Question about 2004 Dodge Dakota

1 Answer

The heater and AC fan will not come on anymore. Its first started with it only working on med and high then went to only working on high and now nothing. I have takent out the fan and tested it and it is working fine I have replaced the control board right behind the knobs. what else could it be?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,236 Answers

Wire harness. check the wires going into the fan and the console for corrosion.

Posted on Nov 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ac/heater will only work on low when you move it to med or high it shuts off


need to check switch,resistor and fan ---ur switch might have resistor built in it would need to be tested for continuity for the other speeds --if your truck [didnt specify which ] has a separate resistor it should be attached to the heater fan motor housing again resistor needs to be tested -also test ur fan for any resistance or overheating

Apr 10, 2014 | 1993 Toyota Pickup

1 Answer

Ac/heater onlu works on low


you either have a bad switch or bad fan motor. I would start by replacing the switch

Apr 09, 2014 | 1990 Toyota Corolla

1 Answer

2008 Honda Odyssey AC fan works on low and med speeds but no high speed blower


There should be a high speed blower relay that bypasses the resistor for slower speeds.
Check with an auto parts store or the dealer.

Jun 23, 2012 | 2008 Honda Odyssey EX-L

1 Answer

The fan speed switch for the heater/ac will not work on the two lowest speeds, only med to high. Went to a salvage yard and got a replacement one, it does the same thing. Apparently there is something...


You need to get the blower motor resistor replaced.This is your problem.It is located by the blower motor.There will be a connector from the blower to the resistor.The resistor controls the fan speeds when you turn the knob on the control head.The blower motor is on the passengers side under the dash.Hope this helps.Good luck.

Mar 05, 2011 | 2003 Buick Century

1 Answer

2005 Sienna AC Heater fan is very noisy


the fan may be loose on its drive shaft and catching the housing

Jul 07, 2010 | 2006 Toyota Sienna

1 Answer

Why does my heater in my 2000 ford ranger only work on the high setting?


I assume that you are talking about the heater fan?

Your heater FAN has at least 3 settings, and for our purposes we will assume low,med and high

Low and medium run through a resistor High is wired direct
Either your resistor is bad or your fan is
I know it seems wrong that the fan could be shot but it could be pulling so many amps that it won't work in any other mode than high
I just had this happen on one of my trucks
Start with the fan

Apr 06, 2010 | 1998 Ford Ranger SuperCab

2 Answers

Rear AC fan will not run in lo med or hi, switch or is there resistors on the fan that need checked?


When a blower motor does not turn on in low or med. and only turns on high its usally a resistor block. If nothing works it is most likely the bolwer motor itself or a fuse.

Feb 28, 2010 | 2001 Chevrolet Suburban

3 Answers

Why wont my heater or ac fan not blow in my car?


Check fuse panel for blown fuse first.

Dec 21, 2009 | 1995 Mercury Tracer

1 Answer

Ac & heater


Disconnect the wire from the fan, turn the car on, test the voltage between the connector to ground (chasis) on all fan speed settings (high,med,low). If you have voltage at all settings (approx. 12.3V on high and less as the speed setting is lower) then replace the fan motor (about $50 at autozone). If there is not voltage on all speed settings you will also need to replace the blower motor resistor (about $12 at autozone). The whole process takes about 20 mins.

Oct 09, 2008 | 1999 Oldsmobile 88

1 Answer

4 speed blower (fan)


You'll have to go to the dealer and buy a new switch panel. There is a circuit board behind the switch panel that went bad on yours. Don't get one from the wrecking yard, I made that mistake once.

Aug 11, 2008 | 1996 GMC Jimmy

Not finding what you are looking for?
2004 Dodge Dakota Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...