Question about 2002 Dodge Durango

1 Answer

I can't get my remote to work with the program. Can you help?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

You may need to replace the battery in you keyless remote stop by any autozone or battery plus and they test it for free wish you the best Michigan Man.

Posted on Nov 12, 2009

Testimonial: "Thanks I have new batteries in the new remote I used this to fix. ATTENTION: You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a Locksmith or dealership use a computer to program the first remote for you. 1. Press LOCK button 5 times at 2 second intervals to resynchronize remote. 2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can go without cranking engine). Wait for ignition chimes to stop. 3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10 seconds. 4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then press the PANIC button ( on the programmed remote ) for 1 second and release both buttons. A chime will sound to indicate that the remote programming mode has been entered ( allow 3 seconds for chime to sound ). 5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons simultaneously then press and release just the UNLOCK button on the same remote. A chime will sound indicating the remote has been programmed. Press and release the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on each new remote you wish to program at this time. Locks will cylce afer each additional remote is programmed. 6. Turn the ignition OFF and remove key. 7. Test Remotes. Without a second remote - the dealership will need to program it for you. "

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Changed battery and now remote doesn't work. it is on a 2005 ford freestyle


press the helpful button,there appears there is more then one type of remote, I think one has auto start and one does not.

owners manuals in the glove box and in there was the Ford Auto Start Remote booklet. For those of you who need to program a new auto start remote, you turn the ignition to the on position, push and hold the little over-ride button (mine is down on the left side kick plate near the hood release) for about 15 seconds, you will hear a chirp which means the system is ready to be programmed, just hit the lock key on your remote and the system will chirp acknowledging the remote has been programmed, continue to do this will all other remotes you have within I believe it was 20 seconds - then shut off the ignition and test your remotes. Worked perfectly for me.
OR

Free Do It Yourself instructions from your friends at Lessco Electronics

1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode.

2. Within 20 seconds press any button on first keyless remote. Door locks will cycle to confirm programming.

3. Within 20 seconds, press any button on second keyless remote. Door locks will cycle again to confirm programming.

4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
Link below
2005 2006 Ford Freestyle Factory Transmitter Remote Fob Programming

Jan 26, 2016 | Ford Cars & Trucks

1 Answer

Remote control car parts


You may need to reprogram the remotes.
1. Turn ignition to run position (as far as you can go without starting engine).
2. Using any Working remote, press the UNLOCK button for 4 to 10 seconds.
3. Within the specified 4 to 10 seconds, continue pressing the UNLOCK buton and press
the PANIC button for 1 second and release both buttons at the same time. A chime will
sound within 3 seconds to indicate that the vehicle has entered remote programming
mode.
4. Within 30 seconds of the chime, press any button on all remotes to be programmed
including previously programmed remotes. A chime will sound after each remote is
programmed.
5. Turn ignition to OFF and remove key.
6. Test all remotes.

Aug 12, 2013 | Chrysler New Yorker Cars & Trucks

1 Answer

How do I program an additional remote for my 2003 Durango


  • You must have a programmed FOB to program another at home with my instructions below. If you don't have programmed one then you must get the first one programmed at the dealer.

  1. Press LOCK button 5 times at 2 second intervals to re-synchronize remote.
  2. Insert key into the ignition switch.
  3. Turn ignition to the run (no start.)
  4. Wait for ignition chimes to stop.
  5. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
  6. seconds.
  7. Within the specified 4 to 10 seconds, continue to hold the UNLOCK button and then press the PANIC button ( on the programmed remote ) for 1 second and release both buttons. A chime will sound to indicate that the remote programming mode has been entered ( allow 3 seconds for chime to sound ).
  8. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons simultaneously then press and release just the UNLOCK button on the same remote.
  9. A chime will sound indicating the remote has been programmed. Press and release the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on each new remote you wish to program at this time. Locks will cycle after each additional remote is programmed.
  10. Turn the ignition OFF and remove key.
  11. Try your remote.
  • Hope this helps.

Oct 23, 2011 | 2003 Dodge Durango

1 Answer

Can't find the keyless remote module under steering column to reprogram my remotes 1195 Chevy Blazer


Here is what i found for your 95 blazer. Hope it helps a little bit.

1. Locate the red two wire programming connector located near the central
locking control module. Behind LH lower instrument panel.

2. Inside the red programming connector you will see two pins.
Jump the two pins with a section of wire. A paper clip bent in a "U" shape will also work.

3. System should now lock and unlock doors to indicate vehicle has entered
programming mode.

4. Press any button on keyless remote once. System should now lock and unlock
doors indicating the keyless remote has been programmed.

5. Repeat step 4 to program the other remote.

6. Remove jumper wire from programming connector to exit programming mode.

7. Test Remote(s).

Sep 02, 2011 | 1995 Chevrolet Blazer

1 Answer

How to program key fob 2003 durango


You must have one working remote to add one more to the system.
If you do not have one working remote right now then these instructions will not work.
You will have to have a Locksmith or dealership use a computer to program the first
remote for you.



1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.
2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can
go without cranking engine). Wait for ignition chimes to stop.

3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
seconds.

4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then
press the PANIC button ( on the programmed remote ) for 1 second and release both
buttons. A chime will sound to indicate that the remote programming mode has been
entered ( allow 3 seconds for chime to sound ).

5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons
simultaneously then press and release just the UNLOCK button on the same remote.
A chime will sound indicating the remote has been programmed. Press and release
the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on
each new remote you wish to program at this time. Locks will cycle after each additional
remote is programmed.

6. Turn the ignition OFF and remove key.
7. Test Remotes.




If I've helped you, please vote!

Feb 02, 2011 | 2003 Dodge Durango

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

Need to program a keyless remote on 2003 Liberty


the instructions say they are the same for up to 06. Need a working remote to make this work. On your programmed remote:
- Switch the ignition to the on position.
- Press and hold the Unlock button for at least four seconds. While holding this button, press the panic button and then release both buttons at the same time. You may or may not hear a chime from the vehicle.
- Within 30 seconds, on all remotes to be programmed (including the original "programmed remote")press and release the lock and unlock buttons at the same time, followed by pressing ANY button on the remote.
- Switch the ignition to off or wait 30 seconds for the programming mode to clear.

Just did it last eve; also can find more details in the Owners Manual (However you only need one working keyless remote to program another keyless remote. You should be able to use the electronic vehicle information center (EVIC) on the overhead console to train remote (Owner's Manual, p. 132-133). However, on my 2005 Liberty this does not show up as an option like it does on my 2003 Liberty.) or Jeep KJ Service Manual.

Hope it works for you (remember rated this help).


Mar 05, 2010 | 2003 Jeep Liberty

1 Answer

I have 2 identical remotes for my 02 Chevy blazer I cannot get them both to work at the same time. Whenever i program the 2nd one the first one doesnt work. Then when i program the first one the second one...


when you go into programing mode and program a new remote the vehicle forgets the first one. you will have to program both remotes one at a time while the vehicle is in reprogram mode

Jan 06, 2010 | 2002 Chevrolet Blazer

1 Answer

REPROGRAM THE FOB DODGE DURANGO 2004


ATTENTION: You MUST HAVE one working remote to add one more to the system.
If you do not have one working remote right now then these instructions will not work.
You will have to have a Locksmith or dealership use a computer to program the first
remote for you.



1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.
2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can
go without cranking engine). Wait for ignition chimes to stop.

3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
seconds.

4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then
press the PANIC button ( on the programmed remote ) for 1 second and release both
buttons. A chime will sound to indicate that the remote programming mode has been
entered ( allow 3 seconds for chime to sound ).

5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons
simultaneously then press and release just the UNLOCK button on the same remote.
A chime will sound indicating the remote has been programmed. Press and release
the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on
each new remote you wish to program at this time. Locks will cylce afer each additional
remote is programmed.

6. Turn the ignition OFF and remove key.
7. Test Remotes.

Thanks for using FixYa - a Very Helpful rating is appreciated for answering your FREE question.

Jul 09, 2009 | 2004 Dodge Durango

1 Answer

Remote wont program


Is this the procedure u are using? this is from the factory manual.

ATTENTION: You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a Locksmith or dealership use a computer to program the first remote for you.

1. Turn ignition to the RUN position (as far as you can go without starting the engine).
Wait for chimes to stop.
2. Using original programmed remote, press and hold the UNLOCK button on the
remote for between 5 and 10 seconds.
3. While holding UNLOCK button, and before 10 seconds passes, press and release
the PANIC button. A chime will sound to indicate that the transmitter programming
mode has been entered.
4. Within 30 seconds of the chime, press a button on all remotes to be programmed
into the system including any previously programmed remotes, a chime will
sound after each remote has been programmed.
5. Turn the ignition OFF to exit the transmitter programming mode.

6. Test Remotes

Apr 09, 2009 | 2006 Dodge Durango

Not finding what you are looking for?
2002 Dodge Durango Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...