Question about 2002 Land Rover Freelander

1 Answer

My car does not have the same engine specs as you belt is on the passenger side of engine, near engine mounts. please suggest something i can use to replace my serpentine belt. . . Thanks D.D.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,472 Answers

I assume your referring to locking up the cam/crank so that it can be done. There are tools available.If you could give me further detail of your problem I can assist you further. Also here is a guide as well to help you:
here is a manual on cd:
or the Haynes manual here:
Hope this helps.
thank you,

Posted on Nov 12, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How many motor mounts does a 2006 chevy impala have?

There are going to be five. There are two that can be seen from the engine bay that are side mounts near the front of the engine. Underneath you will find one, referred to as the anchor, centered over a crossmember. The remaining two are just behind this mounted to the frame rails. If you are thinking about replacing them, I suggest doing this first from the top, then side to side on the underside. First loosen retaining bolts on all five, support engine with a jack and remove then replace each front mount in turn, leaving retaining bolts snug but loose enough for there to be a little play as you may have to wiggle things around a little on the lower three. Underneath remove and replace first one outer, leaving the retaining bolt out of this one, then the anchor, you will have to work the jack around and probably wiggle some things in order to get out the old one, then to seat the new one. Replace retaining bolt in first frame mount then work the other side. Tighten to spec starting with anchor, then frame mounts then upper side mounts.

Apr 14, 2015 | 2006 Chevrolet Impala

1 Answer

I can't figure out where the black retractor for the shoulder belts gets mounted. Stock belts. I took them out, but back in?

If you are referring to the front seat passenger seat belts, the shoulder belt retractors are mounted to the floor at the base of the driver and passenger side door pillars. They are usually hidden behind the pillar trim panel and the belt comes out thru a slot in the trim piece near the swivel.

Mar 20, 2015 | Cars & Trucks

1 Answer

How do I change the serpentine belt?

It is suggested that a dealership or very good garage perform this task. The passenger side motor mount is in the middle of the belt and must be detached before the new belt can be installed. This is dangerous and the engine must be properly supported before the mount can be removed or damage could result.
Serpentine belts are designed to be very long lasting so it may be possible that the belt may be fine but the belt tensioner may be weak instead. Please consult that garage or dealership, this is really not something for the weekend mechanic.

Jul 09, 2014 | 2005 Chevrolet Equinox

1 Answer

How to change the water pump on a ford festiva 1995

Drain all the coolant.Jack up the car on the front passenger side.Remove the passenger side wheel.Put a jack under the oil pan.Detach the engine mounts on the passenger side of the car.Remove all external belts.Remove the upper timing belt cover boltsLower the engine using the jack.Remove the water pump pulley. (3 bolts)Remove the upper timing belt cover.Disconnect the coolant line running across the front of the engine from the water pump. (2 bolts on a flange)Pull the timing belt.Pull the water pump.Installation is just reversed.

Jun 07, 2012 | Cars & Trucks

1 Answer

Where is the started located on a 2004 dodge neon

I do not know the EXACT location, but can give you an idea of where to look.

Most starters are on the 'right' side of the engine, mounted to the transmission. To determine what I mean by the right side, stand at the transmission side of the engine facing it, the belts should be on the other side of the car from you. Your right is the engine's right. If the belts are near the passenger fender, the starter should be under the manifold up against the firewall, bolted to the transmission. If it isn't there, then check the left side, as cramped engine compartments can cause the manufacturer to deviate from the 'norm'.

Jun 05, 2012 | 2004 Dodge Neon

1 Answer

1999 Honda Accord passengers side motor mount\r\nSeems to be leaking fluid. Spoke with NAPA and they don't show a motor mount on this vehicle being filled with fluid. Any suggestions?

there could be a transmission line or power steering line that runs near or over the mount that may be leaking or the motor or tranny depending on witch side the mount is on may be leaking onto the mount also a more closer inspection would be in need.

Mar 19, 2011 | 1999 Honda Accord

1 Answer

2006 Rav4 2.4 serpentine belt change has kicked my collective psyche enough to question my shadetree abilities. Why can't I locate the connection point for the belt tool (besides there being only 3/4"...

I had to take out the passenger side Engine mount out which will give you more room to access the tensioner nut which is a 19mm. but you will have to be really careful because when you release the tension if you dont do it right you mite end up breaking the tensioner nut which is aluminium and you will have to end up putting a new tensioner assembly along with the belt.

Sep 21, 2010 | 2006 Toyota RAV4

2 Answers

How can I remove an altenator from a 98 ford contour se 2.5 l motor. And what are any suggestions?

Fig. Fig. 5: Alternator mounting-2.5L engine
  1. Disconnect the negative battery cable.
  2. Release the drive belt tensioner and remove the drive belt from around the alternator.
  3. Raise and support the vehicle.
  4. Remove the passenger side front wheel and fender well splash guard.
  5. Disconnect the passenger side outer tie rod end from the spindle. See .
  6. Remove the exhaust system Y-pipe.
  7. Unplug the connectors and remove the cables from the alternator.
  8. Remove the alternator brace retaining bolts and the brace from the vehicle.
  9. Remove the passenger side halfshaft. See .
  10. Remove the alternator mounting bolts and remove the alternator from the passenger side fenderwell.

To install:
  1. Install the alternator on the bracket and tighten the mounting bolts to 29-40 ft. lbs. (40-55 Nm).
  2. Install the passenger side halfshaft. See .
  3. Install the alternator brace and tighten the retaining bolts to 15-22 ft. lbs. (20-30 Nm).
  4. Install the alternator connectors and the cables. Tighten the terminal nut to 80-97 inch lbs. (9-11 Nm).
  5. Install the exhaust system Y-pipe.
  6. Install the passenger side outer tie rod end to the spindle.See .
  7. Install the passenger side fender well splash guard and front wheel.
  8. Lower the vehicle.
  9. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
  10. Connect the negative battery cable.

Mar 15, 2010 | 1998 Ford Contour

3 Answers

Motor mount - 2001 honda oydessy

sounds like you've made the proper diagnosis. if you're intent on changing this, i suggest you get a Haynes guide to show how it should be done. you'll find them at the auto parts store.

Jan 12, 2009 | 2001 Honda Odyssey

Not finding what you are looking for?
2002 Land Rover Freelander Logo

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers


Level 3 Expert

75744 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides