Question about 1989 Acura Integra

1 Answer

How do i lower my 89 acura integra

Do i need a special kit or are there parts that i car adjust on my car

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 819 Answers

You will need lowering sprongs and struts, then camber kits for alignment afterwards. if you just by cheap lowering springs, you will not be able to align the car properly after, and it will handle terrible and prematurely wear your tires.

Posted on Nov 12, 2009

  • shortys1519 Feb 06, 2012

    You lower the front with a screw for the torsion bars. Loosen it to lower. Car won't ride good unless you get stiffer torsion bars. For the back get lowering springs/coil overs and shocks

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I adjust the clutch in a 2000 Acura integra


I believe these use a hydraulic clutch system in which case there is no adjustment and the clutch is probably worn out.

Nov 12, 2014 | Cars & Trucks

1 Answer

Need to change rear contol arms on acura integra gsr...how hard is it and how long should it take...also any special tools i need?


there are no special tools required but you must have the alignment redone, that is the most expensive part of the job which will take 2 hours, u will need a good floor jack and safety jack stands to support the car, this is a MUST

May 26, 2010 | Acura Integra Cars & Trucks

1 Answer

What tools to use to remove front struts on 87 acura integra


1) Jack up the ront part of the car and support it with safety stands.
2) Remove the brake hose clamp bolt.
3)Use floor jack to support the lower control arm. You can place the jack under the ball joint. This is very important. You need to have the jack under the ball joint otherwise force of the torsion bar will jump and cause injury.
4) Remove the self-locking bolt on the knuckle. Slowly lower the jack to remove the strut from the knuckle.
5) Remove two self locking nuts from the upper part of the strut.
) Remove the strut ( front damper) from the car.

May 15, 2010 | 1987 Acura Integra

1 Answer

Do I need a special tool to install a crankshaft timing gear on a 1994 acura integra gsr


get a book from auto parts store on your car. its a must have for deep repairs. it will tell you what tools to use. good luck. joeyj35@live

Feb 12, 2010 | 1994 Acura Integra

1 Answer

Can i put a 1994 acura integra ls trans to replace a 1989 acura i


I don't think this would be possible wihtout some hassles.

The engine type build changed twice between the 89 and the 94 series integra.

I would suggest you speak to Honda specialised mechanic before you purchase the 94 tranny.

Also check out the Honda forums as they ahve guys who have done some handy things with the ol integra

Feb 09, 2010 | 1989 Acura Integra

2 Answers

Alternator removal on 87 acura integra


you need to loosen and remove the alternator mounting bolts and remove the V - belt and alternator assembly.

Dec 05, 2009 | 1987 Acura Integra

2 Answers

Honda Integra Headlights


you can use acura integra lights for your honda integra no mater which side is the wheel.

May 17, 2009 | 1992 Acura Integra Hatchback

2 Answers

Overheat


Hi

Renew the temp guage sender.

Good Luck !

John

Feb 06, 2009 | 1989 Acura Integra

1 Answer

Special bolt on the crankshaft pully on 1990 acura integra


It should be a hex bead bolt. Nothing really special about the. If its a bolt that is torqued then tightened to a specific angle then you need to replace it when doing the work.

Dec 30, 2008 | 1990 Acura Integra Hatchback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...