Question about 2000 Ford Contour

1 Answer

Need a rear tail light assembly. hard to find.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ford Master
  • 1,779 Answers

You are correct, they are hard to find! I checked my usual ford sites, and nothing, but found a site with several for sale finally after quite a long search. I have never dealt with this site, but hopefully to can get your tail light assembly through them-good luck!
http://www.automotix.net/usedautoparts/2000-ford-contour-taillight-inventory.html

Posted on Nov 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

Tail light assembly keeps going bad on my 1999 GMC Sierra


You need to help by providing more information about what actually fails in the tail light assembly.

Aug 20, 2017 | Cars & Trucks

1 Answer

I have a 2005 GMC Envoy. Have tail lites but no brake lites. Third lite on top works whet brakes applied


Since the high mounted brake light works you know that the brake light switch is working. Now you need to check the brake light bulbs in the rear tail light assemblies. The brake lights are separate from the tail light (parking or running lights). There are two screws that hold the rear light assemblies in place.

Mar 13, 2011 | 2005 GMC Envoy

3 Answers

Tail lights do not work on a 2000 lexus rx 300 bulbs are fine, all other lights work fine


You may have a fried fuse. Look in your owners manual to find out which fuse it is in the fuse box diagram. If that is the problem make sure to use the same amperage fuse to replace the burned one with. I fried fuse is usually a sign that you have a short somewhere. But they can also fry for other reasons such as excess moisture somewhere. Sometimes they just burn from age and fatigue. It may solve it to just replace the fuse, but if there really is a short, the new fuse will fry too.

Dec 29, 2010 | 2000 Lexus RX 300

1 Answer

How do you remove and replace the rear tail light assembly


Just open the rear tail gate and you will see 2 plastic fasteners on the side by the tail lamp assembly.You need to pry them out and then pull the lamp assembly out.Hope this helps.Good luck.

Oct 26, 2010 | 2004 Chrysler Town & Country

1 Answer

What do I need to unscrew in the trunk to change the reverse light in my 01 chevy impala


Tail Lamp Assembly Removal & Installation To Remove:
  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.
  8. Remove the side marker lamp socket by turning counterclockwise.
To Install:
  1. Install the side marker lamp socket by turning clockwise.
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
prev.gif next.gif

Oct 18, 2010 | 2001 Chevrolet Impala

1 Answer

Need to replace rear brake light on a 1999 Buick Park Avenue. How do I remove the plastic lenses or assembly?


you will need to open the trunk and remove the carpet covering the inside where the tail lights are, find 2 or 3 nuts which are probably 8 or 10 mm,so use a socket and ratchet,remove the nuts and pull the tail light asembly out from the back and you will find the tail light bulb sockets. release the little latch/lock clips while turning the socket assembly about 1/4 turn counter clockwise and you can check each bulb. watch where the wire harness for each socket and also the tail light assembly is so you dont pinch or damage the wires when putting the tail light assembly back in. your owners manual may also give you these instructions and will tell you the correct bulbs to use for tail, brake and turn signal lights.

Oct 27, 2009 | 1999 Buick Park Avenue

2 Answers

How do i change the rear tail light lens on my 2008 hyundai veracruz


Open the rear hatch. Using a small straight edge screwdriver, insert the screwdriver into the slot at the top of each of the two screwcovers on the inside lip of the tail light assemby and carefull pry open. Remove the two screws using a philips screwdriver. Drape a small cloth over the head of a larger straight edge screwdriver and insert at the tip of the tail light assembly (on the rear side of the car and carefully turn back and forth while wiggling the entire assembly. This will eventually allow you to work the tail light assembly loose from the grip pin that is holding the assembly on. Once removed, replace the appropriate bulb. With the assembly still not installed, have someone step on the brake to ensure the new bulb is working properly. Reinstall assembly. Hope this was helpful....I just changed mine.

Jun 12, 2009 | 2007 Hyundai Veracruz SE

2 Answers

Need help for rear tail light assembly on my 2003 trailblazer


Most of the time you can simply remove the tail light assembly from the car pretty easy and just a few screws. If it sdoes not have the screws going through the front of the housing then its rear mount and must be done by lifting the tailgate to get access. Once in the vehicle you should beable to remove the plastic housing covering up the assembly from the inside. Remove the 3-4 screws or bolts and the tail light assembly. Install the new one just the reverse. Pretty easy just take your time.

Joe

May 28, 2009 | 2003 Chevrolet TrailBlazer

2 Answers

Left rear turn signal bulb is burned out.


Tail Lamp Assembly
Removal & Installation
To Remove:

  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.

  1. To Install:
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
      Please don't forget to rate !!!!!!

    Mar 28, 2009 | 2002 Buick Century

    Not finding what you are looking for?
    2000 Ford Contour Logo

    Related Topics:

    137 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75817 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    fordexpert

    Level 3 Expert

    5495 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...