Question about 1999 Ford Contour

1 Answer

Replace pulling is give out - 1999 Ford Contour

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Ford Master
  • 3,433 Answers

?????? Say that again, please..

Posted on Nov 12, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2004 f-150. 1,2,3 and 4 cylinders are not hitting. A couple of days ago it was 1,2 and 6 not hitting. Have put it on 3 different computers and all give me different codes. Any suggestions would...

replace your VCT sencor (variable cam timing) on right bank easy to get to very front of valve cover on top with wire conector un plug pull rubber boot and ther is only 1 8mm bolt loosen it and pull VCT from valve cover and replace just as pulled

May 13, 2012 | 2004 Ford F150

1 Answer

97 chevy 1500 truck with 5.7 no codes stall out when you give it gas you can hear it misfireing in the intake replaced the dist and set timing with a scanner runs ok when its cool as long as you dont give...

there is a very real possibility that you may have a flat lobe on the camshaft. Last time I heard one like this, it almost sounded like a popcorn machine in the intake. sound you don't forget. Also, check for a stretch timing chain. Pull plugs, rotate engine to TDC. Pull dist cap off. Put finger on rotor and have someone rotate engine in opposite direction untill you feel rotor move. Look at how far it goes on the timing tab untill you feel the rotor move. Half of that number is the amount of stretch. 4 or more degrees, change chain.

Oct 04, 2017 | Chevrolet Cars & Trucks

2 Answers

Is it easier to pull the motor when replacing the transmision, or is there a way i can replace it from under the car.

You can replace from underside without pulling engine, just make sure is raised at least 18 inches give yourself room to work and for clearance.

Feb 18, 2011 | 1999 Saturn SL

1 Answer

How do you replace the rear brakes on a 2001 Ford F250

First, get a set of brake shoes.
Second pull off wheels on both sides then remove the brake drums on both sides.
On one side pull off brake shoes springs clamps ect.
Using the side not dissasembled as an example, use it as a reference while assembling the side apart. Then pull apart the other side, and use the side reassembled to put together that side using it as a reference.
Replace drums and wheels, good luck, and give me a nice vote please.

Jul 12, 2010 | 2001 Ford F250 Super Duty Super Cab

1 Answer

Do I replace the right side drive shaft on my 06

lower ball joint, strut mount, and pulling the halfshaft. you have to pull it out of the tranaxle and pull the spindle bolt. The ball joints let the steering knuckle hang loose to give it enought room so you can pull the halfshaft out the the transaxle.

May 20, 2010 | 2006 Toyota Solara

1 Answer

Replacing headlight on 2004 trailblazer

should be 2 small rods that you rotate and pull up on, then the whole light assembly should pull off, giving you access to the bulbs.

Nov 11, 2009 | Chevrolet Cars & Trucks

1 Answer

1999 Tahoe rear seat relase quit working; can't fold down seat!

There is a cable that pulls the release when you fold down the bottom seat. Broken cable can be repaired by replacing cable.

Aug 09, 2009 | 1997 Chevrolet Tahoe

2 Answers

Replacing a brake light Tercel 1999

1999 Tercel rear light bulb replacement. Snap off 2 black caps to pull back carpet. Remove 2 screws on outside of trunk at the edge of trunk lid. The light fixture will loosen up. Sqeeze the tongs on the square white plastic plug on the inside and push plug through hole. You may have to give the light fixture a tug. Turn bulb holder and pull it out. Pull out bulb and put in new one.

Apr 02, 2009 | 1997 Toyota Tercel

1 Answer

Can't remove bulb from socket/housing to replace plate light

Spray a little penetrating spray like WD-40, down into socket, give it a couple of minutes and wiggle from side to side & pull & see if that works.

Mar 24, 2009 | 2001 Mazda Tribute

2 Answers

INstrument panel light out how to replace

grab both sides of cluster and just pull unit towards you. Nothing holds it in but 4 clips and 4 rubber grommets. Just dont yank too hard or youll pull wires off the back.

Dec 27, 2008 | 1995 Mercedes-Benz S-Class

Not finding what you are looking for?
1999 Ford Contour Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5653 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides