Question about 1994 Ford Probe

1 Answer

How do you take the dash out of a 94 probe gt?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 720 Answers

Hiya,

This dashboard assembly diagram for the Protege, should be very similar to the Probe.

Hope it helps...

Cheers,

How do you take the dash out of a 94 probe gt? - 28f85db.gif

Posted on Nov 12, 2009

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 272 Answers

SOURCE: 94' Ford Probe Automatic Transmission fluid check question

The car needs to be running with the transmission warm, (drive around for at least 10 minutes) Place the car in neutral. Pull the stick wipe it off and place it back in the transmission. Reads just like an oil stick, want fluid in the safe range (checked pattern) area.

Posted on May 12, 2009

  • 103 Answers

SOURCE: How do you open up the rotary distributor on a 94

i think u replace whole distributer assebly (very very expensive dealer iterm)

Posted on Mar 17, 2010

  • 19 Answers

SOURCE: i need timing belt digrams for a 94 ford probe gt ...

moz-screenshot-1.pngAlign the engine timing marks as follows, then install the belt.

ae00695.gif

f446780.gif
Once the belt is routed, as shown below, install the indicated pulley last, then pull the pin out of the hydrualic-tensioner.
cc4ecb7.gif

Posted on Jun 27, 2010

  • 14036 Answers

SOURCE: need to know how to

DISCONNECT AND PLUG THE RESERVOIR HOSE FROM CLUTCH MASTER CYLINDER. CAP THE BRAKE LINES AND MASTER CYLINDER PORTS. REMOVE THE MOUNTING NUTS AND REMOVE THE MASTER CYLINDER.

Posted on Jun 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My ford probe gt was going down the road, died as i was driving it. will not start


You will need to find out if you lost spark to the plugs or fuel to the injectors to proceed.
Let me know if you need more info.

Jul 24, 2012 | 1994 Ford Probe

2 Answers

Dash / tail lights 94 ford probe not working


Check fuse panel for blown fuses and check trunk wiring for cut wire and check tail bulbs for blown light.

Aug 15, 2010 | 1994 Ford Probe

1 Answer

I need timing belt digrams for a 94 ford probe gt has a 6 cylindar engine


moz-screenshot-1.pngAlign the engine timing marks as follows, then install the belt.

ae00695.gif

f446780.gif
Once the belt is routed, as shown below, install the indicated pulley last, then pull the pin out of the hydrualic-tensioner.
cc4ecb7.gif

May 20, 2010 | 1994 Ford Probe

1 Answer

How to replace a front right strut on a 94 probe


You have to rent a spring conpresser tool. You can buy one but try to search for a place that rents them. Good luck!

Nov 05, 2009 | 1994 Ford Probe

2 Answers

Dies after starting


Sound like the faulty diode on the Distributor which is a common problem on the '93 up to '94 and half V6 Probes. Never was recalled but should have been. Pop in a new Distributor from a mazda or ford and you're golden if that is the problem. My t distributor was a mazda but made by mitsubishi. Go figure, both are excellent Japanese car companies.

Jun 02, 2009 | 1993 Ford Probe

2 Answers

94' Ford Probe Automatic Transmission fluid check question


The car needs to be running with the transmission warm, (drive around for at least 10 minutes) Place the car in neutral. Pull the stick wipe it off and place it back in the transmission. Reads just like an oil stick, want fluid in the safe range (checked pattern) area.

May 12, 2009 | 1995 Ford Probe

1 Answer

1989 to 1990 Powered door conversion


about the only advice i can give is that i did the same thing with a 94 probe base and a 94 gt. i had to take the whole wiring harness out of the gt and put it in the base. It starts from the inside fuse block, goes to both doors, under the front seats, all the way to the fuel pump, abs, tail lights, and pretty much everything from the dash to the rear of the car. If you can get a whole harness, it should work.

Mar 09, 2009 | 1990 Ford Probe

1 Answer

94 ford probe,speedometor,oil gage,odometer not working


You need to pull the dash and check the guages look for any burning or melting. You may just need to replace the pannel in your dash, pretty easy work. If not start checking the wires and cables that come out of your faulty guages.

tepfy

Feb 22, 2009 | 1994 Ford Probe

1 Answer

94 Ford Probe GT Fuel Cutout problem


VERY Probable! You need to get that Probe to a Mechanic and have it Diagnosed. You can also Purchase a Diagnostic tool for the Computer at Any Good Auto Parts Store and Try this yourself! This is Most Definitally a Computer Error Code Problem.

Jan 02, 2009 | 1994 Ford Probe

Not finding what you are looking for?
1994 Ford Probe Logo

Related Topics:

606 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...