Question about 2001 Dodge Durango

1 Answer

Replacing front rotors,romoved tires and brake cal. can not remove rotors for anything they will not budge. Am I missing something?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 1,757 Answers

Did you remove the cotter pin, CVJ nut and washer?

Posted on Nov 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to romove and replace sheared lugbolt on rear driver side wheel hub


remove tire...if it has disc brakes remove caliper/pads and rotor...if it has a drum break remove drum..Now take a punch and hammer and hit the center of the lugnut stud untill it pops out the back.put the new one in and get it tight with the lugnut.Replace brakes and tire and tighten that lugnut until it stops.Then check it in 500 miles

Jun 06, 2011 | 1998 GMC Jimmy

1 Answer

Front brakes drag help!!


Try replacing the brake hose they have a tendancy to collapse on the inside over time due to age and will cause brake drag.

Dec 02, 2009 | 1998 GMC Jimmy

2 Answers

Ford F250 SD, 2wd. Replacing front bearing


If you have front disk brakes you have to remove the brake caliper to get the rotor off.

Oct 03, 2009 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

1998 Honda Odyssey, I can't get the front brake rotors off. What is the trick? I tried removing the two phillips head screws which just stripped so I drilled them. Then I used #8 screws in the two...


The m8x1.25 that thread into the rotor act like a "puller". Insert both bolts and turn them each 1 turn at a time until the rotor comes off. They can be stubborn some times.

Sep 19, 2009 | 1998 Honda Odyssey

1 Answer

Cannot remove front rotors. The rotors are rusted badly, and we've removed the tire, the brake pads, the nuts. Won't budge.


you may have too heat them up with a blow torch be carefull of brake lines then hit with hammer in a circular motion

Jun 13, 2009 | 2001 Ford Escort ZX2

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

1 Answer

ABS causing vibration in o4 f-150??


Since the rotor isn't warped. Do you have grooves in the rotor? Are the pads evenly worn? You a bad front 4X4 C/V shaft will also cause this reaction.
I would just unplug the ABS fuse and it will bypass the system to regular old-fashioned brakes.

May 23, 2009 | 2004 Ford F150

1 Answer

Front brake replacement on 96 jetta


changing brakes and rotors on the front are pretty simple this is what you do remove the tire unbolt the brake calapor remove brakes from calapor recomress calapor with comressor kit or c clamp then unbolt the center bolt on the rotor by removing the pin then take bolt off and remove roter when replacing with new i recomend you replace font and real barrings and seals then reverse directions and don't for get to bleed your breaks after your doon

Dec 05, 2008 | 1996 Volkswagen Jetta

Not finding what you are looking for?
2001 Dodge Durango Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...