Question about 2005 Hyundai Accent

2 Answers

Removing rear wheel hub on hyundai getz 1.3 inorder to replace break shoes.I tried tapping hub from back not budging

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 97 Answers

If you mean the drum then hit it in the front between the lugs should jar it loose. give it a good wack

Posted on Nov 13, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 132 Answers

THERE IS A RUBBER PLUG SLOT ON THE BACKING PLATE, TAKE IT OUT AND LOOK INSIDE OF IT YOU WILL SEE A GEAR PUT A LARGE SCREW DRIVER INTO IT AND TURN IT GOING UP THIS WILL TAKE THE PRESSURE OFF OF THE SHOES

Posted on Nov 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I release the emergency break for towing?


Try jacking rear wheels and rotate wheels if no rotation strip hubs free brake shoes or remove shoes put back together and tow away

Apr 30, 2015 | Cars & Trucks

1 Answer

How do I remove the rear brake drums in a 1991 Holden Barina? There is nothing to back off the shoes and it doesn't want to budge. It freely rotates so don't thimk the shoes are grabbing at all.


Some brake drums are held on by the wheels and this allows the drum to rust onto the axle hub/flange. Spray the wheel studs with WD-40 or CRC and then hit the drum between the studs with a hammer. A good hard rap will jar the drum loose on the studs and break the rust binding .

Dec 13, 2013 | 1992 Holden Barina

1 Answer

How do I get the rear spindle off so I can replace the emergency brake shoes on my 2006 chrysler pacifica?



Adjustment

  1. Place parking brake lever in -full released- position.
  2. Raise and support vehicle.
  3. Remove plug in parking brake shoe support to access adjuster star-wheel.
  4. Through the access hole, rotate the adjuster star wheel in the following direction to expand the shoes outward against the drum:
    1. Left brake - Rotate star-wheel toward rear of vehicle.
    2. Right brake - Rotate star-wheel toward front of vehicle.
  5. Using an appropriate tool, turn adjuster star wheel until wheel will not rotate (dead lock).
  6. Back off adjuster six detents (teeth).
  7. Rotate wheel, checking for light drag. If drag is too heavy, continue to back off adjuster one detent at a time until light drag is present. Do not back off star-wheel more than 17 detents from wheel lock.
  8. Install access plug.
  9. Adjust opposite wheel parking brake shoes using same method.
  10. Lower vehicle.
  11. Apply and release parking brake lever once to ensure proper operation of parking brakes.


Removal & Installation NOTE The following procedure may be used to remove shoes on either side of the vehicle.

  1. Lock out automatic adjuster in parking brake lever.
  2. Raise and support vehicle.
  3. Access and remove rear hub and bearing.
  4. Remove parking brake cable bolt at knuckle.
  5. Completely back off parking brake shoe adjustment.
  6. Remove parking brake shoe adjuster spring.
  7. Remove shoe adjuster.
  8. Remove upper brake shoe hold-down clip and pin.
  9. Remove lower brake shoe hold-down clip and pin.
  10. Remove upper and lower shoes with return spring from shoe actuator.
  11. Remove return spring from shoes.

    0996b43f80204c12.jpg

    Fig. View of the actuator (1), support (2), adjuster spring (3), return spring (4), caliper adapter (5), shoes (6), hold-down clips and pins (7) and adjuster (8)

To install:
  1. Install return spring between upper and lower shoes.
    NOTE Before installing shoes on actuator, make sure actuator hooked to rear cable is positioned with word -UP- facing outward.
  2. Install upper and lower shoes with return spring on shoe actuator located on parking brake cable.
  3. Install lower brake shoe hold-down pin through rear of support and lower shoe, then install hold-down clip.
  4. Install upper brake shoe hold-down pin through rear of support and upper shoe, then install hold-down clip.
  5. Install shoe adjuster. Place end of adjuster with star wheel upward.
  6. Install parking brake shoe adjuster spring.
  7. Install bolt securing parking brake cable to knuckle and tighten bolt to 21 ft. lbs. (28 Nm).
  8. Using Brake Shoe Gauge, Special Tool C-3919, or equivalent, measure inside diameter of parking brake drum portion of rotor.
  9. Place Gauge over parking brake shoes at widest point.
  10. Using adjuster star wheel, adjust parking brake shoes until linings on both park brake shoes just touch jaws on gauge. This will give a good preliminary adjustment of parking brake shoes, before a final adjustment is made at end of this procedure.
  11. Install hub and bearing with wheel speed sensor as well as all components necessary to access it.
  12. Lower vehicle.
  13. Unlock automatic adjuster in parking brake lever.
  14. Perform final adjustment of parking brake shoes

  15. Adjustment This vehicle is equipped with permanently sealed rear wheel bearings. There is no periodic lubrication or maintenance recommended for these units.


    Removal & Installation

    1. Raise and support vehicle.
    2. Remove wheel mounting nuts, then tire and wheel assembly.
    3. If equipped with AWD:
      1. Remove cotter pin, nut lock and spring washer from half shaft.
      2. While a helper applies brakes to keep hub from turning, remove hub nut and washer.
    4. Remove brake caliper and rotor from hub and bearing assembly.

      0996b43f807cb548.jpg

      Fig. Hub assembly

    5. Disconnect vehicle wiring harness connector at wheel speed sensor connector.
    6. Unclip wheel speed sensor connector from spare tire mounting support.
    7. Disconnect two sensor cable routing clips on rear suspension crossmember.
    8. Disconnect two sensor cable routing clips along toe link.
    9. Disconnect sensor cable from bracket on brake support.

      0996b43f807cb54d.jpg
    10. Completely loosen, but do not remove four bolts fastening hub and bearing in place. Once loosened from threads in hub and bearing, push bolts up against rear of hub and bearing to keep brake support plate in place when hub and bearing is removed.

      0996b43f807cb54e.jpg

      Fig. Rear hub and bearing mounting bolts

    11. Pull hub and bearing off knuckle and half shaft (if equipped with AWD), then thread wheel speed sensor cable through hole in brake support plate as it is removed with hub and bearing.
      0996b43f807cb54f.jpg
    To install:
    1. Position hub and bearing bolts though rear of knuckle and parking brake support just enough to hold support in place as hub and bearing is installed.
    2. Install hub and bearing by first feeding end of wheel speed sensor cable through hole in bottom of parking brake support. As this is being done, if equipped with AWD, slide hub and bearing onto half shaft. Place hub and bearing through brake support, onto knuckle, lining up mounting bolt holes with bolts and placing wheel speed sensor head at bottom.
    3. Install four bolts fastening hub and bearing in place. Tighten mounting bolts to 60 ft. lbs. (81 Nm).
    4. Place wheel speed sensor cable routing grommet into bracket on parking brake support.
    5. Route wheel speed sensor cable along toe link and rear suspension crossmember connecting routing clips where shown.
    1. Connect vehicle wiring harness to wheel speed sensor connector.
    2. Install brake rotor and caliper.
    3. If equipped with AWD:
      1. Install washer and hub nut on end of half shaft.
      2. While a helper applies brakes to keep hub from turning, tighten hub nut to 180 ft. lbs. (244 Nm).
      3. Install spring washer, nut lock and cotter pin on end of half shaft.
    4. Install tire and wheel assembly. Install and tighten wheel mounting nuts to 100 ft. lbs. (135 Nm).




May 18, 2011 | 2006 Chrysler Pacifica

2 Answers

How to replace the rear break drums on a hyumdai accent gs


Brake Drums-They seem to be fastened with a nut and have bearings that need to be regreased based on the diagram found for replacing the shoes. Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Wheel 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
To Install:
  1. Install or connect the following: 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
    • Wheel
--- Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Wheel 02-04_hyundai_accent_brake_drum.gif

    • Brake drum 02-04_hyundai_accent_rear_brake_backing_plate.gif

    • Shoe hold-down spring
    • Automatic adjuster spring
    • Adjuster lever
    • Shoe adjuster by spreading the shoes
    • Shoe to shoe spring
To Install:
Note: Apply the specified grease to the shoe to backing plate and shoe to anchor plate contact surfaces.
  1. Install or connect the following: 02-04_hyundai_accent_rear_brake_backing_plate.gif

    • Shoe hold down pin
    • Return spring to the push rod while it is shortened
    • Shoe hold down spring
    • Shoe to shoe spring
    • Shoe adjuster by spreading the shoes
    • Adjuster lever
    • Automatic adjuster spring 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
    • Wheel
Note: After assembling the drum components, pull the parking brake lever all the way up several times
prev.gif next.gifprev.gif next.gif

Sep 30, 2010 | 2001 Hyundai Accent

1 Answer

I want to remove right rear wheel to check brake shoes. big central nut hard to remove.


You do not need to remove that nut to check your breaks. That nut removes the whole hub assembly. Don't mess with it.

Now you have what are called drum brakes on the rear of your car. The front has disk breaks. Take some wd-40 and spary on the lug bolts and the center hub. Let it soak for a bit and then take a hammer and tap around on the drum to free it up. your break pads are on the inside of that drum.

Sep 16, 2009 | 2000 Hyundai Accent

1 Answer

Changing front and rare break pads in hyundia excel


this front::
  1. Raise and support vehicle, then remove wheel/tire assembly.
  2. Remove lower bolt and caliper assembly. Position assembly aside using suitable wire.
  3. Remove brake pads and shim.
  4. Bottom piston in caliper using suitable tool.
  5. Install new brake pads and attach shim to the outer pad. Tighten lower bolt to specifications.
this for rear::

1. Raise and support vehicle, then remove wheel/tire assembly.
  1. Remove axle nut, then the hub and drum assembly.
  2. Remove end shoe springs, cylinder and hold-down spring.
  3. Remove shoes and adjuster as an assembly.
  1. Reverse removal procedure to install, noting the following:
    1. Apply suitable grease to backing plate shoe contact surfaces.
    2. Install shoe hold-down pin, then assemble return spring with the pushrod shortened.
    3. Pull parking brake lever fully upward. Repeat process several times.

Jun 04, 2009 | 1994 Hyundai Excel

1 Answer

I have a 2003 mercury marquis. Both rear hubs


If you have the caliper and retaining rings off the park brake must be holding it. This vehicle has small parking brake shoes that apply to the inside of rotor hat. Try backing off the adjustment and tap the sides of the hat to free them up.

Mar 22, 2009 | 1996 Mercury Grand Marquis

1 Answer

1992 626 Rear Drum stuck


Does it have a dust cap in the center? If so, pry it off and remove the nut. It also might have a reverse thread (check). If it doesn't have the cap, then you might have to cut the drum in half. But I am almost positive that it does have the metal dust cap in the center of the hub/drum. I sincerely hope that this helped you. Let me know how things went. I'll still be here if you need me.
Bryon

Mar 20, 2009 | 1989 Mazda 626

1 Answer

2002 Hyunsai Accent rear brakes, do you have to remove wheel hub


Yes, it should be removed it makes the job a lot less difficuilt. 

Nov 30, 2008 | 2002 Hyundai Accent

3 Answers

Dodge Magnum Brake Rotor


You need to back off the hidden emergency brake shoes that contact the interior part of the rotor. Remove the rubber plug on the inside and rear part of the hub and use a screwdriver to back off the star wheel adjuster. Unless you do this, you'll never get the rotors off.
Hint: the secondary drum type emergency/parking brake shoes may need replacement

Jul 18, 2008 | 2006 Dodge Magnum

Not finding what you are looking for?
Cars & Trucks Logo

547 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...