Question about Cars & Trucks

1 Answer

1995 camero ignition removal

How to remove the ignition on a 1995 camero

Posted by on

  • yadayada
    yadayada May 11, 2010

    ignition what? key cylinder, switch what? waiting to hear.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 87 Answers

  • Remove the air-bag from the steering wheel of the car. You will need to use a number 26 torx bit and unscrew the 4 bolts behind the wheel. Make sure you unplug the wires of the air-bag.
  • Use a 3/4 inch socket to remove the center nut on the steering shaft.
  • Use a steering wheel puller kit to remove the steering wheel. Place the bolts provided in the puller kit in the 2 holes on either sides of the center shaft.
  • Connect the puller to those bolts while keeping the puller inline with the center steering shaft.
  • Tighten the bolt on the top of the puller until snug then turn 1/4 turn more then strike the bolt with a non-maring hammer the steering wheel should pop off. If not, tighten bolt 1/4 turn more and strike.
  • Now you have access to the ignition lock. Use a 10mm socket and extension to loosen the silver bolt about 2in in from the keyhole. Now pull the old lock straight out and unplug the 2 orange wires that come out with it.
  • Take the new ignition and reconnect the orange wires and insert the lock back into the column.
  • Retighten the 10mm silver bolt.
  • Place the steering wheel back onto the center shaft and simply push down, now special tools are needed for reassembly.
  • Take the air-bag and connect the wires and bolt it back up using the 4 bolts in the back of the steering wheel.
  • You must purchase the ignition lock from a certified Cheverolet dealer. If you do not give them the vin number of the car the correct lock may not be given to you. This is because the chip in your key is 1 of 15 different values that match the passkey 2 computer behind the radio (to the right a bit) otherwise you will need to bypass the passkey system by putting the proper resistor inline so the unit thinks it is reading the key, but this also bypasses a portion of your anti-theft system.

Posted on Nov 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace ignition wires


replace them one at a time and match the old on up to the new ones for lenght

Aug 16, 2012 | 1995 Chevrolet Camaro

1 Answer

How to change a starter 1995 3.4 v6 eng: Chevy camero automatic


First make sure to disconnect the battery. Remove the wires connection of the starter and mark the connection it will useful to connect it again with the new one. Remove the mounted bolts. Now starter slide out of flywheel assembly. You can replace your starter at http://www.buyautoparts.com/autoparts/Chevrolet/Camaro/Starter.html

Aug 02, 2011 | Chevrolet Camaro Cars & Trucks

1 Answer

I have a 1995 camero and it wont stop turning over ...had to disconnect battery


Ignition switch is defective. Replace it. Not the key lock but the ignition switch, normally mounted under the dash on the steering column.

Apr 23, 2011 | 1995 Chevrolet Camaro

1 Answer

Is the Engine wiring harness the same as the for automatic than a standard shift. Engine was removed from another camero,same year,the car had an automatic,my car is stardard shift


my 95 camero 3.4, won't start it has spark and fuel but i think the fuel injectors are't working. i have no check engine lite on.

Oct 20, 2010 | 1995 Chevrolet Camaro

1 Answer

How do i change the starter in my 1993 camero


disconnect the red terminal from battery. jack up car enough to get under. secure with jack stands. near rear of engine under car, is the starter. unplug electrical harness from starter. remove bolts. as you remove the bolts, starter will come down. remove, put new one in. put bolts in, tighten bolts. plug electricfal harness in to new starter. lower car from jack stands. connect red terminal to battery. if you have an alarm, put key in ignition to on position before connecting battery.

Sep 18, 2010 | 1993 Chevrolet Camaro

1 Answer

My ignition switch on a 95 chevy camero has locked up and wont turnsometimes if you giggle the steering wheel it will turn over but it has really jammed now


If you can remove the ignition lock assembly and take it to a locksmith they can rekey it for about $20.00.With age the pins in the lock will start ti jam.

Jan 21, 2010 | 1995 Chevrolet Camaro

1 Answer

Unable to disable my security system/alarm on my 95 Chev. Camero


yes, do some internet searching, I believe there is a control that you unplug inside the hatch on the left hand side, remove the inside plastic panel, undo the connection, wait 5 minutes then reconnect. This I have done once along time ago on a 94 model. Remember I am only here to help and wish this works for you. Good luck.

Dec 16, 2009 | 1995 Chevrolet Camaro

1 Answer

How to change the fuel injector seals on a chevy camero 1995


The injectors should be connected to the fuel rail, which looks like a long shiny tube, about the size of a sharpie marker. remove any bolts securing it to the in-take manifold. Then carefully lift the fuel rail off the top of the engine and u should be able to see all of the injectors.

Oct 14, 2009 | 1995 Chevrolet Camaro

1 Answer

Cant remove starter from 95 camero son says exhaust manifold has to come out please anyone HELP


never done one mate but i wouldnt have thought so but possible ,although hear a lot of this but with a 3/8th drive socket set you should be able to remove the bolts but as for getting it out?? cant help because i have never seen one of these cars here in spain ,anyway best of british with it

Oct 03, 2009 | 1995 Buick LeSabre

1 Answer

No power to ignition 96 camero dl


Check the wires to the distributer or to the modules could be poor or no conection. If you can turn the car over but no spark it's probably something to do with ignition, distributer, module, or wiring to the ignition.

Dec 28, 2008 | 1996 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...