Question about 2004 Chevrolet Silverado

2 Answers

No turn signals or hazards - 2004 Chevrolet Silverado

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Most likely you have a blown flasher . that is located under the dash board near the fuse box ,but first check the fuse box ,look for the fuse marked signals if the fuse has a wire conecting one side to the other when u look at it the fuse is good .replace fuse ,then pull the round flasher out .. it has two wires on a 90 deg angle and replace it .u can also use a test lamp to check the fuse groun on wire from the test lamp and touch each side of the fuse marked signals . if u get light from both sides of the fuse ,,it is good you can also test each lire on the flasher but one should light up ...

Posted on Nov 13, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 561 Answers

There could be two things wrong here.
1 the flasher unit is defective and needs replacment i think that indicator and hazzard are on the same flasher unit.
2 a fuse has blown and needs repacement or it has a bad conneciton
both should be in the fuse compartment.

Posted on Nov 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

2 Answers

Turn singles and hazards are not working on my 2001 deville


I would replace the turn signal hazard combo switch.

Nov 28, 2016 | Cars & Trucks

1 Answer

Turn signal relay 2007 Avalanche ltz


There is no turn signal relay or flasher , Computer controlled by the BCM - body control module .
Turn Signal/Hazard Lamps
When the turn signal switch is placed in either the left or right position, a ground signal is completed from the turn signal switch to the BCM. When the hazard flasher switch is activated, a ground signal is completed from the turn signal/hazard switch to the BCM. The BCM then sends an ON-OFF voltage signal through the fuses to the appropriate turn signal and side repeater (export only) lamps or to all of the turn signal fuses for hazard operation. The driver door switch and passenger door switch also receive voltage from the BCM turn signal supply voltage circuits for the mirror turn signals. The door switches have no function or control of the mirror turn signals other than a pass through connection for the circuits. The audio chime is also activated when the turn signals are ON. The instrument panel cluster (IPC) receives the signals to activate the turn signal indicators over the GMLAN serial data system. When the hazard switch is pressed, all turn signal lamps will flash including both IPC turn indicators.
This is something best left to a qualified repair shop that has a professional type scan tool . Could need new BCM , which would need programming . Scan tool would be able to check switch inputs for BCM .

May 22, 2016 | 2007 Chevrolet Avalanche LTZ

1 Answer

The fuse for a right turn signal on a 2001 Buick Park Avenue


The left an right turn signals get there power from same fuse ,HZDT/SG fuse 15amp in the left under hood fuse box. through the turn signal hazard flasher module. Here is how they work .
Turn Signal/Cornering Lamps
The HZDT/SIG fuse in the fuse block - underhood - left supplies battery positive voltage to the turn signal/hazard flasher module and have ground at G202. The turn signal lamps may only be activated with the ignition switch in the ON or ACCY position. The T/SIG fuse in the fuse block - underhood - left supplies battery positive voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, current flow is from the turn signal switch assembly to the turn signal/hazard flasher module. The turn signal/hazard flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument cluster (IPC) indicator. When the hazard switch is pressed, all the turn signal lamps will flash including both IPC turn signal indicators. The left turn signals have ground at G106, G400 and at G402. The right turn signals have ground at G105 and G400. The turn signal switch supplies battery positive voltage to the cornering lamps, the left cornering lamp has ground at G105 and the right cornering lamp has ground at G106.The turn signal switch or the turn / hazard flasher module is bad or there is a wiring problem. Go to you tube an check out a few videos on basic electrical testing ,then get a DVOM - digital volt ohm meter , an wiring diagram an trouble shoot the circuit . There may even be a video on test turn signal circuit .

Dec 04, 2015 | Buick Cars & Trucks

2 Answers

Where is the emergency flasher relay located on 2013 Rogue?


Here is what the service manual says. Looks like it is not a flasher relay but a function of the body control module.

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEMSystem Description OUTLINE Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the flasher control function of BCM.
TURN SIGNAL LAMP OPERATION - BCM detects the combination switch condition by the combination switch reading function. - BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is turned ON and the turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION - BCM transmits the turn indicator signal to the combination meter with CAN communication while the turn signal lamp and the hazard warning lamp are operating. - Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal indicator lamp according to the turn indicator signal.
HIGH FLASHER OPERATION (FAIL-SAFE) - BCM detects the turn signal lamp circuit status by the terminal current value. - BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal lamp operating. NOTE: The blinking speed is normal while operating the hazard warning lamp.

Oct 13, 2014 | 2013 Nissan Rogue

2 Answers

After using turn signal you can still hear clinking, is hazard relay part of turn signal


The hazard switch is also the device that supplies the turn signal "flash". If you continue to hear the noise of the turn signal flashing when the turn signals off than the problem is the turn signal switch. It is grounding The purple wire from the hazard switch which makes the hazard switch think the turn signal is on. The fix for this is to relace the turn signal/multi-function switch. Typically they will start to go bad in stages. Your symptom is the first stage. Eventually either the turn signals or the brake lights will also sto working. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Feb 10, 2012 | 2000 Oldsmobile Alero

1 Answer

My hazard lights won't come on at all. The turn signals work fine, as long as the hazard button is not depressed. The hazards used to work, but if the hazard button was pressed and I put on a turn signal,...


sounds like a dirty switch, happens a lot in the UK as the switch is checked for the safety every year so the dirt in the switch causes open circuits, it is a complicated switch, it has many contacts that do different things when in and out, try a salvage yard

May 03, 2011 | 2001 Kia Rio

2 Answers

Turn signal doesn't come on until I hit my hazard light on & off


it could be duel filament bulb that is blown and shorting inside the bulb to the other circuit, you may need to remove all indicator and hazard bulbs and check. I would also try a new flasher can

Apr 17, 2010 | 2003 Chevrolet Impala

2 Answers

Turn signals don't work


i have a similar problem but my left signal works, when i turn the right on it just does an annoying buzz sound. if you can think of any explination for such shinanogins help would be greatly appreciated

Nov 25, 2008 | 1989 GMC K1500

Not finding what you are looking for?
2004 Chevrolet Silverado Logo

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...