Question about 1999 BMW 328 Series

1 Answer

1999 328is clutch pedal goes all the way to the floor. Is this a problem?

Posted by on

  • stpnwlfbdda Nov 16, 2009

    THanks MN. There is pressure, and the clutch does engage/disengage. I take it from the answer you gave that the pedal should not go to the floor, yes?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

As long as there is pressure than yes. Otherwise bleed the system and make sure the fluid is full. You can adjust linkage if needed.
You can go to autozone.com and register for full free online repair manual.

Posted on Nov 13, 2009

  • Nate Stansfield
    Nate Stansfield Nov 16, 2009

    The pedal should not touch the floor.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My clutch goes all the way to the floor I have a standard Camaro 96 3.8


clutch pedals are suposed to go all the way to the floor , you sure you dont mean brake pedal (cus thats bad ! ) clutches should travel all the way to floor and release the "grab" of the engine about 2/3 down , this way they are more smoothly allowing shifting thru the gears and not jerking as you shift thru the gears , if clutch pedal does not start to "grab" the engines power by 2/3 off the floor and fully "grab"its power all the way up(slipping) ,and you have a hydraulic clutch (96's do) then the clutch disk may require replacement or there is a oil leak in the clutch/master/slave cylinder , look for small oil leaks from under car in area of foot pedals
clutches should be replaced as an assembly that includes , disk ,pressure plate, throwout bearing , with engine side clutch plate magnafluxed for heat cracks and any hydraulic oil leaks replaced or repaired

Mar 12, 2015 | 1996 Chevrolet Camaro

1 Answer

Clutch pedal goes almost to the floor before it engages


If your fluid was low (which is why you likely added some,) you may need to "bleed" your clutch master cylinder.

Mar 26, 2014 | 1991 Nissan Stanza

1 Answer

Clutch pedal goes to floor and half works on my b2200 1987 mazda pick-up


If the clutch is hydraulic operated, you need to bleed the clutch at the slave cylinder, down on the transmission housing. Bleed it just like you bleed brakes of air in the line-open bleeder valve, someone pushes clutch pedal slowly to floor, close valve, and repeat until fluid comes out valve in a steady stream. Make sure the clutch reservoir is full before starting. It uses regular brake fluid.
If not hydraulic, it would be cable operated. Adjust the cable until clutch pedal is right.

Dec 29, 2012 | Cars & Trucks

1 Answer

After changing transmission and clutch in 91 Wrangler, clutch goes to floor. Tried bleeding line but didn't work.


The clutch should go to the floor =) But if it's not disengaging the clutch disk, there's definitely a problem between the pedal and the clutch disk. I'm guessing you have a hydraulic clutch?

Apr 19, 2012 | 1991 Jeep Wrangler

1 Answer

Clutch pedal goes strait to the floor??clutch won't bleed up??


It has air bubbles on the piping, fill the deposit with brake solution, and push and pull the clutch pedal with your hand it doesn't matter if it goes straight to the floor if that happens pull it with your hand, repeat that as if you are bleeding it up, then disconnect the piping beneath the car, the air bubbles will be forced out, then reconnect the piping and repeat the procedure, push and pull the clutch pedal like a 100 times, then disconnect the piping and reconnect. The clutch pedal should be able to go back when there is no air on the piping. If that doesn't work, replace your clutch pump

Jun 23, 2011 | Honda CR-V Cars & Trucks

2 Answers

Clutch pedal just goes to floor in L200


check the fluid level in the slave cylinder, near the master cylinder where break fluid goes in, if it is empty, fill it with hydrolic fluid...you may have to bleed the lines at the tranny if you ran it out which it sounds like.

Mar 20, 2010 | 2006 Mitsubishi Colt

2 Answers

UNABLE TO ENGAGE GEARS WHEN ENGINE RUNNING ( CAN ENGAGE GEARS WITH ENGINE OFF ). CLUTCH PEDAL GOES STRAIGHT TO THE FLOOR WHEN PRESSED


Need to have it check could be clutch master cylinder or slave cylinder or hose from clutch master cylinder to slave cylinder.check brake fluid at clutch master cylinder sit next to brake master cylinder if empty could have a leak. fill and pump peddle and look for leak.

Jan 12, 2010 | 2001 Ford Focus

1 Answer

No pressure clutch pedal goes straight to the floor 1988 holden r


If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Aug 11, 2009 | 1993 Isuzu Rodeo

1 Answer

Clutch Pedal to Floor


slave cylinder needs replaced

Nov 12, 2008 | 1991 Jeep Wrangler

1 Answer

Clutch pedal goes to the floor, then after pulling it up there is pressure...


There is either air in the system or a leak in the clutch slave cylinder. Check your fluid make sure it is full and the cap is tight.

Sep 18, 2008 | 1996 Pontiac Sunfire

Not finding what you are looking for?
1999 BMW 328 Series Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...