Question about Chrysler PT Cruiser

1 Answer

Cylinder head bolts torque specs and sequence, and rocker arms, valve cover bolts.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 192 Answers

Cylinder head bolts: 1st - step; - 25 ft./lbs. 2nd - step; - 50 ft./lbs. 3rd - step; - 50 ft./lbs. 4th - step; - turn 90 degrees
STARTS FROM CENTER AND WORK IN A CLOCKWISE MOTION..

SORRY BUT OTHERS DON'T HAVE SPECS. REALLY CAN GET AWAY WITH OTHERS JUST BY VALVE LASH AND HAND TIGHT VALVE COVER......HOPE I HELPED


Posted on Nov 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flywheel torque spec's for 1983 Ford F-100


Could it be a F-150 instead?
Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Ford Cars & Trucks

1 Answer

Torque spec's for the fly wheel


Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Cars & Trucks

1 Answer

Rocker arm pivot torque for olds cutlass 1987 307


Oldsmobile Torque Specs - GbodyOlds.com

www.gbodyolds.com/forum/showthread.php?754-Oldsmobile-Torque...
Feb 7, 2013 - 2 posts - ‎2 authors Oldsmobile Small-Block Engines Cylinder Head Bolts (1/2in. bolt) 130 ft. lbs. Cylinder Head ... Rocker Arm Pivot Bolt 25 ft. lbs. Rod Bearing ...

Rocker Arms - AutoZone

www.autozone.com/...Cutlass...1987.../Rocker-Arms/_/P-0900...

AutoZoneGM Cutlass RWD 1970-1987 Repair Guide ... To remove the rocker arms from the shaft, the nylon arm retainers must be removed. ... 7: Engine valve system, 260, 307, 350, 403 Oldsmobile built engines ... Unfasten the two bolts that attach the rocker arm pivot to the cylinder head. ... Torque the retaining bolts to 25 ft. lbs.

Dec 01, 2015 | 1987 Oldsmobile Cutlass Salon

1 Answer

I need to know the torque specs for the head gasket for a 99 2.2 pontiac sunfire


Install cylinder head bolts finger-tight. New cylinder head bolts are recommended due to stretch of the old bolts.
Tighten bolts in sequence, tighten the long bolts to 46 ft. lbs. (63 Nm) plue 90 degrees. Tighten the short bolts to 43 ft. lbs. (58 Nm)


Install pushrode and rocker arms and rocker arm nuts. Tighten nuts to 22 ft. lbs. (30 Nm).


Install valve cover and tighten bolts to 89 inch lbs. (10 Nm).

Apr 05, 2011 | 1999 Pontiac Sunfire

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    1 Answer

    NEED HELP WITH TORQUE SPECS ON 1998 CHEVROLET SURBURBAN CYLINDER HEADS 5.7


    Cylinder Head Removal & Installation 5.7L Engine To Remove:
    1. Disconnect the negative battery cable.
    2. Drain the engine coolant.
    3. Remove the air cleaner assembly.
    4. Remove the upper radiator hose.
    5. Remove both heater hoses.
    6. Disconnect spark plug wires at distributor cap.
    7. Remove distributor cap.
    8. Remove the coolant bypass hose from the water pump.
    9. Remove the drive belt. NOTE: It is not necessary to evacuate the A/C refrigerant.
    10. Remove the A/C compressor from the mounting bracket and set it aside.
    11. Remove the wiring bracket from the rear of the cylinder head.
    12. Disconnect the accessory bracket and slide forward.
    13. Remove the upper and lower intake manifold.
    14. Remove the exhaust manifolds.
    15. Remove the valve rocker arms and pushrods.
    16. Remove the power steering pump pulley.
    17. Disconnect the electrical connector from the power steering pump.
    18. Remove nuts attaching the power steering pump to the engine.
    19. Remove power steering pump mounting bracket bolts and nut.
    20. Slide power steering pump/bracket assembly forward and remove stud.
    21. Set power steering pump/bracket assembly aside.
    22. Disconnect the wiring bracket from rear of the right cylinder head.
    23. Remove the generator.
    24. Remove the oil indicator tube bracket bolt.
    25. Remove the generator mounting bracket.
    26. Remove the sixteen cylinder head bolts.
    27. Remove cylinder heads and gaskets.
    28. Clean all sealing surfaces.
    To Install:
    Right Side NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
    NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
    1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
    2. Check the cylinder head locating pins for proper installation.
    3. Place a new cylinder head gasket over the engine block dowel pins.
    4. Install the cylinder head to the engine block.
    5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
    6. Install the cylinder head bolts. gm-03-50-685.gif

    7. Tighten the cylinder head bolts in sequence on the first pass.
      • Torque to: 22 ft. lbs. (30 Nm)
    8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
    9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
    10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
    11. Install the valve rocker arms and pushrods.
    12. Install the generator mounting bracket stud.
      • Torque to: 15 ft. lbs. (20 Nm)
    13. Loosely assemble the generator mounting bracket over the stud.
    14. Install all nuts and bolts finger tight.
      • Torque to: 30 ft. lbs. (41 Nm)
    15. Install the generator.
    16. Install the oil indicator tube bracket bolt.
    17. Install the exhaust manifold.
    18. Install the lower intake manifold.
    19. Install the valve rocker arm covers.
    20. Install the wiring bracket to the rear of the cylinder head.
    21. Connect the accessory bracket.
    22. Install the A/C compressor.
    23. Install the drive belt.
    24. Install the distributor cap.
    25. Connect the spark plug wires to the distributor cap.
    26. Install both heater hoses.
    27. Install the upper radiator hose.
    28. Install the air cleaner assembly.
    29. Refill the engine coolant.
    30. Connect the negative battery cable.
    Left Side To Install:
    NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
    NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
    NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
    NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
    1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
    2. Check the cylinder head locating pins for proper installation.
    3. Place a new cylinder head gasket over the engine block dowel pins.
    4. Install the cylinder head to the engine block.
    5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
    6. Install the cylinder head bolts. gm-03-50-685.gif

    7. Tighten the cylinder head bolts in sequence on the first pass.
      • Torque to: 22 ft. lbs. (30 Nm)
    8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
    9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
    10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
    11. Install the valve rocker arms and pushrods.
    12. Install the power steering pump mounting bracket stud.
      • Torque to: 15 ft. lbs. (20 Nm)
    13. Loosely assemble the mounting bracket over the stud.
    14. Install all nuts and bolts finger tight.
      • Torque to: 30 ft. lbs. (41 Nm)
    15. Install the power steering pump pulley.
    16. Connect the electrical connector to the power steering pump.
    17. Install the exhaust manifold.
    18. Install the lower intake manifold.
    19. Install the valve rocker arm covers.
    20. Install the wiring bracket to the rear of the cylinder head.
    21. Connect the accessory bracket.
    22. Install the A/C compressor.
    23. Install the drive belt.
    24. Install the distributor cap.
    25. Connect the spark plug wires to the distributor cap.
    26. Install both heater hoses.
    27. Install the upper radiator hose.
    28. Install the air cleaner assembly.
    29. Refill the engine coolant.
    30. Connect the negative battery cable.

    Aug 31, 2010 | Chevrolet Suburban 1500 Cars & Trucks

    2 Answers

    Torque specification on a 2003 alero cylinder heads 3.4 liter


    3.4L Engine To Remove:
    1. Remove the lower intake manifold.
    2. Remove the exhaust crossover pipe.
    3. If removing the right cylinder head, remove the catalytic converter from exhaust manifold.
    4. If removing the left cylinder head, remove the engine oil dipstick and tube.
    5. Remove the rocker arms and pushrods.
    6. Remove and discard the cylinder head bolts.
    7. Remove the cylinder head.
    8. Clean the mating surfaces on the following items:
      • Cylinder head
      • Cylinder block
      • Intake manifold
    9. Clean the cylinder block bolt threads.
    NOTE: During disassembly, keep the valve train components together for proper location during assembly.
    To Install:
    NOTE: Coat the cylinder head bolt threads using thread sealer.
    1. If removed, install the following components:
      • Exhaust manifold
      • Accessory studs
      • Spark plugs
    2. Place the cylinder head gasket in position over the dowel pins. Ensure that the THIS SIDE UP note is showing.
    3. Install the cylinder head. Cylinder head torque sequence ’99-‘00 gmpc_v6_14.gif

      Cylinder head torque sequence ’01-05 gm-03-34-682.gif

    4. Install the new cylinder head bolts.
      • Tighten the cylinder head bolts a first pass to 44 ft lb (60 Nm).
    5. Tighten the cylinder head bolts in sequence an additional 95 degrees.
    6. Install the intake gasket.
    7. Install the pushrods and rocker arms.
    8. Raise and support the vehicle.
    9. Install the catalytic converter and dipstick tube and indicator if removed.
    10. Lower the vehicle.
    11. Install the exhaust crossover pipe.
    12. Install the intake manifolds.
    13. Connect negative battery cable.
    14. Fill the cooling system.

    Jul 03, 2010 | 2003 Oldsmobile Alero

    1 Answer

    I need torque specs on 93 dodge 360 ..heads, rocker assembly and torque sequence


    Cylinder Head Bolt 5.9L

    Step 1 - 50 ftlb
    Step 2 - 105 ftlb
    Step 3 - Recheck At 105 ftlb

    Tightening sequence

    Rocker Arm Bolt

    5.9L - 17 ftlb

    Jan 23, 2010 | 1993 Dodge Ramcharger

    1 Answer

    I have 4.9L6 need torque specs for cylinder head


    for cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.


    e023442.jpg

    Dec 05, 2009 | 1988 Ford F 150

    1 Answer

    Blown head gaskit need to remove head and replace with new ong


    2.2L (VIN 4) Engine
    1. Before servicing the vehicle, refer to the precautions section.
    2. Relieve the fuel system pressure.
    3. Drain the cooling system.
    4. Remove or disconnect the following:
      • Accessory drive belt
      • Air cleaner outlet duct
      • Engine mount
      • Intake manifold
      • Exhaust manifold
      • Engine Coolant Temperature (ECT) sensor electrical connector
      • Power steering pump
      • Radiator inlet pipe
      • Spark plug wires
      • Rocker arm cover

      NOTE Whenever valve train components are removed, keep them in order for installation purposes.

      • Rocker arms and pushrods
      • Lifters
      • Alternator rear brace and the alternator
      • Power steering pump
      • Radiator inlet pipe
      • Ignition coil assembly
      • Accessory bracket
      • Spark plug wires
      • Cylinder head bolts

      WARNING Two sizes of bolts are used; note the location of each.

      • Cylinder head
    5. Inspect the cylinder head and block surface for cracks, nicks, heavy scratches and flatness.
    b9d2546.gif
    Cylinder head torquing sequence—2.2L (VIN 4) engine

    1. Install or connect the following:
      • Cylinder head with a new gasket and new cylinder head bolts. Torque the long bolts, in sequence to 46 ft. lbs. (63 Nm) and the short bolts to 43 ft. lbs. (58 Nm) plus an additional 90 degree turn on all the bolts.
      • Lifters
      • Pushrods and rocker arms. Torque nuts to 22 ft. lbs. (30 Nm).
      • Rocker arm cover. Torque the bolts to 89 inch lbs. (10 Nm).
      • Spark plug wires
      • Accessory bracket
      • Ignition coil assembly
      • Radiator inlet pipe
      • Power steering pump. Torque the bolts to 22 ft. lbs. (30 Nm).
      • ECT sensor electrical connector
      • Exhaust manifold. Torque the nuts to 118 inch lbs. (13 Nm).
      • Alternator. Torque the bolts to 37 ft. lbs. (50 Nm).
      • Intake manifold. Torque the bolts to 17 ft. lbs. (24 Nm).
      • Engine mount. Torque the bolts to 55 ft. lbs. (75 Nm).
      • Air cleaner outlet duct
      • Accessory drive belt
      • Negative battery cable
    2. Refill and bleed the cooling system.
    3. Start the vehicle and inspect for leaks.

    Oct 08, 2009 | 2000 Chevrolet Cavalier

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    90 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    78267 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    chargerhp
    chargerhp

    Level 3 Expert

    814 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...