Question about 2002 Ford Taurus

1 Answer

Squeaky lifter - 2002 Ford Taurus

Posted by on

  • yadayada
    yadayada May 11, 2010

    are u 100% sure of this, I am a Ford tech and have never seen this.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 708 Answers

CD2 will help quiet lifters. I have never used on a car that new so you may want to check with a repair shop before adding it. Aside from that you will be into some very costly repairs because the has to be partially dismantled. Also, try changing oil and getting some fresh oil.

Posted on Nov 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dist noise


Got squeaky brakes, hey. Or is it chirping? Squeaky brakes are fairly common on vehicles that have all four wheels that are disk. Now, chirping is a different story, it could mean that you will need new disk pads and possible have the rotators turns and if the can't turn the rotators then they need to be replaced. Squeaky brakes, glazing on the pads, pad dust, little rocks, brake spiders, loose adjust spring, and many other possibilities. GB...stewbison

Aug 31, 2011 | Nissan Quest Cars & Trucks

1 Answer

Squeaky, squeaky,squeaky!!!! husband changed the serperntine belt....on his way to job interview...hope he makes it...oh yesterday truck died on the freeway a coupla times...he took out the...


The thermostat is a spring loaded round device that keeps the coolant from flowing long enough for the engine to warm up and then it opens to allow fluid to flow to the radiator.

The serpentine belt is a different issue, but related through the water pump which circulates coolant.

Aug 24, 2010 | 1988 Chevrolet K1500

2 Answers

Is there a diagram for the cylinder heads of a 1991 5.7 liter engine, especially the valve components? Thank you, Dan


Hydraulic Lifters REMOVAL & INSTALLATION 4.8L Engines
  1. Remove the rocker cover.
  2. Remove the engine side cover.
  3. Back off the rocker arm adjusting nuts and remove the pushrods. Keep them in order for installation.
  4. Reaching through the side cover opening, lift out the hydraulic lifters. If your are going to re-use the lifters, remove them one at a time and mark each one for installation. They must be re-installed in the same locations. If a lifter is stuck, it can be removed with a grasping-type lifter tool, available form most auto parts stores.
  5. Inspect each lifter thoroughly. If any of them shows any signs of wear, heat bluing or damage, replace the whole set. To install:
  6. Install and coat each lifter with engine oil supplement.
  7. Install the remaining components by reversing the removal procedure.
  8. Once installation is complete, adjust the valves as described in the valve lash procedure. Fig. 1: Stuck lifters must be freed using a slide hammer type lifter removal tool tccs3813.jpg
4.3L, 5.0L, 5.7L And 7.4L Engines
  1. Remove the cylinder head cover.
  2. Remove the intake manifold.
  3. Back off the rocker arm adjusting nuts and remove the pushrods. Keep them in order for installation.
  4. Remove the lifter retainer bolts, retainer and restrictor.
  5. Remove the lifters. If your are going to re-use the lifters, remove them one at a time and mark each one for installation. They must be re-installed in the same locations. If a lifter is stuck, it can be removed with a grasping-type lifter tool, available from most auto parts stores.
  6. Inspect each lifter thoroughly. If any of them shows any signs of wear, heat bluing or damage, replace the whole set.
  7. Coat each lifter with engine oil supplement prior to installation. Tighten the retainer bolts to 12 ft. lbs. (16 Nm). Adjust the valves as described in the valve lash procedure.
6.2L And 6.5L Diesel Engines Fig. 2: Diesel engine valve lifter 84903155.gif
  1. Remove the cylinder head cover.
  2. Remove the rocker arm shaft, rocker arms and pushrods. Keep all parts in order and properly identified for installation.
  3. Remove the clamps and lifter guide plates.
  4. Remove the lifters by reaching through the access holes in the cylinder head with a magnetic lifter tool. If you are going to re-use the lifters, remove them one at a time and mark each one for installation. They must be re-installed in the same locations. If a lifter is stuck, it can be removed with a grasping-type lifter tool, available form most auto parts stores. To install:
  5. Inspect each lifter thoroughly. If any of them shows any signs of wear, heat bluing or damage, replace the whole set. NOTE: Some engines will have both standard and 0.010 in. (.0039mm) oversize lifters. The oversized lifters will have "10'' etched into the side. The block will be stamped "OS'' on the cast pad next to the lifter bore. and on the top rail of the crankcase above the lifter bore. WARNING
    New lifters must be primed before installation. Damage to the lifters and engine will result if new lifters are installed dry!
  6. Prime new lifters by immersing them in clean kerosene, engine oil or diesel fuel and working the lifter plunger while the unit is submerged.
  7. Prior to installation, coat the lifter roller with engine oil supplement. Re-used lifters must be installed in their original positions!
  8. Install the lifters.
  9. Install the guide plates and clamps. Tighten the clamp bolts to 18 ft. lbs. (26 Nm).
  10. After all the clamps are installed, turn the crankshaft by hand, 2 full turns (720°) to ensure free movement of the lifters in the guide plates. If the crankshaft won't turn, one or more lifters may be jamming in the guide plates.
  11. The remainder of assembly the reverse of disassembly.
prev.gif next.gif

Aug 17, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Squeaky sway bar, is it bushing or linkage?


More than likely it is the bushings where the bar mounts to the frame. Pull these out and lubricate them with a silicone based grease and this should solve the trouble.

Jul 21, 2010 | 2000 Chevrolet Tracker

2 Answers

Need instructions on how to change the lifters in my 1998 Chevy S10 2.2L


Please don't forget to rate!!!!

2.2L Engine When installing new lifters, a pre-lube should always be applied to the lifter body. It is also a good idea to prime hydraulic lifters by submerging them in clean engine oil and depressing the plunger using an old pushrod. This allows the internal components of the hydraulic lifter to coat with oil before initial operation in the engine. All lifters should be replaced when a new camshaft is installed.
If any valve train components (lifters, pushrods, rocker arms) are to be reused, they must be tagged or arranged during removal to assure installation in their original locations.
  1. Remove the rocker arm cover.
  2. Remove the cylinder head assembly from the engine.
  3. Remove the bolts retaining the lifter anti-rotation brackets, then remove the brackets.
  4. Remove the hydraulic roller lifters from the bores.
  5. Inspect the lifter and lifter bore for wear and scuffing. Examine the roller for freedom of movement and/or flat spots on the roller surface.

a3ab0ce.gif
Remove the bolts retaining the lifter anti-rotation brackets ...


bb0d44a.gif
... then remove the anti-rotation brackets


79533e9.gif
The lifters are located in bores in the engine block


a298166.gif
Use a lifter removal tool to remove the lifters from the bore

To install:
If installing a new lifter, coat the lifter body with a suitable camshaft pre-lube
  1. Install each hydraulic lifter to its bore being careful to align the flat sides (top) of the lifters with the flat sides of the anti-rotation brackets. When properly installed the flat sides of each lifter are aligned parallel to the anti-rotation bracket. The roller at the bottom of the lifter is parallel to the camshaft lobe.
Make sure to properly align and install each lifter as improper installation of the lifters or brackets could result in engine damage.
  1. Install the anti-rotation bracket retaining bolts and tighten to 97 inch lbs. (11 Nm).
  2. Install the cylinder head.
  3. Install the rocker arm cover.

d477687.gif
Removing the hydraulic roller lifter from the 2.2L engine

Feb 06, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

Squeaky noise When I press down trunk of my 2004 honda accord


YES and dont forget to check your break discks

Jan 29, 2010 | 2004 Honda Accord

1 Answer

I have 99 p71 that makes squeaky sound when i dive


ball joints...if it is coming from the front end or could be universal joints

Oct 26, 2009 | 1999 Ford Crown Victoria

2 Answers

Air conditioning compressor making squeaky sound


can someone tell me if a squeaky noise when I turn on my ac in my yukon, means the air compressor is going out? Please help!

Aug 15, 2009 | 2003 Chevrolet Tahoe

1 Answer

2000 ml320 transfer case squeaky noise


hi,better to bring your car to gas station with car lifter,lift your car ,you can determine where the noise come from,or maybe you can see the rotation of your proffeler shaft,ty

Apr 05, 2009 | 2000 Mercedes-Benz M-Class

Not finding what you are looking for?
2002 Ford Taurus Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...