Question about 1992 Toyota Pickup

2 Answers

Can anyone tell me how to bleed a master cylinder for a 2001 isuzu rodeo with abs? can i bleed the master cylinder with it being attached to the power assist, or do i have to bench bleed it?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 22,095 Answers

Just bleed it as normal starting at the master cylinder first ,tighten all the pipes hand tight ,fill with fluid then assistant pushes pedal down and holds it down tighten pipes then pedal up wait 10secs and push pedal down again and slacken pipes ,repeat till you see no more air ,then bleed as normal

Posted on Nov 13, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

You definitely have to bench bleed the master cylinder, and once you have replaced it in the vehicle, you will need to bleed the brakes from the calipers to remove any additional air.

Posted on Nov 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abs light on and pedal will not compress without pumping when I first start the car. Drives fine after. 2004 Isuzu rodeo 3l


pumping means the MC is bad, or there are leaks.
look for leaks takes what 5min?
if no leaks on ground
or on tires.
or both sides of fire wall below, MC then the MC is bad. (leaks inside at seals inside (worn out)
mc is the MASTER cylinder.
my post assumes brakes were not molested, or needs bleeding due to that.

Jan 27, 2015 | Isuzu Cars & Trucks

1 Answer

I have bleed the rear brakes multiple times but still get air and "soft" pedal requiring multiple pumpimg. How do I bleed them if they are anti lock brakes? 2000 Isuzu Rodeo


It's pretty much the exact same process just remove your abs relays/fuses
if the brake bleeding doesn't work it sounds like you may need a new master cylinder

Mar 13, 2014 | 1996 Plymouth Voyager

1 Answer

Trying to find leak in clutch system os 1993 rodeo need diagram


Did you bench bleed the master or slave cylinder ? Is Your Brake pedal Hard ? Could be your Brake booster . send image for more understanding of your problem

Feb 25, 2014 | 1993 Isuzu Rodeo

1 Answer

Soft brakes


You have a leak in the brake system, need to check the medal brake lines that run through the frame rail and goes to the back wheels, It is common for those to rust into towards the back. If lines are okay then check the wheel cylinders. If you are not low on brake fluid then you probley have a bad master cylinder.

Apr 21, 2012 | 2000 Isuzu Rodeo

1 Answer

2001 Rodeo 6 cylinder. ABS light comes on when I start car. Have had the brakes check and they tell me there is no problem. Car has about 115,000 miles on original brakes but I am told it still has...


The ABS will come on and stay lit for a couple seconds when you start the car. It should then extinguish. This is normal operation. If it stays lit there is a problem and the ABS will not be available, although the brake system is still fully operational. Leave a message if this is not solved.

Aug 02, 2010 | 2001 Isuzu Rodeo

2 Answers

My brakes do not release immediately on my Rodeo


You need to find out if it`s just one brake that`s sticking on or if it`s the pair diagonally connected to each other or if it`s all four. If it`s just one, it`ll be the cylinder or associated components to that one brake or a crushed pipe. If it`s two diagonally opposed to each other, it could be the brake compensator located on or near the rear axle (May not have one due to having ABS) or the master cylinder to that circuit or a crushed pipe. If it`s all of them, it can only be the master cylinder/booster sticking pedal or again a crushed pipe. Ian

Jul 30, 2009 | Isuzu Rodeo Cars & Trucks

2 Answers

Bleeding Brakes on a 2001 Silverado Z71


Tony,

When bleeding brakes after the system has been opened for service (you didn't say if you were doing any work on the master cylinder) you should start with the farthest wheel away from the master cylinder, which is the righ rear. Fill the master cylinder, then have an assitant "pump up" the brake pedal. Tell them to hold it down firmly, then open the bleeder on the wheel cylinder(s). Do not release the brake pedal until you have closed the bleeder valve again. You'll know when the air is out - there won't be any more bubbles. Since this vehicle is 2001, this would be a great opportunity to flush the system. Just make sure you have enough brake fluid (DOT 3 or 4, depending on your vehicle). Good luck!

Mar 15, 2009 | 2001 Chevrolet Silverado

1 Answer

2002 Rodeo 4x2 LS (ABS Light is on)


Don't be cheap. Get some decent tires. About your ABS light, you might either have a master cylinder that's going bad or your pads are worn and ABS sensors are trying to tell you to have your brakes serviced.

Jul 17, 2008 | 2002 Isuzu Rodeo

Not finding what you are looking for?
1992 Toyota Pickup Logo

198 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...