Question about 2004 Toyota Camry

1 Answer

I have a 2004 toyota camry. it has a VERY low brake pedal. i have had new (disc) brakes installed in the front and the rear (drum) brakes have been adjusted. when this was done, the pedal came up a little but returned to its low position very shortly thereafter. is this a common problem and an ordinary situation with the 2004's and something i have to live with or is there something that can be done. the brakes stop fine but the pedal is very low. thank you

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

Start by bleeding the brakes, readjust the rear, make sure the calipers are sliding free, a bad wheel bearing can also cause a problem

Posted on Nov 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 23 t bucket and i cant get a brake pedal.when i bought it had very little brake so i replaced rear shoes and cylinders,front pads and calipers,all new lines and the master cylinder


Once you have bled the air from the brake lines,clamp off the front brake hoses carefully.Does the pedal feel better now?
Then the pad /caliper fit is allowing too much play.Is the pedal the same?Then clamp the rear hose and try the pedal.Is it fine with the rear hose clamped?If so we now know the problem is at the rear brakes.One common low pedal rear brake cause is brake shoes that do not fit the drums.Remove the drums and look at the shoes,are they showing contact wear fully or just in the middle of the shoe?Remove a shoe and place it in the drum.Can you rock the shoe against the drum surface?Once drums have been resurfaced,the shoes will not fit fully against the drum allowing the shoe the flex when applying pressure to it and this can easily create a low soft brake pedal. Of course rear brake adjustment must be correct once brake shoe contact is correct.To correct brake shoe contact,have your shoes re arc-ed to fit resurfaced drums or install new drums.Don't overlook brake master cyl /brake pedal push rod adjustment too.

Jun 24, 2017 | Cars & Trucks

1 Answer

Brake peddle is low,


Pedal, not peddle. First make sure reservoir is full at the brake master cylinder. Then check your brake pads (for disc brakes) and/or brake shoes (for drum brakes). When the pads or shoes are very worn down, you will get a low pedal. If you have disc brakes on the front and drums on the rear wheels, first try just replacing the front brake pads. If you get a good pedal after the front is done, many people tend to let the rear brake shoes go unless they are making noise. These systems are designed to put most of the braking force on the front discs, so the rear shoes do not need changing as often.

May 11, 2017 | Cars & Trucks

2 Answers

Brake esemble diagram


Hey Stan the man,need your vehicles info.,year,make,model and engine size and Tommy on the spot here will send you a picture diagram of your rear brake assembly.There's a special spring tool you can get at auto parts store to remove and install springs,me got one.

Oct 15, 2012 | Cars & Trucks

1 Answer

How do you replace rear drum brakes for 1994 Toyota Camry 4-clydr


See here for details, p37 or p44 depending on the car

http://www.turboninjas.com/camry/br.pdf


As to special tools, a can of brake cleaner spray (must be meant for brake parts), a pair of big strong pliers, a wire brush, and a set of metric spanners.

Aug 18, 2012 | 1994 Toyota Camry

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

3 Answers

2007 camry brakes vibrating


Installing new brake pads on toyota camry solara 2006 front rotors and pads and rear pads. Steering wheel would shake while breaking on 50+ miles per hour speeds. All fixed now.

Jun 22, 2010 | 2007 Toyota Camry

2 Answers

Toyota 2001 Sienna brake problem when i press the brake pedal the brakes aren't as strong as the used to be. Even with new brake pads. I have to pump the brake pedal to make them have more power. What...


Check your brake fluid level. if ok, have the system bled as there may be air in the brake system. If your fluid is low, have the brake system checked for leaks. Hopefully this helps!!

Apr 02, 2010 | 2001 Toyota Sienna

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry


The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

1 Answer

Toyota Camry 2005-Brake pads noise problem


The rear brakes should last from 30000 to 60000 miles or 50000 to 100000 kms. So something is wearing out your brakes too fast. Are you doing the work or some shop. I also assume you have discs and not drums since you mention pads and calipers. I am not certain but usually you need a tool to turn the pistion in when putting in new pads. I would make sure the pads are releasing properly by raising rear of car, stepping on brakes a few times (with engine off and try see if wheels are free by spinning by hand, also try to use handbrake a few times and release it and see if wheels spin freely. Maybe rears always applied. Notice burning smell, are discs glazed from heat? Are you using really cheap pads. Also check the proportioning valve which will decrease pressure to rear brakes during hard braking. Do you notice rear wheels squeling during hard braking. Do you have antilock brake system? Also are you using good quality pads and rotors.

Apr 30, 2009 | 2004 Toyota Camry

2 Answers

When brake is applied,the rear light on the panel come on.


You might wanna have your rear brakes checked along with the rear brake calipers or cylinders, as well as the rear drums or discs, depending on weather your car has rear drum brakes or rear discs brakes. Some cars come equipped with brake sensors that let you know when theres a problem. It would also be a good idea to check you brake fluid level.

Mar 12, 2009 | 1990 Toyota Camry

Not finding what you are looking for?
2004 Toyota Camry Logo

463 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...