Question about 2000 Volkswagen Golf

1 Answer

Accessive rear brake wear. Rear pads wear out twice as fast as the front pads...

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 399 Answers

Are your wheels getting hot if so your wheel cylinder is sticking

Posted on Nov 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My back breaks wear out twice as fast as the front. Why?


Could be your rear brake cable is bad,causing your brakes to wear more,

Sep 25, 2015 | Jeep Wrangler Cars & Trucks

2 Answers

I have to continuously replace calipers on my jeep, what is the problem?


wonder if the rotors are too slim. If this happens the brakes get too hot as the rotor radiates away the heat. If too hot the brakes could wear out faster.

Aug 16, 2015 | 2003 Jeep Grand Cherokee

1 Answer

Rear brakes dragging


Normally I would say check the brake hose, but that would only be for one wheel.
If the rear brakes are not releasing normally, either something is keeping pressure applied, or the calipers are not sliding back. If both inner and outer pads are wearing down equally on both wheels, I would look for a pressure problem. If only the outboard pads are wearing, the calipers are sticking in place.

Jun 28, 2013 | Cars & Trucks

1 Answer

Change brake pads


For starters the front and rear us disk pads and it is not hard to do. On the front jack up the front and us jack stand for safety. After you take of the wheel remove the two bolts at the back of the brake caliper remove the caliper and then the old pads us a C- clamp with one of the old pads installed in the caliper then just us the c-clamp to push the cylinder all the way in until it will go no further install new pads put back on. But before you do the next side hit the brake to push the cylinder back out. Go to other side do the same thing. On a side not you only need to replace the rear brakes every other time you do the front. The front wear twice as fast as they do most of the stopping.

May 19, 2013 | 2004 Buick Century

1 Answer

FRONT BRAKE PADS WEAR FAST. THEY APPEAR TO RUB ALWAYS


u mite be riding the brakes.front wear faster than backs do.

Nov 26, 2012 | 2003 Jeep Liberty

1 Answer

Rear brakes engage while traveling


check your e-brake cable sounds like it is stuck

May 05, 2012 | 2007 Dodge Nitro R/T New Cars

1 Answer

Adjusting 2007 aveo rear brakes


do not attempt any adjustments. replace the front brakes when they need it. if you try to adjust the proportioning valve you will lock up your back brakes and risk loosing control of your vehicle. you risk ruining the ABS system in your car which will cost you far far more to replace than a cheap set of brake pads. the front brakes do most of the stoping, that is why they wear out much faster than the back brakes. it is VERY IMPORTANT that you DO NOT attempt to adjust your brake proportioning valve.

Mar 08, 2012 | 2007 Chevrolet Aveo Sedan

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

Front brake pads wear down too quick


Get the brake calipers checked, the slides are probably seized/sticking causing drag.Check the rear hubcap for stones/debris/looseness.There is also a brake snow/debris guard which tends to rust.

Feb 28, 2010 | Dodge Caravan Cars & Trucks

3 Answers

At what mileage should the rear brakes be replaced? Is it common for the rear brakes to be replaced at less than 22,000 miles on a 2007 Sonata gls?


Most of the stopping power goes to the front of the car. You usually go thru two sets or sometimes three sets of front pads before you need to change the rear brakes. It sounds odd the rear brakes need to be replaced at 22,000. havee the front brakes been replaced before?

Sep 17, 2009 | 2007 Hyundai Sonata Limited Sedan

Not finding what you are looking for?
2000 Volkswagen Golf Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...