Question about 2003 Mercedes-Benz Mercedes Benz G Class

1 Answer

Hi I have 2003 Mercedes G 500,and I have transfer case on low,position and wont shift back to hi

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 134 Answers

Try putting the vehc. in nuetrel and try shifting it back to hi if that doesnt work try ake the battery termanils off from 5 min and then put the vehcin neutr and try switching it back.

Posted on Nov 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Silverado 4WD. Service 4WD dash light comes on after engaging 4WD and acts up by engaging itself randomly for several days, then goes back to normal.


Check connection at the 4X4 control module , check power and grounds . Do you know how to do basic electrical testing ? Does your truck have manual or automatic trans mission ? Which transfer case does yours have ?

The NVG 263 transfer case features a three button shift control switch located on the instrument panel. When the ignition is in the RUN position, the transfer case shift control module (TCCM) starts monitoring the transfer case shift control switch to determine if the driver desires a new mode/gear position. At a single press of the transfer case shift control switch, the lamp of the new desired position begins flashing to inform the driver that the TCCM has received the request for a new mode/gear position. The lamp continues to flash until all shifting criteria has been met and the new mode/gear position has been engaged. Once the new mode/gear position is fully active, the switch indicator for the new position remains ON constantly. In the event that the TCCM can not or will not complete the shift, the indicator returns to the previously selected position; this is a Transfer Case Shift Control Switch Indicator Flashes, then Returns to Previous Mode condition.

The NVG 263 transfer case provides the driver with 4 manual mode/gear positions:
• 2HI - 2 Wheel Drive high range
• 4HI - 4 Wheel Drive high range
• 4LO - 4 Wheel Drive low range
• Neutral
Have it check for DTC'S - diagnostic trouble codes ?

DTC B0790
DTC B2725
DTC C0306
DTC C0327
DTC C0359
DTC C0379
DTC C0550

Your best bet would be take it to a qualified repair SHOP

Dec 28, 2016 | Cars & Trucks

1 Answer

My 98 f150 was in 4WD Hi this morning when I started it. Selector switch is in 2WD position. 4WD Hi light is on, hubs (or front differential) is engaged and transfer case engage. (Feel front wheel hop...


If the switch was in the 2WD position and the transfer case was locked in a 4WD range, my 2 SWAGs would be bad switch or the connector to the shift motor is damaged / corroded or the fuse to the transfer case shift relay module is blown ( fuse # 17 ) / problem with the transfer case shift relay module.

This is without knowing if the truck was used in 4WD the night prior, and shifted out just before turning off. If this is the case, the shift motor might be stuck, and a few hits with a dead blow hammer to the transfer case might jar it free again ( do not use a metal hammer, it could damage the transfer case ).

The vacuum shift solenoids on the firewall are controlled by the GEM ( Generic Electronic Module ) which is grounding either the 2WD or 4WD solenoid, depending on the shift plate contacts in the transfer case. ( when in 4 or 4H, the contact switch plate signals the GEM, which in turn grounds the correct solenoid ).

Pulling the switch will not cause the transfer case to go back to a default position, the switch has a resistance level for each mode, and needs that value to operate the shift motor.

The resistance values for the switch between the 2 dark blue wires:
2WD - 4100 to 3700 ohms
4H - 1050 to 1150 ohms
4L - 380 to 340 ohms
- find the wire locations on the switch, mark them and remove the connector to test the resistance.

Just my opinion on the order :

1. Check the fuses for the shift motor
2. Try the old school shift method, back up ~ 50' put into park or neutral, and shift from 4WD to 2WD.
2.1. This is to see if the transfer case shift motor is bound up, and reversing might release it
3. Try hammering the transfer case with a dead blow hammer while someone shifts from 2WD to 4WD. You only need the key in the run position, if it happens quick enough after running the engine, the vacuum reservoir will still have enough vac to operate the solenoids. Don't chance running yourself over.
3.1. If this frees up the shift motor and the vacuum has bled off, you can try starting the truck and shifting into 4H then back to 2WD to get the front axle to disconnect or manually vacuum operate the front disconnect motor by applying vacuum to the pink vacuum line on the shift motor on the front axle.

Mar 05, 2011 | 1998 Ford F150 Regular Cab

1 Answer

My 1999 suburban also stuck in 4 wheel. when i push the button to go into 2 hi it flashes the acuator pulls in then goes back into 4 hi. it wont stay in 2 wheel drive. i have replaces the control on the...


Did you ever think of having it diagnosed by a qualified repair shop ? Thier are aspects associated with this system you have no clue about. That's the first thing every one goes for , changing the switch . It flashes because codes are stored .
DTC B0768 Service Indicator Circuit High
DTC B2725 ATC Mode Switch Circuit Malfunction
DTC C0300 Rear Speed Sensor Malfunction
DTC C0305 Front Speed Sensor Malfunction
DTC C0308 Motor A/B Circuit Low
DTC C0309 Motor A/B Circuit High
DTC C0310 Motor A/B Circuit Open
DTC C0315 Motor Ground Circuit Open
DTC C0323 T-Case Lock Circuit Low
DTC C0324 T-Case Lock Circuit High
DTC C0327 Encoder Circuit Malfunction
DTC C0357 Park Switch Circuit High
DTC C0362 4LO Discrete Output Circuit High
DTC C0367 Front Axle Control Circuit High
DTC C0374 General System Malfunction
DTC C0376 Front/Rear Shaft Speed Mismatch
DTC C0387 Unable to Perform Shift
DTC C0550 ECU Malfunction
DTC C0611 VIN Information Error
You need a professional scan tool to check for these codes an too view data parameters .
Transfer Case Shift Control Module
The transfer case shift control module uses the VIN information for calculations that are required for the different calibrations used based on axle ratio, transmission, tire size, and engine. The system does not know which calibration to use without this information.
The direct battery supply line (CKT 1640) provides the power to the module and motor circuitry.
Transfer Case Encoder Motor
The transfer case encoder motor consists of a permanent magnet (PM) DC motor and gear reduction assembly. It is located on the left hand side (drivers side) of the transfer case. When activated it turns the sector shaft of the transfer case (clockwise or counter clockwise) to shift the transfer case. The encoder motor is controlled with a pulse width modulated (PWM) circuit within the transfer case shift control module. This circuit consists of a driver on both the Motor A and Motor B circuits. The encoder motor is bi-directional to allow the motor to shift the transfer case from 2HI or 4HI to neutral and 4LO positions.
Transfer Case Encoder
Your best bet ,take it to a qualified repair shop .

Jul 18, 2017 | 1999 Chevrolet Suburban

2 Answers

My 4x4 is stuck in four wheel low it is shift on the fly and i have already replaced the transfer case motor


Ok here is a long shot but sometimes it will work. Put the 4wd position switch to 4wd Lo, put your transmission in reverse and back up for about 50 yards, stop and put your transmission in neutral, then shift the 4wd to 4wd hi, wait a few seconds and shift the 4wd to 2wd hi, Sometimes the t-case will get stuck and this is how you reset the computer. I have known people that really got their t-cases messed up because they thought that shift on the go meant that they could shift the t-case into 4wd LO while moving but shift on the go is only for 4wd hi the gears will not mesh up fast enough for 4wd LO because the ratio is 1 to 1 . I hope this helps you.

Feb 08, 2010 | 1990 Ford Bronco

1 Answer

Four wheel wont engage.Are the wires from trans case,where do they lead to


Hi:
Your push button 4 wheel drive system has the push button panel, a shift control module, which is located behind the center console, and a shift control motor, which is on the side of the transfer case. If your transfer case is still ok, you can unbolt the shift control motor, and cycle the shift buttons to see if it moves. Most likely failed part is the shift control module,

Dec 16, 2009 | 2003 Chevrolet S-10

1 Answer

02 dakota wont shift from 4hi to 2 hi


Try commanding the drive ranges while in netural cycling them. This may normalize the controller that senses the position from the encoder motor assembly. There maybe a procedure for that in a service manual.

Dec 12, 2009 | 2002 Dodge Dakota Club Cab

2 Answers

1996 chevy blazer will not go into 4wd hi but it will go in to 4wd lo. when you push the 4 Hi button it just flashes and then does nothing.


The major components to this system are a shift control motor that is mounted to the transfer case, and a shift control module that is behind your center console. since the transfer case is still shifting into 4wd lo, the shift motor is still moving somewhat, so the most likely cause is the shift control module, but there isn't an easy way to troubleshoot between the two...

Nov 16, 2009 | 1996 Chevrolet Blazer

1 Answer

How to shift into 4wd


Ford has 2 types of 4x4 system engagement. One is a knob on the dash that you just turn to 4wheel drive high or low. The other system is the 4x4 transfer case shift on the transmission tunnel (hump) between the driver and passenger seats. To shift into 4 wheel drive high while driving, just let off the gas and shift transfer case into 4H position, and continue driving. To shift into 4 wheel drive Low, stop the vehicle completely, put transmission in neutral, shift transfer case into 4Low position, put trans. in gear, and start driving. I am assuming before doing the above, you have locked in ( turned the front hubs to 4 wheel drive position.) Any further questions, let me know.

May 16, 2009 | 2003 Ford F150 Regular Cab

3 Answers

Can,t get truck out of 4x4 low range


try putting your truck in neutral and then shifting into 2 wheel drive shift on the fly does not apply to 4 low only 4 high and on electric shift models it wont shift unless your ****** is in neutral.

Aug 26, 2008 | 1999 Ford F250 Regular Cab

1 Answer

4x4


Need to know engine size and what codes are stored. Put the unit into neutral and shift 4x4 between positions. Listen to the shift motor on the transfer case for operation. Send the info back and I'll check the forum later.Good Luck.

Aug 20, 2008 | 2002 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...