Question about 1995 Ford F250

1 Answer

Is there a special tool to disconnect the fuel line from the tank on a 98 f-250 heavy duty, the one with the long collar, the chort one comes off fine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

Just sqeeze the bulk couple and pull.

Posted on Nov 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you change the fuel pump?


Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect the negative battery cable.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Rear seat cushion
    • Plastic access panel
    • Fuel pump wiring harness connector
    • Fuel lines
      7922jg34.gif

      View of fuel pump fittings through the floor pan
      Click to Enlarge 7922jg35.gif

      Remove the locking ring from the fuel pump sender with special tool Fuel Tank Sender Wrench D84P-9275-A
      Click to Enlarge

    • Fuel pump module lock ring. Use special tool Fuel Tank Sender Wrench D84P-9275-A.
    • Fuel pump module

To install:

  1. Install or connect the following:
    • Fuel pump module with a new O-ring seal
    • Fuel pump module lock ring using special tool Fuel Tank Sender Wrench D84P-9275-A
    • Fuel lines
    • Fuel pump wiring harness connector
    • Plastic access panel
    • Rear seat cushion
    • Negative battery cable
  2. Start the engine and check for leaks and proper operation.
shinehutt_37.gif

hope this helps plz vote comment reply if need more help

Jan 17, 2011 | 2002 Mercury Cougar

1 Answer

How to replace a fuel pump on a 2003 grand cherokee laredo


Easiest to do if the tank is mostly empty (fuel is very heavy) If full, use a floor jack with a piece of plywood to distribute the weight (empty out before re-installing) You need to disconnect the fuel fill and vent lines, remove the straps then remove all smaller lines and electric.
Once the tank is down, the collar unscrews and the assembly lifts out. (careful on re-install that you don't damage the arm on the fuel gauge float.)
Reverse procedure to re-install. Never run any pump without fuel not even for a minute!
Good luck

Apr 21, 2010 | 2003 Jeep Grand Cherokee

1 Answer

How to replace a 2005 grand am 6 cyclinder fuel pump


You need to drop the fuel tank...pump is inside. remove the screws under the fill neck opening that hold it to the body, disconnect the fuel line connections and harness, remove both straps holding the tank in (support it, if there is fuel inside its very heavy).Remove the fill and vent hose from the tank. Remove the collar that holds the pump in and carefully remove the pump assembly. Carefully replace pump and make sure it goes in without damaging the float arm and points in the same direction the old one did. reverse order...put it back together. It's best to drain tank and clean the inside before putting it back up. NO SMOKING< ELECTRIC TOOLS OR OTHER IGNITION SOURCES WITHIN 75 FEET OF WHERE YOU ARE WORKING!!!

Mar 06, 2010 | 2005 Pontiac Grand Am

2 Answers

1999 ford ranger fuel pump needs replaced.


Hello!

REMOVAL

WARNING:
  • DO NOT SMOKE OR CARRY LIGHTED TOBACCO OR OPEN FLAME OF ANY TYPE WHEN WORKING ON OR NEAR ANY FUEL-RELATED COMPONENT. HIGHLY FLAMMABLE MIXTURES ARE ALWAYS PRESENT AND MAY BE IGNITED, RESULTING IN POSSIBLE PERSONAL INJURY.
  • FUEL IN THE FUEL SYSTEM REMAINS UNDER HIGH PRESSURE EVEN WHEN THE ENGINE IS NOT RUNNING. BEFORE REPAIRING OR DISCONNECTING ANY OF THE FUEL LINES OR FUEL SYSTEM COMPONENTS, THE FUEL SYSTEM PRESSURE MUST BE RELIEVED TO PREVENT ACCIDENTAL SPRAYING OF FUEL, CAUSING PERSONAL INJURY OR A FIRE HAZARD.
  1. Disconnect the battery.
  2. Relieve the system pressure.
  3. Raise the vehicle.
  4. Drain the fuel tank.

cc999cb.gif
  1. Disconnect the fill pipe hoses.
    • Loosen fill pipe hose clamps.
    • Disconnect fill pipe hoses from the fuel tank.

f3fcce3.gif
  1. Remove the 4 bolts (2 each side) and remove the skid plate if equipped.
  2. Support the fuel tank.

918ba9a.gif
  1. Remove the bolts and pivot the fuel tank support straps away from the fuel tank.

e19f38e.gif
  1. Disconnect the fuel pump connector.
    • Lower the fuel tank slightly. Disconnect the fuel pump connector.


958d5a3.gif
Disconnect the fuel supply line push-connect fitting and the vapor tube fitting at the fuel pump


80378e1.gif
  1. Disconnect the vapor line fitting at the rear of the fuel tank.
  2. Lower the fuel tank.

62ccbfd.gif
To install, reverse the removal procedure


df22959.gif Special Tool(s)

REMOVAL

  1. Clean the area around the fuel pump mounting flange.



b28c7f0.gif
  1. Using the special tool, remove the fuel tank pump assembly locking retainer ring.
  2. Remove the fuel pump assembly. CAUTION: The fuel pump assembly must be removed and handled carefully to avoid damage to the float arm and filter.
  3. Remove and discard the fuel pump mounting gasket.
INSTALLATION
  1. Clean the fuel pump mounting flange and the fuel tank mounting surface.
  2. Apply a light coat of Premium Long Life Grease XG-1-C or -K or equivalent meeting Ford specification ESA-M1C75-B to the gasket to hold it in position during assembly. Install the fuel pump mounting gasket.

4976d12.gif
  1. Using the special tool, tighten the fuel pump assembly locking retainer ring.

Mar 02, 2010 | 1999 Ford Ranger SuperCab

1 Answer

Disconnect fuel lines from fuel tank


There are two types of connectors on these lines. Either brightly colored quick-connects which do not require tools, (Just squeeze the tabs together). Or black quick connects which must be pushed back to remove line.

Jun 21, 2009 | 2001 Jeep Grand Cherokee

1 Answer

How do you disconnect the fuel lines at the fuel tank?


This Requires A SPECIAL TOOL that wraps around the tank side of the hose and slides up under the fitting on the hose side, to releice the spring (YOU CANT SEE) that Holds the Line ON. This can Be found Pretty Inexpensive at your Local Auto Parts Store.

Apr 05, 2009 | 2000 Ford F250 Super Duty Crew Cabs

2 Answers

Removal of fuel lines from fuel pump assembly


There is special disconnect tool just for 98-00 classic CK pickups. Lisle makes them they are a two piece plastic tool that is pretty cheap to buy. Do not buy a regular disconnect tool bcause they will not fit in the lines at the pump. The lisle number at Carquest is 37500. Please rate.

Dec 27, 2008 | 1998 GMC Sierra

1 Answer

Replacing fuel pump on an 05 nissan pathfinder


No special tools required. You first need to remove as much fuel as possible so the tank is not too heavy. Chock the wheels, put tranny in N, remove driveshaft making sure to mark both mating surfaces at rear diff so you put it back on exactly how it came off. Disconnect the filler hose at the tank. Next thing is to lower the tank about 4-5 inches so you can disconnect the electrical connector and hoses to the fuel pump at the top of the tank. I placed a floor jack with a 2' x 1' piece of plywood under the tank, removed the support straps, and lowered the tank enough so I could reach up and disconnect the electrical connector and fuel line hoses from the pump. Once I got everything unhooked I lowered the tank and slid it out from under the vehicle. Replacing the pump is far easier than getting the tank out. There is a locking ring you have to turn remove. Tap is with a wood block or brass punch so as to not cause any sparks. Once it is off, remove the pump and replace. If you are replacing the pump you should replace the fuel sending unit also since these things have a reputation for going bad at 60,000 miles. Installation is the reverse order.

Nov 14, 2008 | 2005 Nissan Pathfinder

1 Answer

Ford E-450 fuel filter removal


YOU NEED T INSERT THE SPECIAL TOOL WICH RELEASES THE RETAINER INSIDE THE BULGED OUT PART OF THE LINE. TRY NAPA FOR TOOL NO. Part: SER 3290 Product Line: NAPA Service Tools WATCH OUT FOR FUEL THAT MAY SPRAY OUT WHILE DISCONNECTING! GOOD LUCK

Aug 26, 2008 | 2000 Ford F Super Duty Chassis Cab

Not finding what you are looking for?
1995 Ford F250 Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...