Question about 2000 Lexus RX 300

1 Answer

Method for removing master window switch on 00 RX300? Not unpluging, just panel removal from door panel.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 81 Answers

Insert a small flathead screwdriver under the rear of the switch panel and pull up, it might be kind of hard to get out so pull hard! a tip for not scratching the panel would be to put electrical tape on the end of the screwdriver that your using.

Posted on Nov 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove and replace drivers side power window switch


I am assuming its the drivers door window you are speaking of....
The drivers door has the master window switch w/lockout. The entire assembly must be replaced. The individual switches on the drivers door can't be replaced by themselves. Some GM vehicles allow the panel with the switch assembly to be removed without removing the door panel. However, most require the door panel to be removed for access to the window switch assembly. The master door/window switch assembly is not cheap, by the way.
I would check/replace the window relay first. Usually located under the dash, or under one of the seats.
Might just be the window motor on the problem window.

Jul 08, 2013 | 2001 Cadillac Eldorado

1 Answer

Replace master window switch


You need to remove door panel and the pull switch out of holder and unplug.

Apr 21, 2013 | 1999 Jeep Cherokee

1 Answer

Passenger electric window does not work from passenger switch or driver master switch. How do you test whether the malfunction is wiring, switch or motor? How do you remove the door panel?


ok, i couldnt remember how to get the door panel off on your specific car, so while looking it up i came across this video from 1a auto. http://www.youtube.com/watch?v=m1CaEXsa0Xg

now as for testing the window system the quickest way i have found is, to start at the motor, sometimes its as simple as a loose ground or worn connection.

unplug the connector for the window motor, and with a multimeter you will want to check for voltage, if voltage is present, your window motor is bad. If no voltage is present, remove the switch on the passenger side, unplug the connection and perform a continuity check on the switch itself.

hope this helps

Apr 03, 2011 | 1999 Mercury Sable

1 Answer

I need to know how to get the drivers side door panel off. My window is off track and I need to fix


how to remove door panel on a 97 expedition, pull up on master window switch bezel careful clips break easily and unplug the connectors, remove triangle trim piece top right side of panel pull out then up, screw behind it remove it, remove red lense plastic piece on bottom of door small screw driver careful breaks easily screw behind it remove it, remove bezel around door handle turn it to get off handle screw behnd it remove it, pull straight up on door handle gently then hard if needed, after it is loose from door remove light bulb socket from behind door panel turn it, unplug power window switch.
thats it reverse to put back on

Nov 25, 2010 | 1997 Ford Expedition

1 Answer

How to remove drivers door panel on 1999 ford escort. I need to repair the windows switch for the drivers side. My window is in the down position and won't come up when I push the button. All other windows...


Remove the front door pull cup screw 1152a96.gif

Remove the screw cap and the screw from the inside door handle and slide the handle rearward to disengage the hook from the inner sheet metal.
  • Disconnect the inside door handle from the front door latch remote control link
37470b2.gif

Remove the two-piece pushpins from the front door trim panel (23942).
2a1605a.gif

NOTE: Use a commonly available spring loaded trim pad removing tool with a long thin nose to prevent damage to the door trim panel.
Release the seven front door trim panel bullet nose fasteners and push inboard, then upward to release the front door trim panel.
  • If equipped, disconnect the master window regulator control switch electrical connector
cc0d2af.gif

Remove the retainer from the master window regulator control switch panel.
  1. Pull outward on the cup retainer tabs and remove.
  1. Remove the master window regulator control switch electrical connector from the retainer
ab8ff6c.gif

Jun 05, 2010 | 1999 Ford Escort

1 Answer

How do I remove the drivers window controls on a 2004 Mercedes Benz C240


Hi,

If you cannot see any bevelled edges to remove the master switch control, my suggestion would be the most common.... to remove all visible screws securing the interior panel to the door frame, e.g. behind door release handle, behind inside grip hande (as circled in photo), then slide & lift the interior door panel away slightly as one assembly, just enough to reveal any electrical wires.

Disconnect all wire looms from behind interior door panel...

Then, view switch assembly from behind the door panel, to determine best method to remove. Most modern switch assemblies are simply held in place by molded clips on the switch body, which need to be pushed out from behind.

36e466a.jpg

Cheers,

"If this has helped you in any way, please rate this solution"

Jan 25, 2010 | 2004 Mercedes-Benz C-Class

3 Answers

How do you take the door panels off?


How To Install Replace Remove Front Door Panel Ford Focus 00-05 1AAuto.com


Nov 08, 2009 | 2001 Ford Focus

1 Answer

How to replace passenger window motor


Door Panels REMOVAL & INSTALLATION Continental 1995–00
  1. Using a small screwdriver, remove the screw cover from the armrest of the front door trim panel.
  2. Remove the two retaining screws.
  3. Using the trim pad removing tool , remove the front door trim panel
  4. Disconnect the electrical connectors.
  5. Remove the front door window regulator switch housing. To install:
  6. Position the front door trim panel on the door, align the two locators on the front door trim panel with the door and reverse the removal procedure.
Power Window Motor REMOVAL & INSTALLATION 1992–00 Vehicles
  1. Disconnect the negative battery cable.
  2. Remove the door trim panel and watershield.
  3. Detach the motor wires at the multiple connector.
  4. Remove the motor retaining screws using Torx® drive bit set D79P–2100–T or equivalent, and separate the motor from the bracket and cable drum housing.
  5. Remove the motor from inside the door. To install:
  6. Position the motor and drive to the cable drum housing and motor mounting bracket. Install the 3 motor screws and tighten.
  7. Connect the power window motor wiring.
  8. Connect the negative battery cable.
  9. Check window operation.
  10. Install the watershield and door trim panel

Aug 31, 2009 | 1998 Lincoln Continental

1 Answer

Remove the electric mirror switch


Removal and Installation

Remove the front door speaker. For additional information, refer to Section 415-00.
Remove the speaker watershield.
Remove the 2 speaker standoffs.
If equipped, remove the window regulator handle.
Separate the handle cover from the handle.
Remove the screw.
Remove the window regulator handle.
Remove the spacer.

Remove the window control switch. For additional information, refer to Section 501-11.
Remove the bolt.
Remove the 2 front door lower bolts.
Remove the door handle cover plate.
Remove the 2 door handle screws.
Remove the front door handle.
Guide the door handle through the opening in the trim panel.
CAUTION: Do not pull directly outward on the front door trim panel, as damage may occur.

Remove the front door trim panel.
Lift upward to remove the front door trim panel.
To install, reverse the removal procedure.

Jun 22, 2008 | 1992 Ford Explorer

Not finding what you are looking for?
2000 Lexus RX 300 Logo

510 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...