Question about 1989 Plymouth Sundance

1 Answer

Lights when the head lights are on the break light, and blinker on the left do not work. The left blinker won't blink at all whether the head lights are on or not, unless I keep moving the switch up and down, if the head light are on then even that won't make it blink or even come on. I have replaced all the bulbs and fuses, including the big round fuse under the dash.

Posted by on

  • findingmealo Nov 12, 2009

    Thank you I will buy a new switch today.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 770 Answers

Not sure if this is "all" of your problem, but you definately have a defective switch because of the fact that you can wiggle the switch and make the blinker work. Replace the switch and see where that leaves you. It may cure all your woes. Good Luck. I hope this is helpful!

Posted on Nov 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 95 camaro the blinkers just quit working. The hazard lights work, but the blinkers don't work even if the blinker switch is turned on no lights blikeor come on


There is more than one flasher. One is for hazards and the other flasher is for directional signals. They are located under dash just left and right of the steering column. Don't go tearing up the steering column, then you are asking for trouble. Try the least expensive and labor intensive fix first.

Sep 25, 2017 | 1995 Chevrolet Camaro

1 Answer

My dash lights want come on and my left brack light want come on and my right blinker want come on.


1st off the right blinker,does it blink fast or not at all if it blinks fast, check the bulbs if it is not blinking and the dash light also don't work the multifunction switch could be bad(turnsignal,light switch) if your other break light is working start by checking the bulbs take the verified good one and try it in the other side if the bulbs are good check the fuses under dash and under hood carefully

Nov 30, 2010 | 1991 Honda Civic

1 Answer

96 contour. left tail light, 1 and 2nd break light are out.


Everything works, more or less, so you know that the switches and fuses are good. That means that you've got either bulb problems or power/ground problems. First, try swapping the bulbs around to see if the "bad" lights will work with the known "good" bulbs in them. If so, you just need to replace some bulbs. If not, check the sockets inside and out for corrosion, clean them (wire brush, steel wool, sandpaper, etc.) if necessary, and use a voltmeter or automotive tester to make sure that you have power and ground to each socket. The fast flash on the turn signal is just an indicator that a bulb is out.

Bill B

Apr 28, 2010 | 1996 Ford Contour

1 Answer

Right read blinker/break light dont work, turn signal blinks rapidly


It's the bulb. There are two filliments in the bulb. One is for when you turn your lights on and the other is for breaking and blinker flashing. When the break filliment goes bad it causes the blinker to flash very rapidly. 100% the bulb. Change it and all will be good again. P.S. if it were a fuse none of the break lights or blinkers would work.

Apr 20, 2009 | 2005 Ford Explorer

1 Answer

Left signal lights wont shut off all back running lights off


sounds like a turn signal switch on the column

Apr 04, 2009 | 1997 Eagle Talon

2 Answers

Front blinker and run light don't work


Look at the second page of the diagram at the link. The flag "E" in lower right has power coming from the switch. It goes to the instrument cluster, right mirror turn indicator, and right front turn bulb. Is the instrument panel light blinking? How about the mirror? Use these facts to find the break in the wire. If none of these lights is blinking, the switch may be broken, as yadayada indicates. See page 1 at the link. It has a separate contact for the rear light, which is why the back can work and not the front, even though the switch is broken.
http://www.revbase.com/BBBMotor/Wd/DownloadPdf?id=123629

Nov 07, 2017 | 2006 Ford F-150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...