It sounds like the bearings inside the transfer case are going out, with pressure on it while accelerating its fine, then when you push in the clutch the transfer case gets slack allowing the internal parts to move, causing the lights to flash as gears move causing the shift motor to move. I would start looking for a replacement transfer case.

Feb 18, 2011 | 1994 Ford Explorer Limited

1 Answer

04 tahoe z71 the allwheel drive,2wheel drive,and 4hi,4lo buttons don't alwas work sometimes it's in 2wheel drive then go to 4lo and when i push the 2wheel button it just blinks and the 4lo button stays on...


Pulling code's from the 4X4 control module would point to a diagnostic procedure . Do you own a professional type scan tool that can read DTC'S - diagnostic trouble code's in the 4X4 control module ? Autozone , advance etc.... can not read these code's .
Which transfercase does it have ?
Transfer Case - BW 4482-NR4
Transfer Case - NVG 246-NP8

How many buttons for 4X4 three or four ?
The BW 4482 transfer case features a 3-button shift control switch located on the instrument panel
The NVG 246 EAU transfer case features a 4 button shift control switch located on the instrument panel
When the ignition key is in the RUN position, the transfer case shift control module monitors the transfer case shift control switch to determine if the driver desires a new mode/range position. At a single press of the transfer case shift control switch, the lamp of the new desired position will begin flashing to inform the driver that the transfer case shift control module has received the request for a new mode/range position. The lamp will continue to flash until all shifting criteria has been met and the new mode/range position has been reached, or has been engaged. Once the new mode/range position is fully active, the switch indicator lamp for the new position will remain ON constantly.The 4X4 system with four button shift control can set a number of DTC'S
DTC B0790
DTC B2725
DTC C0300
DTC C0305
DTC C0306
DTC C0321
DTC C0327
DTC C0359
DTC C0374
DTC C0379
DTC C0550
The three button switch can also set an store a few codes
DTC B0790
DTC B2725
DTC C0306
DTC C0327
DTC C0329
DTC C0359
DTC C0550
Without knowing if any of these DTC'S are stored can't suggest any type of repair .

Dec 29, 2017 | 2004 Chevrolet Tahoe

1 Answer

When I push the 4x4 push button the light comes on but will not engage the transfer.


Transfer case motor is probably sticking, try hitting the 4x4 low first, or if you can tap on it and try pressing 4x4 button should work.

Jan 20, 2011 | Ford F-150 Cars & Trucks

1 Answer

4x4 lights flash, will not engage into 4wd When switching to 4 high or low the lights come on on the dash but then will go off again. The transfer case does not engage into 4 wheel drive in high or low. I...


This is called the selector motor and you may be correct this is a common problem with these trucks the selector motor goes bad and will not engage the correct gear setting you select.

Jul 10, 2010 | 1996 Ford Explorer

1 Answer

4x4 will not engage on my 1990 Bronco. Light does


It could be the switch, a fuse, a relay, the motor that engages the transfer case (very common problem) or the transfer case itself. Disconnect the motor arm from the transfer case and see if you can move the shift rod by hand. If you can then you know the transfer case is probably OK and you can test from the motor back to the switch.

May 03, 2010 | 1990 Ford Bronco

1 Answer

4x4 indicator flashing all the time wnen not engaged


2001 Mitsubishi MONTERO 01 - Transfer Case > POWER TRAIN : TRANSFER CASE (4-WHEEL DRIVE) [Part 104000 ]
TSB No: 0223007 NHTSA ID: , November 01, 2002 : Replacement:
Summary: 4wd indicator lamp flashing / diagnostic trouble code (dtc) 33.

2001-02 Montero
A flashing 4WD indicator lamp and/or DTC 33 may be caused by corroded transfer case shift position switches. The original switches are susceptible to water damage, and new revised switches are available to prevent the problem.

PROCEDURE

1. Replace the five transfer switches

2. Clear the DTC, using the scan tool.

3. Test drive the vehicle to confirm the 4WD indicator lamp does not flash and DTC 33 does not reset.

Apr 08, 2009 | 2001 Mitsubishi Montero

1 Answer

4x4 not engaging


air line from under battery to fire wall falls to bits

Mar 18, 2009 | 2001 Chevrolet Blazer

Not finding what you are looking for?
2007 Ford Explorer Sport Trac Logo

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...