Question about Cars & Trucks

1 Answer

Where can i get replacement wires - Cars & Trucks

Posted by on

  • yadayada
    yadayada May 11, 2010

    for what"

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

A salvage yard/junk yard will have factory wires for you vehicle.

Posted on Nov 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many wire harness clips connect to module besides the antenna


Engine Control Module Wiring Harness Replacement - 1.4 L ...

workshop-manuals.com/.../repair.../engine_control_module_wiring_harn...
3. Unclip the 3 wiring harness clips (1, 2) from the engine control module wiring harness brackets. ... Disconnect the wiring harness connection adapter plug (4).

Engine Control Module Wiring Harness Replacement - 1.6 L ...

workshop-manuals.com/.../repair.../engine_control_module_wiring_harn...
5. If equipped, disconnect the engine oil level sensor wiring harness plug (7). ... 10. Unclip the 2 wiring harness clips (2, 6) from the wiring harness brackets.

How to fix wires that break out of plug clips on a wire harness



Dec 01, 2015 | Cars & Trucks

1 Answer

Found the starter wire burnt into for it got close to the engineto replace the wire will it help to start again or not?


a burnt wire would have cause a short when power was sent thought that wire
replace the wire back to good insulation , and replace the fuse for that circuit if it is blown
there should have been no other damage caused

Nov 26, 2015 | 2004 Kia Sedona

1 Answer

Mazda Soho 1.3 endura engine wires burnt. After wires were replaced everything worked. Now the car wont start even after replacing coil pack.Help me please.


My best guess with such limited info. Is that when the new Wiring was done one or more wires were Set next to the Exhaust manifold. These get extremly hot. and will Melt thru the wires and then they short out on the metal. I would look for melted wires. and replace the melted area and Keep away from the hot metal of the engine.

Sep 29, 2014 | Cars & Trucks

1 Answer

HOw to replace spark plug wires on a 1998 Mitsubishi montero sport?


Installing New Spark Plug Wires Is Simple, Especially Of One Wire Is Replaced At A Time. Compare The Length Of The Old Wire With The Length Of The New Wire. Replace Each Wire With One Of Equal Length.Make Sure The New Wire Is Fully Attached On The Plug And In The Distributor Or Coil Module.

Spark Plug Wire Replacement Is More Complicated If All The Wires Are Removed At Once.Then You Must Use The Engine Firing Order And Cylinder Numbers To Route Each Wire Correctly.

Apr 09, 2010 | 1998 Mitsubishi Montero Sport

1 Answer

NEW PLUGS AND WIRES


The correct arrangement?

I always remove one plug wire, replace that spark plug, and then replace that one spark plug wire. This way I never cross which plug wire to which position.

Oct 29, 2009 | 1999 Volkswagen Jetta

1 Answer

We replaced the plug wires and now the car will


If you're SURE you got all the wires on the correct way, then one or some of the wire leads are possibly not attached to the plug itself firmly. Or attached to the Cap correctly. Possibly old piece of wire left on plugs.

Oct 09, 2009 | 1988 Volkswagen Fox

1 Answer

Spark Plug Wire Replacement


the easiest option is to unplug one wire and change that plug, then put the new wire on, repeat for all plugs and wires.

May 08, 2009 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

Keeps mis-firing on cylinder #3 check engine light flashes and stays on car chugs on uphill slopes


check plugs wires for damage or just replace if you have replaced the #3 plug already if not replace it also

Aug 04, 2008 | 1999 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...