Question about 2002 Buick Regal

1 Answer

How to open the car w/o a key fob

We only have the ignition key, the key fob is dead, and we can't unlock the car to get in.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 119 Answers

Go dealer with vin number and id and they can cut you a key

Posted on Nov 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to unlock a 1998 bmw 528i with a dead battery


Ignition key works the manual door lock:
You get out the original fob... pull out the (metal) key... insert it into the single lock slot under the drivers side door handle...
and twist like an old fashion key lock.





1998 bmw 528i key with dead fob Bing video

Apr 07, 2016 | BMW Cars & Trucks

1 Answer

My key will not start my car,then it wouldn't open the door


This model year comes equipped with Keyless Enter-N-Go, which uses an electronic transmitter in the key fob to communicate with the car. The vehicle's doors will not unlock and the vehicle will not start if the key fob is not matched to the vehicle or if the commonly-available watch battery in the key fob has been depleted. The EVIC will flash a message upon vehicle startup if it determines that the battery in your key fob is low on charge and should be replaced.

To open the doors, try the following:

1. Use the spare key fob that came with the vehicle. If the battery in your main key fob is depleted, the spare key fob's battery may still retain charge due to its much more occasional use.

2. The key fob comes with an emergency key inside of it. To remove the emergency key, slide the mechanical latch on the back of the key fob sideways with your thumb and then pull the key out with your other hand. This key will allow you to unlock the driver's side door and glove compartment. It will not start the vehicle.

To start the car with a severely-depleted key fob battery, try the following:

1. In case the ignition switch does not change with the push of a button, the RKE transmitter (Key Fob) may have a low or dead battery. In this situation a back-up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the Key Fob against the ENGINE START/STOP button and push to operate the ignition switch.

To replace the battery in your key fob, try the following:

1. Remove the emergency key from the key fob following the directions above.

2. Using a vinyl spudger tool or a flat-bladed screwdriver, gently pry the two halves of the key fob apart at the indented slot above the slot for the emergency key.

3. Replace the depleted battery with a new battery. Use the depleted battery to visually match the size. The battery is usually available wherever watch or hearing-aid batteries are sold.

4. Snap the key fob back together and replace the emergency key. If the issue is a depleted battery, your key fob should operate normally.

If the issue is not related to the state of the battery, you will probably need to contact your local dealer for service.

Source: Owner's Manual, pages 12-17

http://justgivemethedamnmanual.com/dodge/dodge-charger-owners-manual/

Mar 01, 2014 | 2011 Dodge Charger

2 Answers

Chrysler crossfire key fob will not work to lock, unlock or panic


Put key ignition press unlock or lock 2 times then turn key to accessory position within 30 seconds. Your FOB should work properly.

Jul 25, 2012 | 2006 Chrysler Crossfire

2 Answers

I have a 2007 Toyota RAV 4 I can't get the remote to work after changing the battery does it have to be reset if so what has to be done. I can lock and unlock the doors manualy but not with the remote...


1. get in the car
2. shut the door
3. place the key in the ignition
4. lock the doors, manually
5. turn the ignition to on then off...do this seven times
6. unlock the doors and try your remote

Sep 20, 2011 | 2006 Toyota RAV4

1 Answer

Battery in key fob went dead need to reset keyfob audi tt 2000


hi you can do this but you will have to have a key that does not have a remote/fob on it ( basically just go get one cut cheaply ) then to reprogram keys/key fob's first using the key without fob, turn ignition on ( do not turn over, just to position 2) then lock drivers door with other key ( do not use fob, just the key itself with fob now complete the following within 30 seconds within 5 seconds( of locking the car) press the unlock button on the first key once ( this programs that key as key memory1) the indicators should flash once to indicate signal received wait 5 seconds then press unlock on key fob vehicle should then unlock meaning key fob has been programmed and programming ended open door turn ignition off , and that's it, it should work if you have more than 1 key with fob, do the same as above but instead of pressing unlock once, you do it twice, if third key 3 x if fourth key 4 x etc etc,

Sep 20, 2010 | Audi TT Cars & Trucks

1 Answer

1999 porsche 996 replaced key fob battery disconnected battery now trunk releses are locked and cant access battery.How do you open frt trunk manually


Assuming the car battery is ok (if not, buy a male to male cigarette lighter at the auto store and connect to another car until charged enough to unlock the doors...but don't try to crank the ignition!). The trunks won't open if the battery went dead with the alarm set because arming the alarm physically locks the releases.

Sounds like the key code is switched off because you replaced the key fob battery. Try unlocking the car manual with the key in the door lock. Then switch the ignition on to reactive the keyless entry. If this does not work, you might also try pressing the fob unlock button with the key in the door lock until the dash led flashes.

Jun 10, 2010 | 1999 Porsche 911 Carrera

3 Answers

My wife is stuck at the airport. the key fob on


On the driver's side door handle, there is a cap covering the key hole on the right side. On the bottom of the cap is a small ****. Use the valet key to pry it up and off. Then you may open the door, most likely sounding the alarm, so you will need to insert the remote in the ignition to stop the NOISE!!!! Hope this helps. This is how I lock my remote away when I go somewhere to run.

Nov 06, 2009 | 2006 Volkswagen Passat

1 Answer

Need to re-program 2000 Chev.C3500 key fob need help


1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Jun 09, 2009 | 1999 Chevrolet Tahoe

3 Answers

TWO KEY FOB IS NOT WORKING ONLY ONE


Have all keys with you inside the car and repeat again with the second key within 30 seconds...... "Press and hold the 'unlock' button while at the same time pressing the center 'lock' button three times. On the third time, release the 'lock' button at the same time you release the 'unlock' button." If you have a key with three buttons, ensure doors are unlocked. Put key in ignition and turn key over to 2d position where dash lights, etc come on. Pull key out. Press and hold the "unlock" button while at the same time pressing the center "lock" button three times. On the third time, release the "lock" button at the same time you release the "unlock" button

May 20, 2009 | 2003 Mini Cooper

Not finding what you are looking for?
2002 Buick Regal Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...